Initial commit

Core/Inc/boot_project_setup.h

@@ -0,0 +1,36 @@
+// BOOTLOADER defines
+
+// RCC defines
+#define __RCC_UART_BOOT_CLK_ENABLE() 	__HAL_RCC_USART3_CLK_ENABLE()
+#define __RCC_UART_PORT_CLK_ENABLE() 	__HAL_RCC_GPIOB_CLK_ENABLE()
+#define __RCC_DMA_UART_CLK_ENABLE() 	__HAL_RCC_DMA1_CLK_ENABLE()
+#define __RCC_DMA_SDIO_CLK_ENABLE() 	__HAL_RCC_DMA2_CLK_ENABLE()
+#define __RCC_TIM_BOOT_CLK_ENABLE() 	__HAL_RCC_TIM7_CLK_ENABLE()
+
+
+// USART defines
+#define UART_BOOT 			USART3 			// usart
+#define UART_SPEED 			256000
+#define UART_BOOT_IRQn 	USART3_IRQn
+
+#define UART_PORT 			GPIOB				// usart port
+#define UART_PIN_TX 		GPIO_PIN_10
+#define UART_PIN_RX 		GPIO_PIN_11
+
+
+// DMA defines
+#define DMA_UART_Channel 	DMA1_Channel3
+#define DMA_SDIO_Channel 	DMA2_Channel4
+#define DMA_UART_IRQn 		DMA1_Channel3_IRQn
+#define DMA_SDIO_IRQn 		DMA2_Channel4_5_IRQn
+
+// TIM defines
+#define TIM_BOOT 						TIM7
+#define TIM_BOOT_Prescaler 	64000 // set up for 1 tick - 1 ms (no decrement needed)
+#define TIM_BOOT_IRQn 			TIM7_IRQn
+
+// SDIO defines
+#define SDIO_SDCard_In_PORT GPIOB
+#define SDIO_SDCard_In_PIN 	GPIO_PIN_5
+#define SDIO_SDCard_In_IRQn EXTI9_5_IRQn
+

Core/Inc/bootloader.h

@@ -0,0 +1,90 @@
+#include "main.h"
+
+#include "usart.h"
+#include "dma.h"
+#include "tim.h"
+#include "custom_flash.h"
+#include "gpio.h"
+#include "can.h"
+#include "sdio.h"
+#include "fatfs.h"
+
+
+// KEY defines
+#define BOOTLOADER_KEY_ADR (uint32_t)0x08009800
+#define BOOTLOADER_KEY_PAGE 20
+#define BL_KEY_APP_WRITTEN 0xAAAA5555
+
+// MAIN APP defines
+#define MAIN_APP_START_ADR (uint32_t)0x0800C000
+#define MAIN_APP_PAGE 21
+#define MAIN_APP_NUM_OF_PAGE 250-MAIN_APP_PAGE
+
+// ERROR DEFINES
+
+
+
+struct flag
+{
+	unsigned reInitMCU:1;	 		// флаг перепрошивки (очишает память перед прошивкой новой)
+	unsigned InitOrWait:1;		// флаг активной прошивки (1) или ожидания комманды UART/CAN (0)
+	unsigned StartInit:1;			// флаг что необходимо начать прием прошивки/прошивку
+	unsigned InitBootPeriph:1;// флаг старта инициализации перифирии для прошивки
+	unsigned BootloaderCMD:3; // комманда: интерфейс для прошивки
+	unsigned InitMCUReady:1; 	// окончание прошивки
+	unsigned HalfOfWrite:1; 	// какая половина из dma буфера не записана
+	
+	
+	unsigned SDCardIn:1;
+};
+
+
+
+struct Bootloader_Errors
+{
+	unsigned FLASH_ERASE:1;
+	unsigned FLASH_WRITE:1;
+	
+	unsigned CMD_INVALID:1;
+	unsigned USART_RECEIVE:1;
+
+	
+	#ifdef __CAN_H__
+	unsigned CAN:1;
+	#endif
+	
+	#ifdef __SDIO_H__
+	unsigned SD_CARD_NOT_INSERTED:1;
+	unsigned SD_CARD_READ:1;
+	#endif
+};
+
+
+
+struct Bootloader_Errors_Counters
+{
+	unsigned FLASH_ERASE;
+	unsigned FLASH_WRITE;
+	
+	unsigned CMD_INVALID;	
+	unsigned USART_RECEIVE;
+	
+	#ifdef __CAN_H__
+	unsigned CAN_RECEIVE;
+	#endif
+	#ifdef __SDIO_H__
+	unsigned SD_CARD_NOT_INSERTED;
+	unsigned SD_CARD_READ;
+	#endif
+	
+};
+
+void Bootloader_main(void);
+
+void SD_Programming(FRESULT *res_fresult, HAL_StatusTypeDef *res_hal);
+void Bootloader_TIM_Handler(void); // handler for "WD" Timer
+void Check_CMD_USART(uint8_t *DataUART);
+void SetKey(void);
+uint32_t ReadKey(void);
+void ResetKey(void);
+void Boot_SystemClock_Config(void);

Core/Inc/can.h

@@ -0,0 +1,52 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    can.h
+  * @brief   This file contains all the function prototypes for
+  *          the can.c file
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __CAN_H__
+#define __CAN_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+
+/* USER CODE BEGIN Includes */
+
+/* USER CODE END Includes */
+
+extern CAN_HandleTypeDef hcan;
+
+/* USER CODE BEGIN Private defines */
+
+/* USER CODE END Private defines */
+
+void MX_CAN_Init(void);
+
+/* USER CODE BEGIN Prototypes */
+
+/* USER CODE END Prototypes */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CAN_H__ */
+

Core/Inc/custom_flash.h

@@ -0,0 +1,9 @@
+#include "main.h"
+
+#define PAGE_SIZE 2048
+
+
+HAL_StatusTypeDef FLASH_Write_Page(uint32_t *Address, uint8_t *Data, int Data_size);
+HAL_StatusTypeDef FLASH_Write_Word(uint32_t Address, uint64_t Data);
+HAL_StatusTypeDef FLASH_Erase_App(void);
+uint8_t *FLASH_Read(uint32_t add);

Core/Inc/custom_receive_and_write.h

@@ -0,0 +1,20 @@
+#include "main.h"
+#include "ff.h"
+
+//#include "usart.h"
+#define sizebuff 16
+struct flags
+{
+	unsigned writting:1;
+};
+
+extern struct flags flags_UART_FATFS;
+
+FRESULT CreateAndOpenMessageFile(FIL *MessageFile, const TCHAR* path);
+FRESULT OpenMessageFile(FIL *MessageFile, const TCHAR* path);
+FRESULT WriteMessage(FIL *MessageFile, char *Message, UINT SizeOfMessage);
+FRESULT CloseMessageFile(FIL *MessageFile);
+void WriteFile(char *Data, int Num_of_Data);
+	
+void Check_USART(void);
+	

Core/Inc/custom_usart.h

@@ -0,0 +1,20 @@
+#include "main.h"
+
+#define __USER_LINKDMA(__HANDLE__, __PPP_DMA_FIELD__, __DMA_HANDLE__)               \
+                        do{                                                      \
+                              (__HANDLE__)->__PPP_DMA_FIELD__ = (__DMA_HANDLE__); \
+                              (__DMA_HANDLE__)->Parent = (__HANDLE__);} while(0U)
+
+struct UARTSettings
+{
+	USART_TypeDef *UARTx;
+	uint32_t UART_Speed;
+	GPIO_TypeDef *GPIOx;
+	uint16_t GPIO_PIN_RX;
+	uint16_t GPIO_PIN_TX;
+	DMA_Channel_TypeDef *DMAChannel; // DMAChannel = 0 if doesnt need
+};
+
+void User_UART_Init(UART_HandleTypeDef* huart, DMA_HandleTypeDef *DMAhuart, struct UARTSettings *uuart);
+void UART_GPIO_Init(GPIO_TypeDef *GPIOx, uint16_t GPIO_PIN_RX, uint16_t GPIO_PIN_TX);
+void UART_DMA_Init(UART_HandleTypeDef *huart, DMA_HandleTypeDef *hdma_rx, DMA_Channel_TypeDef *DMAhuart);

Core/Inc/dma.h

@@ -0,0 +1,52 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    dma.h
+  * @brief   This file contains all the function prototypes for
+  *          the dma.c file
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __DMA_H__
+#define __DMA_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+
+/* DMA memory to memory transfer handles -------------------------------------*/
+
+/* USER CODE BEGIN Includes */
+
+/* USER CODE END Includes */
+
+/* USER CODE BEGIN Private defines */
+
+/* USER CODE END Private defines */
+
+void MX_DMA_Init(void);
+
+/* USER CODE BEGIN Prototypes */
+
+/* USER CODE END Prototypes */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __DMA_H__ */
+

Core/Inc/gpio.h

@@ -0,0 +1,49 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    gpio.h
+  * @brief   This file contains all the function prototypes for
+  *          the gpio.c file
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __GPIO_H__
+#define __GPIO_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+
+/* USER CODE BEGIN Includes */
+
+/* USER CODE END Includes */
+
+/* USER CODE BEGIN Private defines */
+
+/* USER CODE END Private defines */
+
+void MX_GPIO_Init(void);
+
+/* USER CODE BEGIN Prototypes */
+
+/* USER CODE END Prototypes */
+
+#ifdef __cplusplus
+}
+#endif
+#endif /*__ GPIO_H__ */
+

Core/Inc/main.h

@@ -0,0 +1,71 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file           : main.h
+  * @brief          : Header for main.c file.
+  *                   This file contains the common defines of the application.
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __MAIN_H
+#define __MAIN_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal.h"
+
+/* Private includes ----------------------------------------------------------*/
+/* USER CODE BEGIN Includes */
+#include "boot_project_setup.h"
+#include "requester.h"
+
+/* USER CODE END Includes */
+
+/* Exported types ------------------------------------------------------------*/
+/* USER CODE BEGIN ET */
+
+/* USER CODE END ET */
+
+/* Exported constants --------------------------------------------------------*/
+/* USER CODE BEGIN EC */
+
+/* USER CODE END EC */
+
+/* Exported macro ------------------------------------------------------------*/
+/* USER CODE BEGIN EM */
+
+/* USER CODE END EM */
+
+/* Exported functions prototypes ---------------------------------------------*/
+void Error_Handler(void);
+void SystemClock_Config(void);
+/* USER CODE BEGIN EFP */
+
+/* USER CODE END EFP */
+
+/* Private defines -----------------------------------------------------------*/
+
+/* USER CODE BEGIN Private defines */
+
+/* USER CODE END Private defines */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MAIN_H */

