170 lines
6.4 KiB
C
170 lines
6.4 KiB
C
|
// TI File $Revision: /main/11 $
|
||
|
|
// Checkin $Date: June 19, 2008 17:08:04 $
|
||
|
|
//###########################################################################
|
||
|
|
//
|
||
|
|
// FILE: Example_2833xStandbyWake.c
|
||
|
|
//
|
||
|
|
// TITLE: Device Standby Mode and Wakeup Program.
|
||
|
|
//
|
||
|
|
// ASSUMPTIONS:
|
||
|
|
//
|
||
|
|
// This program requires the DSP2833x header files.
|
||
|
|
//
|
||
|
|
// GPIO0 is configured as the LPM wakeup pin to trigger a
|
||
|
|
// WAKEINT interrupt upon detection of a low pulse.
|
||
|
|
// Initially, pull GPIO0 high externally. To wake device
|
||
|
|
// from standby mode, pull GPIO0 low for at least (2+QUALSTDBY)
|
||
|
|
// OSCLKS, then pull it high again.
|
||
|
|
//
|
||
|
|
// To observe when device wakes from STANDBY mode, monitor
|
||
|
|
// GPIO1 with an oscilloscope (set to 1 in WAKEINT ISR)
|
||
|
|
//
|
||
|
|
// As supplied, this project is configured for "boot to SARAM"
|
||
|
|
// operation. The 2833x Boot Mode table is shown below.
|
||
|
|
// For information on configuring the boot mode of an eZdsp,
|
||
|
|
// please refer to the documentation included with the eZdsp,
|
||
|
|
//
|
||
|
|
// $Boot_Table:
|
||
|
|
//
|
||
|
|
// GPIO87 GPIO86 GPIO85 GPIO84
|
||
|
|
// XA15 XA14 XA13 XA12
|
||
|
|
// PU PU PU PU
|
||
|
|
// ==========================================
|
||
|
|
// 1 1 1 1 Jump to Flash
|
||
|
|
// 1 1 1 0 SCI-A boot
|
||
|
|
// 1 1 0 1 SPI-A boot
|
||
|
|
// 1 1 0 0 I2C-A boot
|
||
|
|
// 1 0 1 1 eCAN-A boot
|
||
|
|
// 1 0 1 0 McBSP-A boot
|
||
|
|
// 1 0 0 1 Jump to XINTF x16
|
||
|
|
// 1 0 0 0 Jump to XINTF x32
|
||
|
|
// 0 1 1 1 Jump to OTP
|
||
|
|
// 0 1 1 0 Parallel GPIO I/O boot
|
||
|
|
// 0 1 0 1 Parallel XINTF boot
|
||
|
|
// 0 1 0 0 Jump to SARAM <- "boot to SARAM"
|
||
|
|
// 0 0 1 1 Branch to check boot mode
|
||
|
|
// 0 0 1 0 Boot to flash, bypass ADC cal
|
||
|
|
// 0 0 0 1 Boot to SARAM, bypass ADC cal
|
||
|
|
// 0 0 0 0 Boot to SCI-A, bypass ADC cal
|
||
|
|
// Boot_Table_End$
|
||
|
|
//
|
||
|
|
// DESCRIPTION:
|
||
|
|
//
|
||
|
|
// This example puts the device into STANDBY mode. If the lowest
|
||
|
|
// possible current consumption in STANDBY mode is desired, the
|
||
|
|
// JTAG connector must be removed from the device board while
|
||
|
|
// the device is in STANDBY mode.
|
||
|
|
//
|
||
|
|
// The example then wakes up the device from STANDBY using GPIO0.
|
||
|
|
// GPIO0 wakes the device from STANDBY mode when a low pulse
|
||
|
|
// (signal goes high->low->high)is detected on the pin.
|
||
|
|
// This pin must be pulsed by an external agent for wakeup.
|
||
|
|
//
|
||
|
|
// As soon as GPIO0 goes high again after the pulse, the device
|
||
|
|
// should wake up, and GPIO1 can be observed to toggle.
|
||
|
|
//
|
||
|
|
//
|
||
|
|
//###########################################################################
|
||
|
|
// $TI Release: DSP2833x/DSP2823x Header Files V1.20 $
|
||
|
|
// $Release Date: August 1, 2008 $
|
||
|
|
//###########################################################################
|
||
|
|
|
||
|
|
#include "DSP28x_Project.h" // Device Headerfile and Examples Include File
|
||
|
|
|
||
|
|
// Prototype statements for functions found within this file.
|
||
|
|
|
||
|
|
interrupt void WAKE_ISR(void); // ISR for WAKEINT
|
||
|
|
|
||
|
|
void main()
|
||
|
|
|
||
|
|
{
|
||
|
|
|
||
|
|
// Step 1. Initialize System Control:
|
||
|
|
// PLL, WatchDog, enable Peripheral Clocks
|
||
|
|
// This example function is found in the DSP2833x_SysCtrl.c file.