Core/Inc/requester.h

@@ -0,0 +1,224 @@
+#ifndef _requester
+#define _requester
+#include "main.h"
+#include "can.h"
+#include "rtc.h"
+#include "tim.h"
+
+#define _DEMO
+
+#define ONLINE 1;
+#define OFFLINE 0;
+
+#define TIM_REQUESTER_Prescaler 64000
+
+//CAN Filter
+#define ID_MAIN_DEVICE 0x000
+#define CURRENT_ID_DEVICE 0x002
+#define CAN_IDE_32 0b00000100            // Для 32-х битного масштаба
+
+#define CAN_DATA_TYPE_FILTER 0x1F000000
+#define CAN_DEVICE_ID_FILTER 0x000000FF
+#define CAN_SENSOR_TYPE_FILTER 0x00F80000
+#define CAN_SENSOR_ID_FILTER 0x0007FF00
+
+
+void REQUESTER_Init(void);
+void REQUESTER_MainWhile(void);
+void Boot_SystemClock_Config(void);
+void REQUESTER_AnalogProcessing(void);
+void REQUESTER_BroadcastProcessing(void);
+void REQUESTER_DiscreticProcessing(void);
+void REQUESTER_ModbusProcessing(void);
+void REQUESTER_RTC_SYNC(uint8_t *data);
+void REQUESTER_Pulse_TIM_Handler(void);
+void Boot_SystemClock_Config(void);
+void REQUESTER_CAN_FILTERS(void);
+
+union Byte{
+	struct bitfield{
+		unsigned bit0:1;
+		unsigned bit1:1;
+		unsigned bit2:1;
+		unsigned bit3:1;
+		unsigned bit4:1;
+		unsigned bit5:1;
+		unsigned bit6:1;
+		unsigned bit7:1;
+	}Bitfield;
+	char AllBit;
+};
+
+_Bool IsLeapYear(uint8_t year);
+
+#define COUNT_OF_MODBUS_SECTIONS 1
+#define MODBUS_SECTION_MASK 0
+#define MODBUS_SECTION_FILTER 1
+
+#define SensorToModbusRegister(SensorType, SensorID) SensorType << 11 | SensorID
+#define HighByteOfWord(WORD) (WORD>>8)&0xFF
+#define LowByteOfWord(WORD) WORD&0xFF
+
+//Route mode
+#define ROUTE_MASTER 0
+#define ROUTE_SLAVE 1
+
+//Data Types
+#define DATA_TYPE_BROADCAST 0b0000
+#define DATA_TYPE_DISCRETE 0b0001
+#define DATA_TYPE_ANALOG 0b0010
+#define DATA_TYPE_MODBUS_COIL 0b0011
+#define DATA_TYPE_MODBUS_DISCRETE 0b0100
+#define DATA_TYPE_MODBUS_HOLDING 0b0101
+#define DATA_TYPE_MODBUS_INPUT 0b0110
+#define DATA_TYPE_ERROR 0b0111
+#define DATA_TYPE_PULSE 0b1111
+
+//Sensor Types for DATA_TYPE_BROADCAST
+#define SENSOR_TYPE_STATUS 0b00000
+#define SENSOR_TYPE_ONOFF 0b00001
+#define SENSOR_TYPE_RTCSETUP 0b00010
+
+//Sensor Types for DATA_TYPE_DISCRETE
+#define SENSOR_TYPE_ACCIDENT 0b00000
+#define SENSOR_TYPE_WARNING 0b00001
+#define SENSOR_TYPE_CONTROL_SIGNALS 0b00010
+#define SENSOR_TYPE_FLAGS 0b00011
+#define SENSOR_TYPE_RESET 0b00100
+#define SENSOR_TYPE_CHANGE_MODE 0b00101
+#define SENSOR_TYPE_REQUEST_LIST_OF_PARAMETERS 0b00110
+
+//Sensor Types for DATA_TYPE_ANALOG
+#define SENSOR_TYPE_UNIVERSAL 0b00000
+#define SENSOR_TYPE_U 0b00001
+#define SENSOR_TYPE_I 0b00010
+#define SENSOR_TYPE_T 0b00011
+
+//Error Code
+#define NONEXISTENT_ELEMENT 0x01
+
+#define HighIdFilter(x) x<<24
+
+
+struct controlflags{
+	unsigned IsPulse:1;
+	unsigned IsRtrMode:1;
+};
+
+//Device settings
+union ext_ID{
+	struct ext_ID_fields{
+		unsigned DeviceID:8;
+		unsigned SensorID:11;
+		unsigned SensorType:5;
+		unsigned DataType:4;
+		unsigned Route:1;
+	}Fields;
+	unsigned int BitAll:29;	
+};
+
+union ext_ID_Modbus{
+	struct ext_ID_Modbus_fields{
+		unsigned DeviceID:8;
+		unsigned CountReg:8;
+		unsigned StrAdr:8;
+		unsigned DataType:4;
+		unsigned Route;
+	}Fields;
+	unsigned int BitAll:29;	
+};
+
+struct device
+{
+	unsigned Status:1;
+	union ext_ID ExtID;
+	unsigned TimeFromLastPulse;
+	unsigned LastPulseStep;
+};
+
+struct data
+{
+	struct T_sens{
+		char info[256];
+		unsigned SensID;
+		unsigned AvrgValue;
+		unsigned LastTenValues[10];
+	}TS;
+	
+	struct U_sens{
+		char info[256];
+		unsigned SensID;
+		unsigned AvrgValue;
+		unsigned LastTenValues[10];
+	}Uu, Uv, Uw;
+	
+	struct I_sens{
+		char info[256];
+		unsigned SensID;
+		unsigned AvrgValue;
+		unsigned LastTenValues[10];		
+	}Iu, Iv, Iw;
+};
+
+struct received_request{
+	union ext_ID RequestedExtID;
+	unsigned RequestedDLC;
+	uint8_t RxData[8]; 
+	
+	//DATA_TYPE_DISCRETIC
+	union discreticflags{
+		struct discretictype{
+			unsigned Request_Accident:1;
+			unsigned Request_Warning:1;
+			unsigned Request_Control_Signals:1;
+			unsigned Request_Flags:1;
+			unsigned Request_Reset:1;
+			unsigned Request_List_of_Parameters:1;
+		}DiscreticType;
+		unsigned AllFlags:5;
+	}DiscreticFlags;
+	
+	//DATA_TYPE_BROADCAST
+	union broadcastflags{
+		struct broadcasttype{
+			unsigned Request_Status:1;
+			unsigned Request_OnOff:1;
+			unsigned Request_RTC_Setup:1;
+		}BroadcastType;
+		unsigned AllFlags:3;
+	}BroadcastFlags;
+	
+	//DATA_TYPE_ANALOG
+	union analogflags{
+		struct analogtype{
+			unsigned Request_Universal_Sens:1;
+			unsigned Request_U_Sens:1;
+			unsigned Request_I_Sens:1;
+			unsigned Request_T_Sens:1;
+		}AnalogType;
+		unsigned AllFlags:4;
+	}AnalogFlags;
+	
+	//DATA_TYPE_MODBUS
+	union modbusflags{
+		struct modbustype{
+			unsigned Coil:1;
+			unsigned Discrete:1;
+			unsigned Holding:1;
+			unsigned Input:1;
+		}ModbusType;
+		unsigned AllFlags:4;
+	}ModbusFlags;
+	
+	union sensor_To_Modbus{
+		struct modbus{
+			unsigned Count:8;
+			unsigned StrAdr:8;
+		}Modbus;
+		unsigned Sensor:16;
+	}SensorToModbus;
+	
+	unsigned ModbusFlag:1;
+};
+
+#endif

Core/Inc/rtc.h

@@ -0,0 +1,52 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    rtc.h
+  * @brief   This file contains all the function prototypes for
+  *          the rtc.c file
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __RTC_H__
+#define __RTC_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+
+/* USER CODE BEGIN Includes */
+
+/* USER CODE END Includes */
+
+extern RTC_HandleTypeDef hrtc;
+
+/* USER CODE BEGIN Private defines */
+
+/* USER CODE END Private defines */
+
+void MX_RTC_Init(void);
+
+/* USER CODE BEGIN Prototypes */
+
+/* USER CODE END Prototypes */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __RTC_H__ */
+

Core/Inc/sdio.h

@@ -0,0 +1,52 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    sdio.h
+  * @brief   This file contains all the function prototypes for
+  *          the sdio.c file
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __SDIO_H__
+#define __SDIO_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+
+/* USER CODE BEGIN Includes */
+
+/* USER CODE END Includes */
+
+extern SD_HandleTypeDef hsd;
+
+/* USER CODE BEGIN Private defines */
+
+/* USER CODE END Private defines */
+
+void MX_SDIO_SD_Init(void);
+
+/* USER CODE BEGIN Prototypes */
+
+/* USER CODE END Prototypes */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __SDIO_H__ */
+

Core/Inc/stm32f1xx_hal_conf.h

@@ -0,0 +1,391 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_conf.h
+  * @brief   HAL configuration file.
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2017 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_CONF_H
+#define __STM32F1xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+  * @brief This is the list of modules to be used in the HAL driver
+  */
+
+#define HAL_MODULE_ENABLED
+  /*#define HAL_ADC_MODULE_ENABLED   */
+/*#define HAL_CRYP_MODULE_ENABLED   */
+#define HAL_CAN_MODULE_ENABLED
+/*#define HAL_CAN_LEGACY_MODULE_ENABLED   */
+/*#define HAL_CEC_MODULE_ENABLED   */
+/*#define HAL_CORTEX_MODULE_ENABLED   */
+/*#define HAL_CRC_MODULE_ENABLED   */
+/*#define HAL_DAC_MODULE_ENABLED   */
+#define HAL_DMA_MODULE_ENABLED
+/*#define HAL_ETH_MODULE_ENABLED   */
+/*#define HAL_FLASH_MODULE_ENABLED   */
+#define HAL_GPIO_MODULE_ENABLED
+/*#define HAL_I2C_MODULE_ENABLED   */
+/*#define HAL_I2S_MODULE_ENABLED   */
+/*#define HAL_IRDA_MODULE_ENABLED   */
+/*#define HAL_IWDG_MODULE_ENABLED   */
+/*#define HAL_NOR_MODULE_ENABLED   */
+/*#define HAL_NAND_MODULE_ENABLED   */
+/*#define HAL_PCCARD_MODULE_ENABLED   */
+/*#define HAL_PCD_MODULE_ENABLED   */
+/*#define HAL_HCD_MODULE_ENABLED   */
+/*#define HAL_PWR_MODULE_ENABLED   */
+/*#define HAL_RCC_MODULE_ENABLED   */
+#define HAL_RTC_MODULE_ENABLED
+#define HAL_SD_MODULE_ENABLED
+/*#define HAL_MMC_MODULE_ENABLED   */
+/*#define HAL_SDRAM_MODULE_ENABLED   */
+/*#define HAL_SMARTCARD_MODULE_ENABLED   */
+/*#define HAL_SPI_MODULE_ENABLED   */
+/*#define HAL_SRAM_MODULE_ENABLED   */
+#define HAL_TIM_MODULE_ENABLED
+#define HAL_UART_MODULE_ENABLED
+/*#define HAL_USART_MODULE_ENABLED   */
+/*#define HAL_WWDG_MODULE_ENABLED   */
+
+#define HAL_CORTEX_MODULE_ENABLED
+#define HAL_DMA_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
+#define HAL_EXTI_MODULE_ENABLED
+#define HAL_GPIO_MODULE_ENABLED
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+
+/* ########################## Oscillator Values adaptation ####################*/
+/**
+  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSE is used as system clock source, directly or through the PLL).
+  */
+#if !defined  (HSE_VALUE)
+  #define HSE_VALUE    8000000U /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined  (HSE_STARTUP_TIMEOUT)
+  #define HSE_STARTUP_TIMEOUT    100U   /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+  * @brief Internal High Speed oscillator (HSI) value.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSI is used as system clock source, directly or through the PLL).
+  */
+#if !defined  (HSI_VALUE)
+  #define HSI_VALUE    8000000U /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+  * @brief Internal Low Speed oscillator (LSI) value.
+  */
+#if !defined  (LSI_VALUE)
+ #define LSI_VALUE               40000U    /*!< LSI Typical Value in Hz */
+#endif /* LSI_VALUE */                     /*!< Value of the Internal Low Speed oscillator in Hz
+                                                The real value may vary depending on the variations
+                                                in voltage and temperature. */
+
+/**
+  * @brief External Low Speed oscillator (LSE) value.
+  *        This value is used by the UART, RTC HAL module to compute the system frequency
+  */
+#if !defined  (LSE_VALUE)
+  #define LSE_VALUE    32768U /*!< Value of the External oscillator in Hz*/
+#endif /* LSE_VALUE */
+
+#if !defined  (LSE_STARTUP_TIMEOUT)
+  #define LSE_STARTUP_TIMEOUT    5000U   /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+   ===  you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+  * @brief This is the HAL system configuration section
+  */
+#define  VDD_VALUE                    3300U /*!< Value of VDD in mv */
+#define  TICK_INT_PRIORITY            15U    /*!< tick interrupt priority (lowest by default)  */
+#define  USE_RTOS                     0U
+#define  PREFETCH_ENABLE              1U
+
+#define  USE_HAL_ADC_REGISTER_CALLBACKS         0U /* ADC register callback disabled       */
+#define  USE_HAL_CAN_REGISTER_CALLBACKS         0U /* CAN register callback disabled       */
+#define  USE_HAL_CEC_REGISTER_CALLBACKS         0U /* CEC register callback disabled       */
+#define  USE_HAL_DAC_REGISTER_CALLBACKS         0U /* DAC register callback disabled       */
+#define  USE_HAL_ETH_REGISTER_CALLBACKS         0U /* ETH register callback disabled       */
+#define  USE_HAL_HCD_REGISTER_CALLBACKS         0U /* HCD register callback disabled       */
+#define  USE_HAL_I2C_REGISTER_CALLBACKS         0U /* I2C register callback disabled       */
+#define  USE_HAL_I2S_REGISTER_CALLBACKS         0U /* I2S register callback disabled       */
+#define  USE_HAL_MMC_REGISTER_CALLBACKS         0U /* MMC register callback disabled       */
+#define  USE_HAL_NAND_REGISTER_CALLBACKS        0U /* NAND register callback disabled      */
+#define  USE_HAL_NOR_REGISTER_CALLBACKS         0U /* NOR register callback disabled       */
+#define  USE_HAL_PCCARD_REGISTER_CALLBACKS      0U /* PCCARD register callback disabled    */
+#define  USE_HAL_PCD_REGISTER_CALLBACKS         0U /* PCD register callback disabled       */
+#define  USE_HAL_RTC_REGISTER_CALLBACKS         0U /* RTC register callback disabled       */
+#define  USE_HAL_SD_REGISTER_CALLBACKS          0U /* SD register callback disabled        */
+#define  USE_HAL_SMARTCARD_REGISTER_CALLBACKS   0U /* SMARTCARD register callback disabled */
+#define  USE_HAL_IRDA_REGISTER_CALLBACKS        0U /* IRDA register callback disabled      */
+#define  USE_HAL_SRAM_REGISTER_CALLBACKS        0U /* SRAM register callback disabled      */
+#define  USE_HAL_SPI_REGISTER_CALLBACKS         0U /* SPI register callback disabled       */
+#define  USE_HAL_TIM_REGISTER_CALLBACKS         0U /* TIM register callback disabled       */
+#define  USE_HAL_UART_REGISTER_CALLBACKS        0U /* UART register callback disabled      */
+#define  USE_HAL_USART_REGISTER_CALLBACKS       0U /* USART register callback disabled     */
+#define  USE_HAL_WWDG_REGISTER_CALLBACKS        0U /* WWDG register callback disabled      */
+
+/* ########################## Assert Selection ############################## */
+/**
+  * @brief Uncomment the line below to expanse the "assert_param" macro in the
+  *        HAL drivers code
+  */
+/* #define USE_FULL_ASSERT    1U */
+
+/* ################## Ethernet peripheral configuration ##################### */
+
+/* Section 1 : Ethernet peripheral configuration */
+
+/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
+#define MAC_ADDR0   2U
+#define MAC_ADDR1   0U
+#define MAC_ADDR2   0U
+#define MAC_ADDR3   0U
+#define MAC_ADDR4   0U
+#define MAC_ADDR5   0U
+
+/* Definition of the Ethernet driver buffers size and count */
+#define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
+#define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
+#define ETH_RXBUFNB                    8U       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */
+#define ETH_TXBUFNB                    4U       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
+
+/* Section 2: PHY configuration section */
+
+/* DP83848_PHY_ADDRESS Address*/
+#define DP83848_PHY_ADDRESS           0x01U
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
+#define PHY_RESET_DELAY                 0x000000FFU
+/* PHY Configuration delay */
+#define PHY_CONFIG_DELAY                0x00000FFFU
+
+#define PHY_READ_TO                     0x0000FFFFU
+#define PHY_WRITE_TO                    0x0000FFFFU
+
+/* Section 3: Common PHY Registers */
+
+#define PHY_BCR                         ((uint16_t)0x00)    /*!< Transceiver Basic Control Register   */
+#define PHY_BSR                         ((uint16_t)0x01)    /*!< Transceiver Basic Status Register    */
+
+#define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
+#define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
+#define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
+#define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
+#define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
+#define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
+#define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
+
+#define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
+#define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
+#define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
+
+/* Section 4: Extended PHY Registers */
+#define PHY_SR                          ((uint16_t)0x10U)    /*!< PHY status register Offset                      */
+
+#define PHY_SPEED_STATUS                ((uint16_t)0x0002U)  /*!< PHY Speed mask                                  */
+#define PHY_DUPLEX_STATUS               ((uint16_t)0x0004U)  /*!< PHY Duplex mask                                 */
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC                     0U
+
+/* Includes ------------------------------------------------------------------*/
+/**
+  * @brief Include module's header file
+  */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+#include "stm32f1xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+#include "stm32f1xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_EXTI_MODULE_ENABLED
+#include "stm32f1xx_hal_exti.h"
+#endif /* HAL_EXTI_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+#include "stm32f1xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+#include "stm32f1xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+#include "stm32f1xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
+  #include "Legacy/stm32f1xx_hal_can_legacy.h"
+#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
+
+#ifdef HAL_CEC_MODULE_ENABLED
+#include "stm32f1xx_hal_cec.h"
+#endif /* HAL_CEC_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+#include "stm32f1xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+#include "stm32f1xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+#include "stm32f1xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+#include "stm32f1xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+#include "stm32f1xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+#include "stm32f1xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+#include "stm32f1xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+#include "stm32f1xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+#include "stm32f1xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+#include "stm32f1xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+#include "stm32f1xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+#include "stm32f1xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_PCCARD_MODULE_ENABLED
+#include "stm32f1xx_hal_pccard.h"
+#endif /* HAL_PCCARD_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+#include "stm32f1xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+#include "stm32f1xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+#include "stm32f1xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+#include "stm32f1xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+#include "stm32f1xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+#include "stm32f1xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+#include "stm32f1xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+#include "stm32f1xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+#include "stm32f1xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+#include "stm32f1xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+#include "stm32f1xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+#ifdef HAL_MMC_MODULE_ENABLED
+#include "stm32f1xx_hal_mmc.h"
+#endif /* HAL_MMC_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef  USE_FULL_ASSERT
+/**
+  * @brief  The assert_param macro is used for function's parameters check.
+  * @param  expr If expr is false, it calls assert_failed function
+  *         which reports the name of the source file and the source
+  *         line number of the call that failed.
+  *         If expr is true, it returns no value.
+  * @retval None
+  */
+#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+void assert_failed(uint8_t* file, uint32_t line);
+#else
+#define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_CONF_H */
+

Core/Inc/stm32f1xx_it.h

@@ -0,0 +1,74 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_it.h
+  * @brief   This file contains the headers of the interrupt handlers.
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+ ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_IT_H
+#define __STM32F1xx_IT_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Private includes ----------------------------------------------------------*/
+/* USER CODE BEGIN Includes */
+
+/* USER CODE END Includes */
+
+/* Exported types ------------------------------------------------------------*/
+/* USER CODE BEGIN ET */
+
+/* USER CODE END ET */
+
+/* Exported constants --------------------------------------------------------*/
+/* USER CODE BEGIN EC */
+
+/* USER CODE END EC */
+
+/* Exported macro ------------------------------------------------------------*/
+/* USER CODE BEGIN EM */
+
+/* USER CODE END EM */
+
+/* Exported functions prototypes ---------------------------------------------*/
+void NMI_Handler(void);
+void HardFault_Handler(void);
+void MemManage_Handler(void);
+void BusFault_Handler(void);
+void UsageFault_Handler(void);
+void SVC_Handler(void);
+void DebugMon_Handler(void);
+void PendSV_Handler(void);
+void SysTick_Handler(void);
+void DMA1_Channel3_IRQHandler(void);
+void USB_HP_CAN1_TX_IRQHandler(void);
+void USB_LP_CAN1_RX0_IRQHandler(void);
+void CAN1_SCE_IRQHandler(void);
+void USART3_IRQHandler(void);
+void TIM8_UP_TIM13_IRQHandler(void);
+void TIM7_IRQHandler(void);
+void DMA2_Channel4_5_IRQHandler(void);
+/* USER CODE BEGIN EFP */
+
+/* USER CODE END EFP */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_IT_H */

Core/Inc/tim.h

@@ -0,0 +1,52 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    tim.h
+  * @brief   This file contains all the function prototypes for
+  *          the tim.c file
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __TIM_H__
+#define __TIM_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+
+/* USER CODE BEGIN Includes */
+
+/* USER CODE END Includes */
+
+extern TIM_HandleTypeDef htim7;
+
+/* USER CODE BEGIN Private defines */
+
+/* USER CODE END Private defines */
+
+void MX_TIM7_Init(void);
+
+/* USER CODE BEGIN Prototypes */
+
+/* USER CODE END Prototypes */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __TIM_H__ */
+

Core/Inc/usart.h

@@ -0,0 +1,52 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    usart.h
+  * @brief   This file contains all the function prototypes for
+  *          the usart.c file
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __USART_H__
+#define __USART_H__
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+
+/* USER CODE BEGIN Includes */
+//#include "custom_usart.h"
+/* USER CODE END Includes */
+
+extern UART_HandleTypeDef huart3;
+
+/* USER CODE BEGIN Private defines */
+
+/* USER CODE END Private defines */
+
+void MX_USART3_UART_Init(void);
+
+/* USER CODE BEGIN Prototypes */
+
+/* USER CODE END Prototypes */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __USART_H__ */
+