|
||
|
|
InitSysCtrl();
|
||
|
|
|
||
|
|
// Step 2. Initalize GPIO:
|
||
|
|
// This example function is found in the DSP2833x_Gpio.c file and
|
||
|
|
// illustrates how to set the GPIO to it's default state.
|
||
|
|
// InitGpio(); // Skipped for this example
|
||
|
|
|
||
|
|
EALLOW;
|
||
|
|
GpioCtrlRegs.GPAPUD.all = 0; // Enable all Pull-ups
|
||
|
|
GpioCtrlRegs.GPBPUD.all = 0;
|
||
|
|
GpioCtrlRegs.GPADIR.bit.GPIO1 = 1; // GPIO1 set in the ISR to indicate device woken up.
|
||
|
|
GpioIntRegs.GPIOLPMSEL.bit.GPIO0 = 1; // Choose GPIO0 pin for wakeup
|
||
|
|
EDIS;
|
||
|
|
|
||
|
|
// Step 3. Clear all interrupts and initialize PIE vector table:
|
||
|
|
// Disable CPU interrupts
|
||
|
|
DINT;
|
||
|
|
|
||
|
|
// Initialize the PIE control registers to their default state.
|
||
|
|
// The default state is all PIE interrupts disabled and flags
|
||
|
|
// are cleared.
|
||
|
|
// This function is found in the DSP2833x_PieCtrl.c file.
|
||
|
|
InitPieCtrl();
|
||
|
|
|
||
|
|
// Disable CPU interrupts and clear all CPU interrupt flags:
|
||
|
|
IER = 0x0000;
|
||
|
|
IFR = 0x0000;
|
||
|
|
|
||
|
|
// Initialize the PIE vector table with pointers to the shell Interrupt
|
||
|
|
// Service Routines (ISR).
|
||
|
|
// This will populate the entire table, even if the interrupt
|
||
|
|
// is not used in this example. This is useful for debug purposes.
|
||
|
|
// The shell ISR routines are found in DSP2833x_DefaultIsr.c.
|
||
|
|
// This function is found in DSP2833x_PieVect.c.
|
||
|
|
InitPieVectTable();
|
||
|
|
|
||
|
|
|
||
|
|
// Interrupts that are used in this example are re-mapped to
|
||
|
|
// ISR functions found within this file.
|
||
|
|
EALLOW; // This is needed to write to EALLOW protected registers
|
||
|
|
PieVectTable.WAKEINT = &WAKE_ISR;
|
||
|
|
EDIS;
|
||
|
|
|
||
|
|
// Step 4. Initialize all the Device Peripherals:
|
||
|
|
// Not applicable for this example.
|
||
|
|
|
||
|
|
// Step 5. User specific code, enable interrupts:
|
||
|
|
|
||
|
|
// Enable CPU INT1 which is connected to WakeInt:
|
||
|
|
IER |= M_INT1;
|
||
|
|
|
||
|
|
// Enable WAKEINT in the PIE: Group 1 interrupt 8
|
||
|
|
PieCtrlRegs.PIEIER1.bit.INTx8 = 1;
|
||
|
|
PieCtrlRegs.PIEACK.bit.ACK1 = 1;
|
||
|
|
// Enable global Interrupts:
|
||
|
|
EINT; // Enable Global interrupt INTM
|
||
|
|
|
||
|
|
// Choose qualification cycles in LPMCR0 register
|
||
|
|
SysCtrlRegs.LPMCR0.bit.QUALSTDBY = 0; // The wakeup signal should be (2+QUALSTDBY) OSCCLKs wide.
|
||
|
|
|
||
|
|
// Write the LPM code value
|
||
|
|
EALLOW;
|
||
|
|
if (SysCtrlRegs.PLLSTS.bit.MCLKSTS != 1) // Only enter Standby mode when PLL is not in limp mode.
|
||
|
|
{
|
||
|
|
SysCtrlRegs.LPMCR0.bit.LPM = 0x0001; // LPM mode = Standby
|
||
|
|
}
|
||
|
|
EDIS;
|
||
|
|
// Force device into STANDBY
|
||
|
|
|
||
|
|
asm(" IDLE"); // Device waits in IDLE until falling edge on GPIO0/XNMI pin
|
||
|
|
// wakes device from Standby mode.
|
||
|
|
for(;;){} // Loop here after wake-up.
|
||
|
|
|
||
|
|
}
|
||
|
|
|
||
|
|
/* ----------------------------------------------- */
|
||
|
|
/* ISR for WAKEINT - Will be executed when */
|
||
|
|
/* low pulse triggered on GPIO0 pin */
|
||
|
|
/* ------------------------------------------------*/
|
||
|
|
interrupt void WAKE_ISR(void)
|
||
|
|
{
|
||
|
|
GpioDataRegs.GPATOGGLE.bit.GPIO1 = 1; // Toggle GPIO1 in the ISR - monitored with oscilloscope
|
||
|
|
PieCtrlRegs.PIEACK.bit.ACK1 = 1;
|
||
|
|
|
||
|
|
}
|