Core/Src/bootloader.c

@@ -0,0 +1,614 @@
+#include "bootloader.h"
+#include "custom_receive_and_write.h"
+
+extern FLASH_EraseInitTypeDef EraseInitStruct;
+
+struct flag FLAGS;
+struct Bootloader_Errors_Counters BOOTLOADER_ERRORS_COUNTERS;
+struct Bootloader_Errors BOOTLOADER_ERRORS;
+
+uint32_t app_current_add; // address for writing pages
+int cnt_tim_reset = 0; // WD Tim counter
+
+
+uint8_t ReceiveDataUART[4]; // buffer for CMD
+uint8_t Data2Write[PAGE_SIZE*2]; // DMA buffer for application
+uint8_t CAN_Data[8];
+
+
+CAN_TxHeaderTypeDef TxHeader;
+CAN_RxHeaderTypeDef RxHeader;
+uint32_t TxMailBox = 0; // num of used mail
+
+
+extern UART_HandleTypeDef huart_boot; // uart handler for boot uart
+extern DMA_HandleTypeDef hdma_usart_boot_rx; // dma handler for boot uart
+struct UARTSettings UARTSet; // settings for uart
+
+void Bootloader_Init(void)
+{	
+	HAL_Init();	
+	Boot_SystemClock_Config();
+	MX_DMA_Init();
+	//Если используется ЮСАРТ - инициализация
+#ifdef __USART_H__
+	
+	UARTSet.UARTx = UART_BOOT;
+	UARTSet.UART_Speed = UART_SPEED;
+	UARTSet.GPIOx = UART_PORT;
+	UARTSet.GPIO_PIN_RX = UART_PIN_RX;
+	UARTSet.GPIO_PIN_TX = UART_PIN_TX;
+	UARTSet.DMAChannel = DMA_UART_Channel;
+	
+	User_UART_Init(&huart_boot, &hdma_usart_boot_rx, &UARTSet);
+#endif
+
+	//Если используется SD-карта - инициализация
+#ifdef __SDIO_H__
+	BSP_SD_ITConfig();
+#endif
+	
+#ifdef __CAN_H__	
+  MX_CAN_Init();
+#endif
+	
+	//Инициализация светодиодов
+	MX_GPIO_Init();
+	MX_TIM7_Init();
+}
+
+HAL_StatusTypeDef res_hal;		
+void Bootloader_main(void) // main function, that defines bootloader behaviour
+{
+	/*
+	// Настройка доступной переферии с помощью define
+	Bootloader_Init();
+	*/
+	
+  /* START APPLICATION */
+	if (ReadKey() == BL_KEY_APP_WRITTEN)
+	{		
+		// jump to main app
+		//Задаётся адрес программы со смещением от начала вектора прерываний
+		uint32_t app_jump_adr;
+		app_jump_adr=*((volatile uint32_t*)(MAIN_APP_START_ADR+4));
+		void(*GoToApp)(void);
+		
+		//Деинициализация HAL
+		HAL_DeInit();
+		
+		GoToApp = (void (*) (void)) app_jump_adr;
+		//Перенос вектора прерываний на начало зашитой программы
+		__disable_irq();
+		__set_MSP(*((volatile uint32_t*)MAIN_APP_START_ADR));
+		__enable_irq();
+		//Переход к выполнению зашитой программы
+		GoToApp();
+	}
+	else  /* START PROGRAMMING MCU */
+	{
+		/* MCU Configuration for bootloader-------------------------------------------*/
+		/* Reset of all peripherals, Initializes the Flash BootloaderCMD and the Systick. */
+		Bootloader_Init();
+		FLAGS.InitOrWait = 0;
+		
+		// waif for commant for programming
+		do{
+			res_hal=HAL_UART_Receive_IT(&huart_boot, ReceiveDataUART, sizeof(ReceiveDataUART));
+			if(res_hal!=HAL_OK){
+				BOOTLOADER_ERRORS_COUNTERS.USART_RECEIVE++;
+				BOOTLOADER_ERRORS.USART_RECEIVE=1;
+			}
+		}while(res_hal!=HAL_OK); // if usart err - try start receive again
+		
+		HAL_CAN_Start(&hcan);
+		HAL_CAN_ActivateNotification(&hcan, CAN_IT_RX_FIFO0_MSG_PENDING);
+		
+CAN_FilterTypeDef canFilterConfig;
+canFilterConfig.FilterBank = 0;
+canFilterConfig.FilterMode = CAN_FILTERMODE_IDMASK;
+canFilterConfig.FilterScale = CAN_FILTERSCALE_32BIT;
+canFilterConfig.FilterIdHigh = 0x0000;
+canFilterConfig.FilterIdLow = 0x0000;
+canFilterConfig.FilterMaskIdHigh = 0x0000;
+canFilterConfig.FilterMaskIdLow = 0x0000;
+canFilterConfig.FilterFIFOAssignment = CAN_RX_FIFO0;
+canFilterConfig.FilterActivation = ENABLE;
+canFilterConfig.SlaveStartFilterBank = 14;
+HAL_CAN_ConfigFilter(&hcan, &canFilterConfig);
+		
+//		FLAGS.StartInit=1;			
+//		FLAGS.reInitMCU=1;
+//		FLAGS.BootloaderCMD = 2;
+		app_current_add = MAIN_APP_START_ADR;
+//		HAL_CAN_Start(&hcan);
+		/* Infinite loop */
+		while (1)
+		{					
+//			HAL_Delay(10);
+//			HAL_UART_Transmit(&huart_boot, (uint8_t *)"000000", 6, HAL_MAX_DELAY);
+			
+			// choose interface for programming
+			if (FLAGS.StartInit)
+			{
+				
+				
+				if (FLAGS.reInitMCU) // if its reInit request - erase outdate app
+				{
+					GPIOB->ODR^=0x2000;
+					res_hal=FLASH_Erase_App();
+					if(res_hal!=HAL_OK)
+					{
+						FLAGS.StartInit=1;
+						
+						BOOTLOADER_ERRORS.FLASH_ERASE = 1;
+						continue;
+					}
+					BOOTLOADER_ERRORS.FLASH_ERASE = 0;
+					GPIOB->ODR^=0x2000;
+					FLAGS.reInitMCU = 0;
+				}
+				FLAGS.StartInit = 0;
+				
+				HAL_UART_AbortReceive_IT(&huart_boot);
+				HAL_CAN_Stop(&hcan);
+				HAL_CAN_DeactivateNotification(&hcan, CAN_IT_RX_FIFO0_MSG_PENDING);
+				
+				switch ((int)FLAGS.BootloaderCMD) 
+				{
+					// UART
+					#ifdef __USART_H__
+					case 1:/* UART	*/
+						FLAGS.InitBootPeriph = 1;
+						// start receiving app.bin
+						res_hal = HAL_UART_Receive_DMA(&huart_boot, Data2Write, PAGE_SIZE*2);
+						if(res_hal!=HAL_OK)
+						{
+							FLAGS.StartInit=1;
+							BOOTLOADER_ERRORS_COUNTERS.USART_RECEIVE++;
+							BOOTLOADER_ERRORS.USART_RECEIVE = 1;
+							break;
+						}
+						// code of writing app in flash in callbacks functions:
+						// HAL_UART_RxHalfCpltCallback and HAL_UART_RxCpltCallback
+						break;
+					#endif
+					
+					#ifdef __CAN_H__
+					// CAN
+					case 2: /* CAN	*/ 
+						// activate can and start receiving app.bin
+						FLAGS.InitOrWait=1;
+						res_hal = HAL_CAN_Start(&hcan);
+						res_hal = HAL_CAN_ActivateNotification(&hcan, CAN_IT_RX_FIFO0_MSG_PENDING | CAN_IT_ERROR | CAN_IT_BUSOFF | CAN_IT_LAST_ERROR_CODE);
+						// code of writing app in flash in callback functions:
+						// HAL_CAN_RxFifo0MsgPendingCallback
+						break;
+					#endif
+					
+					// SD
+					#ifdef __SDIO_H__
+					case 3: /*  SD	*/ 
+						if (FLAGS.SDCardIn==0) // wait for sd-card
+						{
+							FLAGS.StartInit=1; // if there is no card, exit programmator and go in again
+							BOOTLOADER_ERRORS.SD_CARD_NOT_INSERTED = 1;
+							//Ошибка SD карты. Начать приём новой cmd
+							break;
+						}
+						HAL_Delay(100); // wait for inputting SD Card
+						if (FLAGS.SDCardIn==0)
+						{
+							FLAGS.StartInit=1;
+							BOOTLOADER_ERRORS.SD_CARD_NOT_INSERTED = 1;
+							break;
+						}
+						
+						FRESULT res_fresult;
+						SD_Programming(&res_fresult, &res_hal); // programming from sd card
+						// res_fresual - status for sd card read // res_hal - status for flash write
+						//Если всё удачно - выполнить код ниже. Если нет - StartInit = 1, break
+						if(res_fresult!=FR_OK || res_hal!=HAL_OK)
+						{
+							FLAGS.StartInit=1;
+							
+							if(res_fresult!=FR_OK){
+								BOOTLOADER_ERRORS_COUNTERS.SD_CARD_READ++;
+								BOOTLOADER_ERRORS.SD_CARD_READ = 1;
+							}
+							if(res_hal!=HAL_OK){
+								BOOTLOADER_ERRORS_COUNTERS.FLASH_WRITE++;
+								BOOTLOADER_ERRORS.FLASH_WRITE = 1;
+							}		
+							break;
+						}
+						// write Key: application in Flash, and reset MCU
+						{
+							ResetKey();
+							SetKey();
+							NVIC_SystemReset();
+						}// reset mcu
+						break;
+					#endif
+					
+					default: // if command is incorrect - wait CMD
+						BOOTLOADER_ERRORS_COUNTERS.CMD_INVALID++; // uncorrect command
+						BOOTLOADER_ERRORS.CMD_INVALID=1;
+						do
+						{
+							res_hal=HAL_UART_Receive_IT(&huart_boot, ReceiveDataUART, sizeof(ReceiveDataUART));
+							if(res_hal!=HAL_OK){
+								BOOTLOADER_ERRORS_COUNTERS.USART_RECEIVE++; // err when initialize uart
+								BOOTLOADER_ERRORS.USART_RECEIVE=1;}
+						}while(res_hal!=HAL_OK);
+						HAL_CAN_Start(&hcan);
+						HAL_CAN_ActivateNotification(&hcan, CAN_IT_RX_FIFO0_MSG_PENDING);
+				}
+			}
+			
+//	TxHeader.StdId = 0x200; // ID OF MESSAGE
+//	TxHeader.ExtId = 0; // STANDART FRAME (NOT EXTENTED)
+//	TxHeader.RTR = CAN_RTR_DATA; // TRANSMIT DATA OR 
+//	TxHeader.IDE = CAN_ID_STD; // STANDART FRAME
+//	TxHeader.DLC = 8; // DATA SIZE
+//	TxHeader.TransmitGlobalTime = DISABLE; //THIS MODE IS NOT USED, SO DISABLE
+//	uint8_t asd[8] = "ABCDEFGL";
+//	while(HAL_CAN_GetTxMailboxesFreeLevel(&hcan) == 0); // wait for free mail box
+//		res_hal =	HAL_CAN_AddTxMessage(&hcan, &TxHeader, asd, &TxMailBox); // add to mail for transmit
+//	HAL_Delay(1000);
+			
+			
+		}
+	}
+}
+
+
+
+
+void SD_Programming(FRESULT *res_fresult, HAL_StatusTypeDef *res_hal)
+{					
+	// init peripth
+	MX_FATFS_Init();
+	MX_SDIO_SD_Init();
+	FIL MFile;
+	int SizeApp;
+	int AppCount;
+	
+	// mount disk
+	uint8_t MOUNT=1;	
+	*res_fresult = f_mount(&SDFatFS, (TCHAR const*)SDPath, 1);
+	if(*res_fresult != FR_OK) return;
+
+	// name of the application file
+	static char path[8] = "app.bin";
+	path[7] = '\0';
+	
+	
+	// OPEN AND READ
+	*res_fresult = f_open(&MFile, (const TCHAR*)path, FA_READ);	
+	if (*res_fresult == FR_OK)
+	{
+		SizeApp = MFile.fsize;
+		AppCount = 0; // counter of written bytes
+		
+		
+		unsigned int bytesRead;
+		// reading and writing two pages
+		while(SizeApp - AppCount >= PAGE_SIZE*2) // read while count of rest bytes more than size of two pages
+		{
+			*res_fresult = f_read(&MFile, Data2Write, PAGE_SIZE*2, &bytesRead);
+			
+			if(*res_fresult != FR_OK) return;
+			
+			AppCount += PAGE_SIZE*2;
+			
+			*res_hal = FLASH_Write_Page(&app_current_add, Data2Write, PAGE_SIZE*2);
+			
+			if(*res_hal != HAL_OK) return;
+			
+			GPIOB->ODR^=0x2000; // indicate written two pages
+		}
+		// reading and writing rest bytes (less than two pages)
+		if(SizeApp != AppCount)
+		{
+			int NumOfLastBytes = SizeApp - AppCount;
+			
+			*res_fresult = f_read(&MFile, Data2Write, NumOfLastBytes, &bytesRead);
+			
+			if(*res_fresult != FR_OK) return;
+			
+			AppCount += PAGE_SIZE*2;
+			
+			*res_hal = FLASH_Write_Page(&app_current_add, Data2Write, NumOfLastBytes);
+			
+			if(*res_hal != HAL_OK) return;
+			
+			GPIOB->ODR^=0x2000;
+		}
+		
+		*res_fresult = f_close(&MFile); // indicate written two pages
+	}
+}
+
+void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart) // writing first half of dma buffer (1 page)
+{	
+	if (huart->Instance == UART_BOOT)
+	{
+		if (FLAGS.InitOrWait)
+		{		
+			HAL_StatusTypeDef res_hal;
+			
+			if (FLAGS.InitBootPeriph) // if its first received page
+			{
+				//HAL_TIM_Base_Start_IT(&htim_boot); 	// start "wd" timer
+				FLAGS.InitBootPeriph = 0;						// 5 sec silent on RX - mcu reset
+			}
+			
+			res_hal = FLASH_Write_Page(&app_current_add, Data2Write, PAGE_SIZE);
+			if (res_hal != HAL_OK)
+			{
+				BOOTLOADER_ERRORS_COUNTERS.FLASH_WRITE++; // err when initialize uart
+				BOOTLOADER_ERRORS.FLASH_WRITE=1;
+			}
+	//		HAL_UART_DMAStop(&huart_boot);
+	//		HAL_UART_AbortReceive_IT(&huart_boot);
+	//		HAL_UART_AbortReceive(&huart_boot);
+			
+			FLAGS.HalfOfWrite = 1; // switch unwritten half of DMA buffer
+			
+			cnt_tim_reset = 0; // upd WD Tim
+			GPIOB->ODR^=0x2000; // indicate written page	
+		}
+	}
+}	
+
+void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart)  // writing second half of dma buffer (1 page)
+{
+if (huart->Instance == UART_BOOT)
+{
+	if (FLAGS.InitOrWait == 0) // if its wait mode (not writting app)
+	{
+		// set Init mode, start WDTim after receiving first page
+		Check_CMD_USART(ReceiveDataUART); // check received uart data
+		FLAGS.InitOrWait = 1;
+		FLAGS.StartInit = 1;
+		FLAGS.InitBootPeriph = 1;
+		app_current_add = MAIN_APP_START_ADR; // set adress for app		
+	}
+	else
+	{	
+		HAL_StatusTypeDef res_hal;
+		res_hal = FLASH_Write_Page(&app_current_add, Data2Write+PAGE_SIZE, PAGE_SIZE);
+		if (res_hal != HAL_OK)
+		{
+			BOOTLOADER_ERRORS_COUNTERS.FLASH_WRITE++; // err when initialize uart
+			BOOTLOADER_ERRORS.FLASH_WRITE=1;
+		}
+		
+		FLAGS.HalfOfWrite = 0; // switch unwritten half of DMA buffer
+		
+		cnt_tim_reset = 0; // upd WD Tim
+		GPIOB->ODR^=0x2000; // indicate written page
+	}
+}
+}
+
+
+uint32_t temp_app_cur_add;
+int app_size;
+/*void HAL_CAN_RxFifo0MsgPendingCallback(CAN_HandleTypeDef *hcan)
+{
+	
+	if(HAL_CAN_GetRxMessage(hcan, CAN_RX_FIFO0, &RxHeader, CAN_Data) == HAL_OK)
+	{	
+#ifdef _CAN_PUSH_ID_TO_ADDR_		
+		if(FLAGS.InitOrWait)
+		{	// if its 1 - Init: writting app.bin in flash
+			temp_app_cur_add = app_current_add+(RxHeader.ExtId&(0x0000FFFF));
+		
+			FLASH_Write_Page(&temp_app_cur_add, CAN_Data, 8);
+			app_size-=8; // decrease app_size 
+			if (app_size<=0) // when its gone - reset system and go to the app
+			{
+				__ASM("");
+				NVIC_SystemReset();
+			}
+		}
+		else
+	{	// if its 0 - Wait: parsing address to writting and size of app.bin
+		app_current_add = Data2Write[0]<<24 | Data2Write[1]<<16 | Data2Write[2]<<8 | Data2Write[3];
+		app_size = Data2Write[4]<<24 | Data2Write[5]<<16 | Data2Write[6]<<8 | Data2Write[7];
+		FLAGS.InitOrWait = 1; // switch to firmware (init)
+	}
+#endif
+		if(FLAGS.InitOrWait)
+		{
+			if (FLAGS.InitBootPeriph) // if its first received page
+			{
+				HAL_TIM_Base_Start_IT(&htim_boot); 	// start "wd" timer
+				FLAGS.InitBootPeriph = 0;						// 5 sec silent on RX - mcu reset
+			}
+			FLASH_Write_Page(&app_current_add, CAN_Data, 8);
+			cnt_tim_reset=0;
+		}
+		else
+		{
+
+		app_current_add = MAIN_APP_START_ADR; // set adress for app		
+			Check_CMD_USART(CAN_Data);
+			FLAGS.InitBootPeriph=1;		
+			FLAGS.InitOrWait = 1;
+			FLAGS.StartInit = 1;
+		}
+	}
+}
+
+*/
+void HAL_CAN_ErrorCallback(CAN_HandleTypeDef *hcan)
+{
+	uint32_t er;
+	er = HAL_CAN_GetError(hcan);
+		__ASM("");	
+}
+void Bootloader_TIM_Handler(void) // reset mcu after writing application is done
+{ // add this to the TIM handler that is used (TIMx is seting up in project_setup.h)
+	HAL_StatusTypeDef res_fresult;
+	cnt_tim_reset++;
+	if (cnt_tim_reset > 5) // writing is done if there is silence on Rx for 5 second
+	{
+		if(FLAGS.BootloaderCMD==1)
+		{
+			FLAGS.InitMCUReady = 1;
+			ResetKey();
+			SetKey(); // write key for going to application
+			int NumOfLastBytes = (PAGE_SIZE - DMA1_Channel3->CNDTR%PAGE_SIZE); // read size of new data in dma buffer
+			if (NumOfLastBytes != 0)
+			{			
+				res_fresult = FLASH_Write_Page(&app_current_add, Data2Write+PAGE_SIZE*FLAGS.HalfOfWrite, NumOfLastBytes); // writing last data
+			}
+			NVIC_SystemReset(); // reset mcu
+		}
+		else if(FLAGS.BootloaderCMD==2)
+		{
+			FLAGS.InitMCUReady = 1;
+			ResetKey();
+			SetKey();
+			NVIC_SystemReset();
+		}
+	}
+}
+
+
+void Check_CMD_USART(uint8_t *DataUART) // choose CMD (interface)
+{	// 4 byte: 0xFF - erase app, else - just write app
+	//USART
+	if ((DataUART[0]|
+				DataUART[1]<<8|
+				DataUART[2]<<16)	== 0xFFFFFF)
+	{
+		FLAGS.BootloaderCMD = 1;
+	}
+	//CAN
+	else if ((DataUART[0]|
+				DataUART[1]<<8|
+				DataUART[2]<<16)	== 0xAAAFFF)
+	{
+		FLAGS.BootloaderCMD = 2;
+	}
+	//SDIO
+	else if ((DataUART[0]|
+				DataUART[1]<<8|
+				DataUART[2]<<16)	== 0xAAFAFF)
+	{
+		FLAGS.BootloaderCMD = 3;
+		BSP_SD_DetectIT();
+	}
+	if (DataUART[3]== 0xFF)
+	{
+		FLAGS.reInitMCU = 1;
+	}
+	else
+	{
+		FLAGS.reInitMCU = 0;
+	}
+		
+}
+
+
+
+
+// reset/set key function
+void SetKey(void)
+{	
+	HAL_FLASH_Unlock();
+	
+	HAL_FLASH_Program(FLASH_TYPEPROGRAM_WORD, BOOTLOADER_KEY_ADR, BL_KEY_APP_WRITTEN);
+	
+	HAL_FLASH_Lock();	
+}
+
+uint32_t ReadKey(void)
+{	
+	return (*(__IO uint32_t*)BOOTLOADER_KEY_ADR);
+}
+
+void ResetKey(void)
+{	
+	HAL_FLASH_Unlock();
+	uint32_t PageError = 0x00;
+	
+	EraseInitStruct.TypeErase   = FLASH_TYPEERASE_PAGES;// erase pages
+	EraseInitStruct.PageAddress = BOOTLOADER_KEY_ADR;   //address
+	EraseInitStruct.NbPages     = 0x01;// num of erased  pages
+	
+	HAL_FLASHEx_Erase(&EraseInitStruct, &PageError);
+	HAL_FLASH_Lock();
+	
+}
+
+
+HAL_StatusTypeDef BSP_SD_ITConfig(void)
+{ 
+  /* Code to be updated by the user or replaced by one from the FW pack (in a stmxxxx_sd.c file) */
+  GPIO_InitTypeDef gpio_init_structure;
+
+  /* Configure Interrupt mode for SD detection pin */  
+  gpio_init_structure.Pin = SDIO_SDCard_In_PIN;
+  gpio_init_structure.Pull = GPIO_PULLUP;
+  gpio_init_structure.Speed = GPIO_SPEED_HIGH;
+  gpio_init_structure.Mode = GPIO_MODE_IT_RISING_FALLING;
+  HAL_GPIO_Init(SDIO_SDCard_In_PORT, &gpio_init_structure);
+
+  /* Enable and set SD detect EXTI Interrupt to the lowest priority */
+  HAL_NVIC_SetPriority((SDIO_SDCard_In_IRQn), 0x00, 0x00);
+  HAL_NVIC_EnableIRQ((SDIO_SDCard_In_IRQn));
+
+  return HAL_OK;
+//  return (uint8_t)0;
+}
+
+
+void BSP_SD_DetectIT(void)
+{ // add this to the EXTI handler that is used (EXTIx (GPIO_PIN_x) is seting up in project_setup.h)
+	
+	if(SDIO_SDCard_In_PORT->IDR&SDIO_SDCard_In_PIN)
+		FLAGS.SDCardIn = 0;
+	else
+		FLAGS.SDCardIn = 1;
+}
+
+
+void Boot_SystemClock_Config(void)
+{
+  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
+  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
+
+  /** Initializes the RCC Oscillators according to the specified parameters
+  * in the RCC_OscInitTypeDef structure.
+  */
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
+  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI_DIV2;
+  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL16;
+  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
+  {
+    Error_Handler();
+  }
+
+  /** Initializes the CPU, AHB and APB buses clocks
+  */
+  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
+                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+
+  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  HAL_RCC_MCOConfig(RCC_MCO, RCC_MCO1SOURCE_PLLCLK, RCC_MCODIV_1);
+}

Core/Src/can.c

@@ -0,0 +1,131 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    can.c
+  * @brief   This file provides code for the configuration
+  *          of the CAN instances.
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+/* Includes ------------------------------------------------------------------*/
+#include "can.h"
+
+/* USER CODE BEGIN 0 */
+
+/* USER CODE END 0 */
+
+CAN_HandleTypeDef hcan;
+
+/* CAN init function */
+void MX_CAN_Init(void)
+{
+
+  /* USER CODE BEGIN CAN_Init 0 */
+
+  /* USER CODE END CAN_Init 0 */
+
+  /* USER CODE BEGIN CAN_Init 1 */
+
+  /* USER CODE END CAN_Init 1 */
+  hcan.Instance = CAN1;
+  hcan.Init.Prescaler = 2;
+  hcan.Init.Mode = CAN_MODE_NORMAL;
+  hcan.Init.SyncJumpWidth = CAN_SJW_1TQ;
+  hcan.Init.TimeSeg1 = CAN_BS1_13TQ;
+  hcan.Init.TimeSeg2 = CAN_BS2_2TQ;
+  hcan.Init.TimeTriggeredMode = DISABLE;
+  hcan.Init.AutoBusOff = ENABLE;
+  hcan.Init.AutoWakeUp = DISABLE;
+  hcan.Init.AutoRetransmission = DISABLE;
+  hcan.Init.ReceiveFifoLocked = DISABLE;
+  hcan.Init.TransmitFifoPriority = ENABLE;
+  if (HAL_CAN_Init(&hcan) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN CAN_Init 2 */
+
+  /* USER CODE END CAN_Init 2 */
+
+}
+
+void HAL_CAN_MspInit(CAN_HandleTypeDef* canHandle)
+{
+
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+  if(canHandle->Instance==CAN1)
+  {
+  /* USER CODE BEGIN CAN1_MspInit 0 */
+
+  /* USER CODE END CAN1_MspInit 0 */
+    /* CAN1 clock enable */
+    __HAL_RCC_CAN1_CLK_ENABLE();
+
+    __HAL_RCC_GPIOA_CLK_ENABLE();
+    /**CAN GPIO Configuration
+    PA11     ------> CAN_RX
+    PA12     ------> CAN_TX
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_11;
+    GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_12;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+    /* CAN1 interrupt Init */
+    HAL_NVIC_SetPriority(USB_HP_CAN1_TX_IRQn, 0, 0);
+    HAL_NVIC_EnableIRQ(USB_HP_CAN1_TX_IRQn);
+    HAL_NVIC_SetPriority(USB_LP_CAN1_RX0_IRQn, 0, 0);
+    HAL_NVIC_EnableIRQ(USB_LP_CAN1_RX0_IRQn);
+    HAL_NVIC_SetPriority(CAN1_SCE_IRQn, 0, 0);
+    HAL_NVIC_EnableIRQ(CAN1_SCE_IRQn);
+  /* USER CODE BEGIN CAN1_MspInit 1 */
+
+  /* USER CODE END CAN1_MspInit 1 */
+  }
+}
+
+void HAL_CAN_MspDeInit(CAN_HandleTypeDef* canHandle)
+{
+
+  if(canHandle->Instance==CAN1)
+  {
+  /* USER CODE BEGIN CAN1_MspDeInit 0 */
+
+  /* USER CODE END CAN1_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_CAN1_CLK_DISABLE();
+
+    /**CAN GPIO Configuration
+    PA11     ------> CAN_RX
+    PA12     ------> CAN_TX
+    */
+    HAL_GPIO_DeInit(GPIOA, GPIO_PIN_11|GPIO_PIN_12);
+
+    /* CAN1 interrupt Deinit */
+    HAL_NVIC_DisableIRQ(USB_HP_CAN1_TX_IRQn);
+    HAL_NVIC_DisableIRQ(USB_LP_CAN1_RX0_IRQn);
+    HAL_NVIC_DisableIRQ(CAN1_SCE_IRQn);
+  /* USER CODE BEGIN CAN1_MspDeInit 1 */
+
+  /* USER CODE END CAN1_MspDeInit 1 */
+  }
+}
+
+/* USER CODE BEGIN 1 */
+
+/* USER CODE END 1 */

Core/Src/custom_flash.c

@@ -0,0 +1,94 @@
+#include "custom_flash.h"
+#include "bootloader.h"
+FLASH_EraseInitTypeDef EraseInitStruct;
+//uint32_t PAGE_OFFSET = ((uint32_t)((4-1) * 0x0400));
+uint32_t PAGE_NUMB = 127;
+
+
+
+
+uint8_t *FLASH_Read(uint32_t add)
+{
+	return (uint8_t *)add;
+}
+
+HAL_StatusTypeDef FLASH_Write_Word(uint32_t Address, uint64_t Data) //Куда записывать
+{
+	HAL_StatusTypeDef res;
+	
+	res = HAL_FLASH_Unlock();
+	
+	if (res != HAL_OK) return res;
+	
+	res = HAL_FLASH_Program(FLASH_TYPEPROGRAM_WORD, Address, (uint32_t)(Data));
+	
+	if (res != HAL_OK) return res;
+
+	res = HAL_FLASH_Lock();
+	
+	return res;
+}
+uint32_t word_data;
+
+
+
+
+HAL_StatusTypeDef FLASH_Write_Page(uint32_t *Address, uint8_t *Data, int Data_size)
+{
+		//GPIOB->ODR^=(0x2000);
+//		GPIOB->ODR|=0x4000;
+	
+	HAL_StatusTypeDef res;
+	int data_cnt = 0;
+	uint32_t adr;
+	
+	
+	res = HAL_FLASH_Unlock();
+	
+	if (res != HAL_OK) return res;
+	
+	for (adr = *Address; adr < *Address + Data_size; adr = adr+4)
+	{
+		word_data = (
+				Data[data_cnt]|
+				Data[data_cnt+1]<<8|
+				Data[data_cnt+2]<<16|
+				Data[data_cnt+3]<<24);
+		
+		res = HAL_FLASH_Program(FLASH_TYPEPROGRAM_WORD, adr, word_data);
+		
+		if (res != HAL_OK) return res;
+		
+		data_cnt +=4;
+	}
+	
+	*Address += Data_size;
+	res = HAL_FLASH_Lock();
+	
+	return res;
+}
+
+
+
+HAL_StatusTypeDef FLASH_Erase_App(void) //
+{
+	HAL_StatusTypeDef res;
+	uint32_t PageError = 0x00;
+	
+	res = HAL_FLASH_Unlock();
+	
+	if (res != HAL_OK) return res;
+	
+	EraseInitStruct.TypeErase   = FLASH_TYPEERASE_PAGES;// erase pages
+	EraseInitStruct.Banks = 1;
+	EraseInitStruct.PageAddress = MAIN_APP_START_ADR;   //address
+	EraseInitStruct.NbPages     = MAIN_APP_NUM_OF_PAGE;// num of erased  pages
+	
+	res = HAL_FLASHEx_Erase(&EraseInitStruct, &PageError);
+	
+	if (res != HAL_OK) return res;
+	
+	res = HAL_FLASH_Lock();
+	
+	return res;
+}

Core/Src/custom_receive_and_write.c

@@ -0,0 +1,105 @@
+#include "custom_receive_and_write.h"
+extern UART_HandleTypeDef huart3;
+struct flags flags_UART_FATFS;
+extern FIL SDFile;
+uint8_t bytescnt;
+char Char_Shift = 0x41;
+FIL MFile;
+
+uint8_t Message[sizebuff] = "";
+
+uint8_t path_uart[5] = "A.txt";
+
+
+//void MountSD(void)
+//{
+//	if((f_mount(&SDFatFS, (TCHAR const*)SDPath, MOUNT)) ==FR_OK)
+//  {
+//		for (int i=0;i<5;i++)
+//			{
+//				GPIOB->ODR^=1<<14;
+//				HAL_Delay(500);
+//			}
+//			 GPIOB->ODR&=~(1<<14);  \
+//	}
+//}
+
+FRESULT CreateAndOpenMessageFile(FIL *MessageFile, const TCHAR* Path)
+{
+	return f_open(MessageFile, Path, FA_WRITE | FA_CREATE_ALWAYS);
+}
+
+FRESULT OpenMessageFile(FIL *MessageFile, const TCHAR* Path)
+{
+	return f_open(MessageFile, Path, FA_READ);
+}
+
+FRESULT WriteMessage(FIL *MessageFile, char *Message, UINT SizeOfMessage)
+{
+	FRESULT ResultOfOperation;
+	uint32_t WrittenBytes;
+	ResultOfOperation = f_lseek(MessageFile,f_size(MessageFile));
+	ResultOfOperation = f_write(MessageFile, Message, SizeOfMessage, &WrittenBytes);
+	if (WrittenBytes!=SizeOfMessage) return FR_INVALID_PARAMETER;
+	//GPIOB->ODR^=0xf000;
+	return ResultOfOperation;
+}
+
+FRESULT CloseMessageFile(FIL *MessageFile)
+{
+	return f_close(MessageFile);	
+}
+
+void WriteFile(char *Data, int Num_of_Data)
+{ 
+	static int FileOpen = 0;
+	OpenMessageFile(&MFile, (const TCHAR*)path_uart);
+	WriteMessage(&MFile, Data, Num_of_Data);
+	CloseMessageFile(&MFile);
+//	Char_Shift++;
+//	path_uart[0] = (char)Char_Shift;
+}
+
+void Check_USART(void)
+{		
+	uint8_t res;
+
+	static FIL MessageFile;
+
+	if (flags_UART_FATFS.writting==0)
+	{		switch((int)Message[0])
+		{
+			case 1:			
+			flags_UART_FATFS.writting = 1;
+			Message[bytescnt] = '\0';
+			res = CreateAndOpenMessageFile(&MessageFile, (const TCHAR*)(Message+1)); 
+			break;
+			case 2:		
+			flags_UART_FATFS.writting = 1;
+			res = OpenMessageFile(&MessageFile, (const TCHAR*)path_uart);	
+			break;	
+		}	
+
+	}
+	else
+	{		
+		if (Message[0] == 0x03)
+		{
+			flags_UART_FATFS.writting = 0;
+			res = CloseMessageFile(&MessageFile);
+		}		
+		else 
+		{
+			res = WriteMessage(&MessageFile, (char *)Message, bytescnt);
+		}
+	}
+	HAL_UART_AbortReceive_IT(&huart3);
+	HAL_UART_Receive_IT(&huart3, Message, sizeof(Message));
+	
+
+	bytescnt = 0;
+	for(int i = 0; i<sizebuff; i++)
+	{
+		Message[i] = 0x00;
+	}
+}

Core/Src/custom_usart.c

@@ -0,0 +1,125 @@
+#ifndef _CUSTOM_USART_
+#define _CUSTOM_USART_
+
+#include "custom_usart.h"
+
+UART_HandleTypeDef huart_boot;
+DMA_HandleTypeDef hdma_usart_boot_rx;
+
+// CUSTOM UART INIT
+// DMA INIT (RCC, NVIC) SHOULD BE ADDED IN DMA.C
+void User_UART_Init(UART_HandleTypeDef* huart, DMA_HandleTypeDef *DMAhuart, struct UARTSettings *uuart)
+{ // function takes uart handler, dma handler and setting structure for init
+	
+	// get setting for uart from UARTSettings structure
+	huart->Instance = uuart->UARTx;
+  huart->Init.BaudRate = uuart->UART_Speed;
+	
+	// everything else is default (for now, maybe this settings would be added in UARTSettings structure later)
+  huart->Init.WordLength = UART_WORDLENGTH_8B;
+  huart->Init.StopBits = UART_STOPBITS_1;
+  huart->Init.Parity = UART_PARITY_NONE;
+  huart->Init.Mode = UART_MODE_TX_RX;
+  huart->Init.HwFlowCtl = UART_HWCONTROL_NONE;
+  huart->Init.OverSampling = UART_OVERSAMPLING_16;
+  if (HAL_UART_Init(huart) != HAL_OK)
+  {
+    Error_Handler();
+  }
+	
+	// init gpio from UARTSettings structure
+	UART_GPIO_Init(uuart->GPIOx, uuart->GPIO_PIN_RX, uuart->GPIO_PIN_TX);
+	// init dma from UARTSettings structure if need
+	if (uuart->DMAChannel != 0)
+		UART_DMA_Init(huart, DMAhuart, uuart->DMAChannel);
+}
+
+
+void UART_GPIO_Init(GPIO_TypeDef *GPIOx, uint16_t GPIO_PIN_RX, uint16_t GPIO_PIN_TX)
+{ // function takes port and pins (for rx and tx)
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+	
+	// choose port for enable clock
+	if (GPIOx==GPIOA)
+		__HAL_RCC_GPIOA_CLK_ENABLE();
+	else if (GPIOx==GPIOB)
+		__HAL_RCC_GPIOB_CLK_ENABLE();
+	else if (GPIOx==GPIOC)
+		__HAL_RCC_GPIOC_CLK_ENABLE();
+	else if (GPIOx==GPIOD)
+		__HAL_RCC_GPIOD_CLK_ENABLE();
+	
+// USART3 GPIO Configuration
+//GPIO_PIN_TX ------> USART_TX
+	GPIO_InitStruct.Pin = GPIO_PIN_TX;
+	GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+	HAL_GPIO_Init(GPIOx, &GPIO_InitStruct);
+
+//	GPIO_PIN_RX ------> USART_RX	
+	GPIO_InitStruct.Pin = GPIO_PIN_RX;
+	GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+	GPIO_InitStruct.Pull = GPIO_NOPULL;
+	HAL_GPIO_Init(GPIOx, &GPIO_InitStruct);
+}
+
+
+void UART_DMA_Init(UART_HandleTypeDef *huart, DMA_HandleTypeDef *hdma_rx, DMA_Channel_TypeDef *DMAhuart)
+{ // function takes uart and dma handlers and dmachannel for uart
+	// for now only dma rx is supported, tx maybe later if needed
+	
+	/* USART3 DMA Init */
+	/* USART3_RX Init */
+	hdma_rx->Instance = DMAhuart;
+	hdma_rx->Init.Direction = DMA_PERIPH_TO_MEMORY;
+	hdma_rx->Init.PeriphInc = DMA_PINC_DISABLE;
+	hdma_rx->Init.MemInc = DMA_MINC_ENABLE;
+	hdma_rx->Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
+	hdma_rx->Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
+	hdma_rx->Init.Mode = DMA_CIRCULAR;
+	hdma_rx->Init.Priority = DMA_PRIORITY_LOW;
+	if (HAL_DMA_Init(hdma_rx) != HAL_OK)
+	{
+		Error_Handler();
+	}
+
+	__USER_LINKDMA(huart,hdmarx,hdma_rx); 
+	// __USER_LINKDMA is need because __HAL_LINKDMA is written for global defined hdma_rx
+	// so you get error because hal uses . insted of ->
+}
+
+
+
+void HAL_UART_MspInit(UART_HandleTypeDef* huart) // redefine hal function
+{ // left only rcc and interrupt init for USART_1,2,3 (maybe UART_4,5 need to be added)
+	// GPIO and DMA init was move to their own functions
+  if(huart->Instance==USART3)
+  {
+	/* USART3 clock enable */
+	__HAL_RCC_USART3_CLK_ENABLE();
+	
+	/* USART3 interrupt Init */
+	HAL_NVIC_SetPriority(USART3_IRQn, 0, 0);
+  HAL_NVIC_EnableIRQ(USART3_IRQn);
+  }
+	else if(huart->Instance==USART2)
+  {
+	/* USART3 clock enable */
+	__HAL_RCC_USART2_CLK_ENABLE();
+	
+	/* USART3 interrupt Init */
+	HAL_NVIC_SetPriority(USART2_IRQn, 0, 0);
+  HAL_NVIC_EnableIRQ(USART2_IRQn);
+  }
+	else if(huart->Instance==USART1)
+  {
+	/* USART3 clock enable */
+	__HAL_RCC_USART1_CLK_ENABLE();
+	
+	/* USART3 interrupt Init */
+	HAL_NVIC_SetPriority(USART1_IRQn, 0, 0);
+  HAL_NVIC_EnableIRQ(USART1_IRQn);
+  }
+}
+
+#endif

Core/Src/dma.c

@@ -0,0 +1,59 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    dma.c
+  * @brief   This file provides code for the configuration
+  *          of all the requested memory to memory DMA transfers.
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Includes ------------------------------------------------------------------*/
+#include "dma.h"
+
+/* USER CODE BEGIN 0 */
+
+/* USER CODE END 0 */
+
+/*----------------------------------------------------------------------------*/
+/* Configure DMA                                                              */
+/*----------------------------------------------------------------------------*/
+
+/* USER CODE BEGIN 1 */
+
+/* USER CODE END 1 */
+
+/**
+  * Enable DMA controller clock
+  */
+void MX_DMA_Init(void)
+{
+
+  /* DMA controller clock enable */
+  __HAL_RCC_DMA2_CLK_ENABLE();
+  __HAL_RCC_DMA1_CLK_ENABLE();
+
+  /* DMA interrupt init */
+  /* DMA1_Channel3_IRQn interrupt configuration */
+  HAL_NVIC_SetPriority(DMA1_Channel3_IRQn, 0, 0);
+  HAL_NVIC_EnableIRQ(DMA1_Channel3_IRQn);
+  /* DMA2_Channel4_5_IRQn interrupt configuration */
+  HAL_NVIC_SetPriority(DMA2_Channel4_5_IRQn, 0, 0);
+  HAL_NVIC_EnableIRQ(DMA2_Channel4_5_IRQn);
+
+}
+
+/* USER CODE BEGIN 2 */
+
+/* USER CODE END 2 */
+

Core/Src/gpio.c

@@ -0,0 +1,75 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    gpio.c
+  * @brief   This file provides code for the configuration
+  *          of all used GPIO pins.
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Includes ------------------------------------------------------------------*/
+#include "gpio.h"
+
+/* USER CODE BEGIN 0 */
+
+/* USER CODE END 0 */
+
+/*----------------------------------------------------------------------------*/
+/* Configure GPIO                                                             */
+/*----------------------------------------------------------------------------*/
+/* USER CODE BEGIN 1 */
+
+/* USER CODE END 1 */
+
+/** Configure pins
+     PA8   ------> RCC_MCO
+*/
+void MX_GPIO_Init(void)
+{
+
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+
+  /* GPIO Ports Clock Enable */
+  __HAL_RCC_GPIOB_CLK_ENABLE();
+  __HAL_RCC_GPIOC_CLK_ENABLE();
+  __HAL_RCC_GPIOA_CLK_ENABLE();
+  __HAL_RCC_GPIOD_CLK_ENABLE();
+
+  /*Configure GPIO pin Output Level */
+  HAL_GPIO_WritePin(GPIOB, GPIO_PIN_12|GPIO_PIN_13|GPIO_PIN_14|GPIO_PIN_15, GPIO_PIN_RESET);
+
+  /*Configure GPIO pins : PB12 PB13 PB14 PB15 */
+  GPIO_InitStruct.Pin = GPIO_PIN_12|GPIO_PIN_13|GPIO_PIN_14|GPIO_PIN_15;
+  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+  HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+  /*Configure GPIO pin : PA8 */
+  GPIO_InitStruct.Pin = GPIO_PIN_8;
+  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+  /*Configure GPIO pin : PB5 */
+  GPIO_InitStruct.Pin = GPIO_PIN_5;
+  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+}
+
+/* USER CODE BEGIN 2 */
+
+/* USER CODE END 2 */

Core/Src/main.c

@@ -0,0 +1,233 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file           : main.c
+  * @brief          : Main program body
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+#include "fatfs.h"
+#include "rtc.h"
+
+/* Private includes ----------------------------------------------------------*/
+/* USER CODE BEGIN Includes */
+#include "custom_flash.h"
+#include "gpio.h"
+//#include "bootloader.h"
+/* USER CODE END Includes */
+
+/* Private typedef -----------------------------------------------------------*/
+/* USER CODE BEGIN PTD */
+int friman=0;
+/* USER CODE END PTD */
+
+/* Private define ------------------------------------------------------------*/
+/* USER CODE BEGIN PD */
+
+/* USER CODE END PD */
+
+/* Private macro -------------------------------------------------------------*/
+/* USER CODE BEGIN PM */
+
+/* USER CODE END PM */
+
+/* Private variables ---------------------------------------------------------*/
+
+/* USER CODE BEGIN PV */
+
+/* USER CODE END PV */
+
+/* Private function prototypes -----------------------------------------------*/
+//void SystemClock_Config(void);
+/* USER CODE BEGIN PFP */
+
+/* USER CODE END PFP */
+
+/* Private user code ---------------------------------------------------------*/
+/* USER CODE BEGIN 0 */
+//uint32_t programBytes2Read;
+//uint32_t programBytesCounter;
+//uint32_t currentAddress;
+//UINT readBytes;
+//FRESULT result;
+//extern uint8_t ReceiveDataUART[4];
+//extern uint8_t Data2Write[PAGE_SIZE*2];
+//extern struct flag FLAGS;
+
+//uint8_t *FLASH_Read(uint32_t add)
+//{
+//	return (uint8_t *)add;
+//}
+/* USER CODE END 0 */
+
+/**
+  * @brief  The application entry point.
+  * @retval int
+  */
+int main(void)
+{
+  /* USER CODE BEGIN 1 */
+	SystemClock_Config();
+	//Bootloader_main();
+	REQUESTER_Init();
+	REQUESTER_MainWhile();
+  /* USER CODE END 1 */
+
+  /* MCU Configuration--------------------------------------------------------*/
+
+  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
+  HAL_Init();
+
+  /* USER CODE BEGIN Init */
+
+  /* USER CODE END Init */
+
+  /* USER CODE BEGIN SysInit */
+
+  /* USER CODE END SysInit */
+
+  /* Initialize all configured peripherals */
+  MX_RTC_Init();
+  /* USER CODE BEGIN 2 */
+	
+//	MX_USER_UART_Init();
+//	HAL_UART_Receive_IT(&huart_boot, ReceiveDataUART, sizeof(ReceiveDataUART));
+  /* USER CODE END 2 */
+
+  /* Infinite loop */
+  /* USER CODE BEGIN WHILE */
+  while (1)
+  {
+/*		if (friman)
+		{
+			 
+       SetKey();
+			 HAL_NVIC_SystemReset();
+    }*/
+//		if (FLAGS.reInitMCU == 1)
+//		{
+//			HAL_UART_Receive_DMA(&huart_boot, Data2Write, PAGE_SIZE*2);
+//		}
+//		
+    /* USER CODE END WHILE */
+
+    /* USER CODE BEGIN 3 */
+  }
+  /* USER CODE END 3 */
+}
+
+/**
+  * @brief System Clock Configuration
+  * @retval None
+  */
+void SystemClock_Config(void)
+{
+  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
+  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
+  RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};
+
+  /** Initializes the RCC Oscillators according to the specified parameters
+  * in the RCC_OscInitTypeDef structure.
+  */
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI|RCC_OSCILLATORTYPE_LSI;
+  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
+  RCC_OscInitStruct.LSIState = RCC_LSI_ON;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI_DIV2;
+  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL16;
+  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
+  {
+    Error_Handler();
+  }
+
+  /** Initializes the CPU, AHB and APB buses clocks
+  */
+  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
+                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+
+  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_RTC;
+  PeriphClkInit.RTCClockSelection = RCC_RTCCLKSOURCE_LSI;
+  if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  HAL_RCC_MCOConfig(RCC_MCO, RCC_MCO1SOURCE_PLLCLK, RCC_MCODIV_1);
+}
+
+/* USER CODE BEGIN 4 */
+
+/* USER CODE END 4 */
+
+/**
+  * @brief  Period elapsed callback in non blocking mode
+  * @note   This function is called  when TIM8 interrupt took place, inside
+  * HAL_TIM_IRQHandler(). It makes a direct call to HAL_IncTick() to increment
+  * a global variable "uwTick" used as application time base.
+  * @param  htim : TIM handle
+  * @retval None
+  */
+void HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef *htim)
+{
+  /* USER CODE BEGIN Callback 0 */
+
+  /* USER CODE END Callback 0 */
+  if (htim->Instance == TIM8) {
+    HAL_IncTick();
+  }
+  /* USER CODE BEGIN Callback 1 */
+
+  /* USER CODE END Callback 1 */
+}
+
+/**
+  * @brief  This function is executed in case of error occurrence.
+  * @retval None
+  */
+void Error_Handler(void)
+{
+  /* USER CODE BEGIN Error_Handler_Debug */
+  /* User can add his own implementation to report the HAL error return state */
+  __disable_irq();
+  while (1)
+  {
+  }
+  /* USER CODE END Error_Handler_Debug */
+}
+
+#ifdef  USE_FULL_ASSERT
+/**
+  * @brief  Reports the name of the source file and the source line number
+  *         where the assert_param error has occurred.
+  * @param  file: pointer to the source file name
+  * @param  line: assert_param error line source number
+  * @retval None
+  */
+void assert_failed(uint8_t *file, uint32_t line)
+{
+  /* USER CODE BEGIN 6 */
+  /* User can add his own implementation to report the file name and line number,
+     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
+  /* USER CODE END 6 */
+}
+#endif /* USE_FULL_ASSERT */

Core/Src/requester.c

@@ -0,0 +1,619 @@
+#include "requester.h"
+
+static union Byte byte[2048][8];
+#define byte_modbusadr(x) byte[x/64][(x%64)/8]
+#define _GET_MODBUS_BIT(x) byte[x/64][(x%64)/8].AllBit>>((x%64)%8)
+#define _GET_MODBUS_ADR(SensorId, RequestedBytePosition, RequestedBitPosition) SensorId*64 + RequestedBytePosition*8 + RequestedBitPosition
+
+uint16_t ModbusFilters[COUNT_OF_MODBUS_SECTIONS][2];
+
+struct device CurrentDevice;
+struct device Device_on_the_Network[32];
+struct data Data;
+struct controlflags ControlFlags;
+struct received_request ReceivedRequest;
+
+#define MAX_NUM_OF_DEVICES_PER_LINE 4
+#define MAX_NUM_OF_REGISTERS_IN_DEVICE 255
+
+//Регистр это слово (16 бит). uint16
+uint16_t ModbusDemonstration[MAX_NUM_OF_DEVICES_PER_LINE][MAX_NUM_OF_REGISTERS_IN_DEVICE];
+uint16_t ModbusAlternativeTable[MAX_NUM_OF_DEVICES_PER_LINE*MAX_NUM_OF_REGISTERS_IN_DEVICE];
+
+_Bool IsLeapYear(uint8_t year)
+{
+	year+=2000;
+	return (year%400==0)||((year%4==0)&&(year%100!=0));
+}
+
+/**
+	* @brief Инициализация переферии
+* @details Инициализация HAL, CAN, TIM7, RTC. 
+* @note Фильтры CAN описаны в разделе REQUESTER_CAN_FILTERS().
+*/
+void REQUESTER_Init(void)
+{
+	HAL_Init();	
+	MX_CAN_Init();
+	HAL_CAN_Start(&hcan);
+	REQUESTER_CAN_FILTERS();
+	HAL_CAN_ActivateNotification(&hcan, CAN_IT_RX_FIFO0_MSG_PENDING);
+	ControlFlags.IsPulse = 1;
+	MX_TIM7_Init();
+	MX_RTC_Init();
+	
+	#ifdef _DEMO
+	int Reg_AltModbusTable;
+	//Тестовые значения регистров. Для отладки/демонстрации
+	for(int x = 0; x < MAX_NUM_OF_DEVICES_PER_LINE; x++)
+	{
+		for(int y = 0; y < MAX_NUM_OF_REGISTERS_IN_DEVICE; y++)
+		{
+			ModbusDemonstration[x][y] = x<<8 | y;
+			
+			Reg_AltModbusTable = x*MAX_NUM_OF_REGISTERS_IN_DEVICE+y;
+			
+			ModbusAlternativeTable[Reg_AltModbusTable] = x<<8 | y;
+		}
+	}
+	#endif
+}
+
+int ProverkaDefinaResult;
+int ProverkaDefinaItem = 0;
+int ProverkaArbitors = 0;
+
+/**
+* @brief Функция с обработкой полученных запросов
+* @details В бесконечном цикле функция ожидает выставление флага о полученном запросе.
+* Обработка запроса аналоговых значений - REQUESTER_AnalogProcessing().
+*	Обработка широковещательных запросов - REQUESTER_BroadcastProcessing().
+* Обработка запроса дискретных значений - REQUESTER_DiscreticProcessing().
+* Обработка Modbus - REQUESTER_ModbusProcessing().
+* @note
+*/
+void REQUESTER_MainWhile(void)
+{
+	CAN_TxHeaderTypeDef TxHeader;
+	uint32_t TxMailBox = 0;
+	uint8_t data[8];
+	union ext_ID eID;
+	eID.Fields.DeviceID = 16;
+	eID.Fields.DataType = DATA_TYPE_ANALOG;
+	eID.Fields.SensorType = 0x1F;
+	eID.Fields.SensorID = 0;
+	eID.Fields.Route = ROUTE_SLAVE;
+	TxHeader.TransmitGlobalTime = DISABLE;
+	TxHeader.RTR = CAN_RTR_DATA;
+	int TxTest = 0;
+	HAL_TIM_Base_Start_IT(&htim7);
+	while(1)
+	{
+		if(ReceivedRequest.AnalogFlags.AllFlags)
+		{
+			REQUESTER_AnalogProcessing();
+		}
+		if(ReceivedRequest.BroadcastFlags.AllFlags)
+		{
+			REQUESTER_BroadcastProcessing();
+		}
+		if(ReceivedRequest.DiscreticFlags.AllFlags)
+		{
+			REQUESTER_DiscreticProcessing();
+		}
+		if(ReceivedRequest.ModbusFlags.AllFlags)
+		{
+			REQUESTER_ModbusProcessing();
+		}		
+		while(HAL_CAN_GetTxMailboxesFreeLevel(&hcan) == 0);
+		TxHeader.ExtId = eID.BitAll;
+		if(HAL_CAN_AddTxMessage(&hcan, &TxHeader, data, &TxMailBox)!= HAL_OK)
+		{
+			ProverkaArbitors++;
+		}
+		eID.Fields.SensorID++;
+		if(eID.Fields.SensorID>100)
+		{
+			eID.Fields.SensorID = 0;
+		}			
+	}
+}
+
+/**
+* @brief Функция обработки аналоговых запросов.
+* @details Функция, формирующая и отправляющая ответ на запросы. Типы запросов: Универсальный, Уставки, Напряжение, Ток, Температура
+*/
+void REQUESTER_AnalogProcessing()
+{
+	CAN_TxHeaderTypeDef TxHeader;
+	uint32_t TxMailBox = 0;
+	uint8_t data[8];
+	if(ReceivedRequest.AnalogFlags.AnalogType.Request_Universal_Sens)
+	{
+		ReceivedRequest.AnalogFlags.AnalogType.Request_Universal_Sens = 0;
+	}
+	if(ReceivedRequest.AnalogFlags.AnalogType.Request_U_Sens)
+	{
+		//Запрос на данные датчика напряжения.
+		//В дальнейшем реализовать отправку настоящих данных.
+		//А пока - тестовое сообщение, нужное для отладки.
+		//Расширенный ID
+		TxHeader.IDE=CAN_ID_EXT;
+		//Ответ на запрос осуществляется по тому-же ID,
+		//с которым был отправлен запрос.
+		union ext_ID eID;
+		eID.BitAll = ReceivedRequest.RequestedExtID.BitAll;
+		eID.Fields.Route = ROUTE_SLAVE;
+		TxHeader.ExtId = eID.BitAll;
+		//Выставляется количество передаваемых байтов. (Макс. 8) 
+		TxHeader.DLC = 6;
+		data[0] = 'U';
+		data[1] = ' ';
+		data[2] = 's';
+		data[3] = 'e';
+		data[4] = 'n';
+		data[5] = 's';
+		HAL_CAN_AddTxMessage(&hcan, &TxHeader, data, &TxMailBox);
+		ReceivedRequest.AnalogFlags.AnalogType.Request_U_Sens=0;
+	}
+	if(ReceivedRequest.AnalogFlags.AnalogType.Request_I_Sens)
+	{
+		TxHeader.IDE=CAN_ID_EXT;
+		union ext_ID eID;
+		eID.BitAll = ReceivedRequest.RequestedExtID.BitAll;
+		eID.Fields.Route = ROUTE_SLAVE;
+		TxHeader.ExtId = eID.BitAll;
+		TxHeader.DLC = 6;
+		data[0] = 'I';
+		data[1] = ' ';
+		data[2] = 's';
+		data[3] = 'e';
+		data[4] = 'n';
+		data[5] = 's';
+		HAL_CAN_AddTxMessage(&hcan, &TxHeader, data, &TxMailBox);
+		ReceivedRequest.AnalogFlags.AnalogType.Request_I_Sens=0;
+	}
+	if(ReceivedRequest.AnalogFlags.AnalogType.Request_T_Sens)
+	{
+		TxHeader.IDE=CAN_ID_EXT;
+		union ext_ID eID;
+		eID.BitAll = ReceivedRequest.RequestedExtID.BitAll;
+		eID.Fields.Route = ROUTE_SLAVE;
+		TxHeader.ExtId = eID.BitAll;
+		TxHeader.DLC = 6;
+		data[0] = 'T';
+		data[1] = ' ';
+		data[2] = 's';
+		data[3] = 'e';
+		data[4] = 'n';
+		data[5] = 's';
+		HAL_CAN_AddTxMessage(&hcan, &TxHeader, data, &TxMailBox);
+		ReceivedRequest.AnalogFlags.AnalogType.Request_T_Sens=0;
+	}
+}
+
+/**
+* @brief Функция обработки широковещательных запросов.
+* @details Функция, выполняющая команды, переданные в широковещательном формате с головного (master) устройства. Типы команд: Запрос статуса, запрос на включение или выключение, рестарт устройств, установка времени.
+*/
+void REQUESTER_BroadcastProcessing()
+{
+	if(ReceivedRequest.BroadcastFlags.BroadcastType.Request_OnOff)
+	{
+		//Обработка запроса на вкл/выкл 
+		ControlFlags.IsPulse = !ControlFlags.IsPulse;
+		ReceivedRequest.BroadcastFlags.BroadcastType.Request_OnOff = 0;
+	}
+	if(ReceivedRequest.BroadcastFlags.BroadcastType.Request_RTC_Setup)
+	{
+		//Обработка запроса на синхронизацию времени
+		//С головным устройством
+		if(ReceivedRequest.RequestedDLC > 7)
+		{
+			//ERROR
+		}
+		else
+		{
+			int DaysCount_Normal[2][12] = {{31, 28, 31, 30, 31, 30, 31, 31, 30, 31, 30, 31}, 
+																			{31, 29, 31, 30, 31, 30, 31, 31, 30, 31, 30, 31}};
+			if (ReceivedRequest.RxData[0]>23 ||
+					ReceivedRequest.RxData[1]>59 ||
+					ReceivedRequest.RxData[2]>59 ||
+					ReceivedRequest.RxData[3]>99 ||
+					ReceivedRequest.RxData[4]>12 ||
+					ReceivedRequest.RxData[5] > DaysCount_Normal[IsLeapYear(ReceivedRequest.RxData[3])][ReceivedRequest.RxData[4]] ||
+					ReceivedRequest.RxData[6]>6)
+			{
+				//ERROR
+			}
+			else
+			{
+				REQUESTER_RTC_SYNC(ReceivedRequest.RxData);
+			}
+		}
+		ReceivedRequest.BroadcastFlags.BroadcastType.Request_RTC_Setup = 0;
+	}
+	if(ReceivedRequest.BroadcastFlags.BroadcastType.Request_Status)
+	{
+		//Обработка запроса статуса устройства
+		RTC_TimeTypeDef sTime = {0};
+		RTC_DateTypeDef DateToUpdate = {0};
+		HAL_RTC_GetTime(&hrtc, &sTime, RTC_FORMAT_BIN);
+		CAN_TxHeaderTypeDef TxHeader;
+		uint32_t TxMailBox = 0;
+		uint8_t data[8];	
+		TxHeader.IDE=CAN_ID_EXT;
+		union ext_ID eID;
+		eID.BitAll = ReceivedRequest.RequestedExtID.BitAll;
+		eID.Fields.Route = ROUTE_SLAVE;
+		TxHeader.ExtId = eID.BitAll;
+		TxHeader.DLC = 7;
+		data[0] = sTime.Hours;
+		data[1] = sTime.Minutes;
+		data[2] = sTime.Seconds;
+		HAL_RTC_GetDate(&hrtc, &DateToUpdate, RTC_FORMAT_BIN);
+		
+		data[3] = DateToUpdate.Year;
+		data[4] = DateToUpdate.Month;
+		data[5] = DateToUpdate.Date;
+		data[6] = DateToUpdate.WeekDay;
+		
+		HAL_CAN_AddTxMessage(&hcan, &TxHeader, data, &TxMailBox);
+		ReceivedRequest.AnalogFlags.AnalogType.Request_T_Sens=0;
+		ReceivedRequest.BroadcastFlags.BroadcastType.Request_Status = 0;
+	}
+}
+
+/**
+* @brief Функция обработки дискретных запросов.
+* @details Функция, формирующая и отправляющая ответ на запросы. Типы запросов: Аварии, Предупреждения, Управляющие сигналы, Флаги, Рестарт устройства, Изменение режима работы устройства, Запрос на устройство.
+* @note Запрос на устройство. Головное (master) устройство запрашивает некоторое колличество параметров. В Data - 64 битовых адресса параметров, тип которых задаётся в Sensor ID. Имеется возможность запрашивать непоследовательные параметры.
+*/
+void REQUESTER_DiscreticProcessing()
+{
+	if(ReceivedRequest.DiscreticFlags.DiscreticType.Request_Accident)
+	{
+		ReceivedRequest.DiscreticFlags.DiscreticType.Request_Accident = 0;
+	}
+	if(ReceivedRequest.DiscreticFlags.DiscreticType.Request_Control_Signals)
+	{
+		ReceivedRequest.DiscreticFlags.DiscreticType.Request_Control_Signals = 0;
+	}
+	if(ReceivedRequest.DiscreticFlags.DiscreticType.Request_Flags)
+	{
+		ReceivedRequest.DiscreticFlags.DiscreticType.Request_Flags = 0;
+	}
+	if(ReceivedRequest.DiscreticFlags.DiscreticType.Request_Warning)
+	{
+		ReceivedRequest.DiscreticFlags.DiscreticType.Request_Warning = 0;
+	}
+	if(ReceivedRequest.DiscreticFlags.DiscreticType.Request_Reset)
+	{
+		ReceivedRequest.DiscreticFlags.DiscreticType.Request_Reset = 0;
+		NVIC_SystemReset();
+	}
+	if(ReceivedRequest.DiscreticFlags.DiscreticType.Request_List_of_Parameters)
+	{
+		ReceivedRequest.DiscreticFlags.DiscreticType.Request_List_of_Parameters = 0;
+		for(int Current_byte = 0; Current_byte < 8; Current_byte++)
+		{
+			for(int Current_bit = 0; Current_bit < 8; Current_bit++)
+			{
+				if((ReceivedRequest.RxData[Current_byte]>>Current_bit)&0b1)
+				{
+					_GET_MODBUS_ADR(ReceivedRequest.RequestedExtID.Fields.SensorID, Current_byte, Current_bit);
+				}
+			}
+		}
+	}
+}
+
+/**
+* @brief Функция обработки Modbus запросов.
+* @details Функция, формирующая и отправляющая ответ на запросы.
+*/
+void REQUESTER_ModbusProcessing()
+{
+	if((ReceivedRequest.SensorToModbus.Modbus.StrAdr>=0) && (ReceivedRequest.SensorToModbus.Modbus.StrAdr<=127))
+	{
+		//Обращение к существующему в устройстве модбас регистру
+		CAN_TxHeaderTypeDef TxHeader;
+		uint32_t TxMailBox = 0;
+		uint8_t data[8];
+		TxHeader.IDE = CAN_ID_EXT;
+		TxHeader.DLC = 8;
+		TxHeader.RTR = CAN_RTR_DATA;
+		
+		int RequestFromDLC;
+		for(RequestFromDLC = ReceivedRequest.SensorToModbus.Modbus.StrAdr; 
+			(RequestFromDLC<MAX_NUM_OF_REGISTERS_IN_DEVICE) && 
+			((RequestFromDLC-ReceivedRequest.SensorToModbus.Modbus.StrAdr)<ReceivedRequest.SensorToModbus.Modbus.Count); 
+//				RequestFromDLC++
+			)
+		{
+			TxHeader.DLC = 0;
+			union ext_ID eID;
+			eID.BitAll = ReceivedRequest.RequestedExtID.BitAll;
+			eID.Fields.Route = ROUTE_SLAVE;
+			eID.Fields.SensorType = RequestFromDLC>>11;
+			eID.Fields.SensorID = RequestFromDLC;
+			TxHeader.ExtId = eID.BitAll;
+			for(int DataFor = 0; DataFor < 8; DataFor+=2)
+			{
+				data[DataFor] = HighByteOfWord(ModbusDemonstration[CURRENT_ID_DEVICE][RequestFromDLC]);
+				data[DataFor+1] = LowByteOfWord(ModbusDemonstration[CURRENT_ID_DEVICE][RequestFromDLC]);
+				RequestFromDLC++;
+				TxHeader.DLC +=2;
+				if(!((RequestFromDLC<MAX_NUM_OF_REGISTERS_IN_DEVICE) && 
+					((RequestFromDLC-ReceivedRequest.SensorToModbus.Modbus.StrAdr)<ReceivedRequest.SensorToModbus.Modbus.Count)))
+				{
+					break;
+				}
+			}
+			while(HAL_CAN_GetTxMailboxesFreeLevel(&hcan) == 0);
+			HAL_CAN_AddTxMessage(&hcan, &TxHeader, data, &TxMailBox);
+		}
+		union ext_ID_Modbus extID;
+		extID.Fields.DeviceID = CURRENT_ID_DEVICE;
+		extID.Fields.DataType = DATA_TYPE_ERROR;
+		extID.Fields.CountReg = NONEXISTENT_ELEMENT;
+		extID.Fields.Route = ROUTE_SLAVE;
+		TxHeader.DLC = 0;
+		for(;(RequestFromDLC-ReceivedRequest.SensorToModbus.Modbus.StrAdr)<ReceivedRequest.SensorToModbus.Modbus.Count; RequestFromDLC++)
+		{
+			extID.Fields.StrAdr = RequestFromDLC;
+			TxHeader.ExtId = extID.BitAll;
+			while(HAL_CAN_GetTxMailboxesFreeLevel(&hcan) == 0);
+			HAL_CAN_AddTxMessage(&hcan, &TxHeader, data, &TxMailBox);
+		}
+		ReceivedRequest.ModbusFlags.AllFlags = 0;
+		return;
+	}
+	ReceivedRequest.ModbusFlags.AllFlags = 0;
+}
+
+void HAL_CAN_RxFifo0MsgPendingCallback(CAN_HandleTypeDef *hcan)
+{
+	CAN_RxHeaderTypeDef RxHeader;
+	uint8_t RCAN_Data[8];
+	HAL_CAN_GetRxMessage(hcan, CAN_RX_FIFO0, &RxHeader, RCAN_Data);
+	//Расширенный ID
+	if(RxHeader.IDE == CAN_ID_EXT)
+	{
+		union ext_ID ExtID_Of_RX_MSG;
+		ExtID_Of_RX_MSG.BitAll = RxHeader.ExtId;
+		//Полученное сообщение - широковещательное
+		if (ExtID_Of_RX_MSG.Fields.DeviceID == ID_MAIN_DEVICE)
+		{
+			if(ExtID_Of_RX_MSG.Fields.DataType == DATA_TYPE_BROADCAST)
+			{
+				switch(ExtID_Of_RX_MSG.Fields.SensorType)
+				{
+					case SENSOR_TYPE_STATUS:
+						ReceivedRequest.BroadcastFlags.BroadcastType.Request_Status = 1;
+						break;
+					case SENSOR_TYPE_ONOFF:
+						ReceivedRequest.BroadcastFlags.BroadcastType.Request_OnOff = 1;
+						break;
+					case SENSOR_TYPE_RTCSETUP:
+						ReceivedRequest.RequestedDLC = RxHeader.DLC;
+						ReceivedRequest.RxData[0] = RCAN_Data[0];
+						ReceivedRequest.RxData[1] = RCAN_Data[1];
+						ReceivedRequest.RxData[2] = RCAN_Data[2];
+						ReceivedRequest.RxData[3] = RCAN_Data[3];
+						ReceivedRequest.RxData[4] = RCAN_Data[4];
+						ReceivedRequest.RxData[5] = RCAN_Data[5];
+						ReceivedRequest.RxData[6] = RCAN_Data[6];
+						ReceivedRequest.BroadcastFlags.BroadcastType.Request_RTC_Setup = 1;
+						break;
+					default:
+						break;
+				}
+				return;
+			}
+		}
+		//Если ID запроса соответствует ID устройства
+		if(ExtID_Of_RX_MSG.Fields.DeviceID == (CURRENT_ID_DEVICE))
+		{
+			if(ExtID_Of_RX_MSG.Fields.DataType == DATA_TYPE_DISCRETE)
+			{
+				switch(ExtID_Of_RX_MSG.Fields.SensorType)
+				{
+					case SENSOR_TYPE_ACCIDENT:
+						break;
+					case SENSOR_TYPE_WARNING:
+						break;
+					case SENSOR_TYPE_CONTROL_SIGNALS:
+						break;
+					case SENSOR_TYPE_FLAGS:
+						break;
+					case SENSOR_TYPE_RESET:
+						ReceivedRequest.DiscreticFlags.DiscreticType.Request_Reset = 1;
+						break;
+					case SENSOR_TYPE_CHANGE_MODE:
+						ControlFlags.IsRtrMode = !ControlFlags.IsRtrMode;
+						break;
+					case SENSOR_TYPE_REQUEST_LIST_OF_PARAMETERS:
+						ReceivedRequest.DiscreticFlags.DiscreticType.Request_List_of_Parameters = 1;
+						break;
+				}
+			}
+			if(ExtID_Of_RX_MSG.Fields.DataType == DATA_TYPE_ANALOG)
+			{
+				//Является ли полученное сообщение - запросом
+				if(RxHeader.RTR)
+				{
+					ReceivedRequest.RequestedExtID.BitAll = ExtID_Of_RX_MSG.BitAll;
+					ReceivedRequest.RequestedDLC = RxHeader.DLC;
+					//Определяется запрашиваемая информация
+					switch(ExtID_Of_RX_MSG.Fields.SensorType)
+					{
+						case SENSOR_TYPE_UNIVERSAL:
+						{
+							ReceivedRequest.AnalogFlags.AnalogType.Request_Universal_Sens=1;
+							break;
+						}
+						case SENSOR_TYPE_U:
+						{
+							ReceivedRequest.AnalogFlags.AnalogType.Request_U_Sens=1;
+							break;
+						}
+						case SENSOR_TYPE_I:
+						{
+							ReceivedRequest.AnalogFlags.AnalogType.Request_I_Sens=1;
+							break;
+						}
+						case SENSOR_TYPE_T:
+						{
+							ReceivedRequest.AnalogFlags.AnalogType.Request_T_Sens=1;
+							break;
+						}
+					}
+				}
+			}
+			if(ExtID_Of_RX_MSG.Fields.DataType == DATA_TYPE_MODBUS_COIL)
+			{
+				ReceivedRequest.RequestedExtID.BitAll = ExtID_Of_RX_MSG.BitAll;
+				ReceivedRequest.SensorToModbus.Sensor = SensorToModbusRegister(ReceivedRequest.RequestedExtID.Fields.SensorType, ReceivedRequest.RequestedExtID.Fields.SensorID);
+				ReceivedRequest.ModbusFlags.ModbusType.Coil = 1;
+			}
+			if(ExtID_Of_RX_MSG.Fields.DataType == DATA_TYPE_MODBUS_DISCRETE)
+			{
+				ReceivedRequest.RequestedExtID.BitAll = ExtID_Of_RX_MSG.BitAll;
+				ReceivedRequest.SensorToModbus.Sensor = SensorToModbusRegister(ReceivedRequest.RequestedExtID.Fields.SensorType, ReceivedRequest.RequestedExtID.Fields.SensorID);
+				ReceivedRequest.ModbusFlags.ModbusType.Discrete = 1;
+			}
+			if(ExtID_Of_RX_MSG.Fields.DataType == DATA_TYPE_MODBUS_HOLDING)
+			{
+				ReceivedRequest.RequestedExtID.BitAll = ExtID_Of_RX_MSG.BitAll;
+				ReceivedRequest.SensorToModbus.Sensor = SensorToModbusRegister(ReceivedRequest.RequestedExtID.Fields.SensorType, ReceivedRequest.RequestedExtID.Fields.SensorID);
+				ReceivedRequest.ModbusFlags.ModbusType.Holding = 1;
+			}
+			if(ExtID_Of_RX_MSG.Fields.DataType == DATA_TYPE_MODBUS_INPUT)
+			{
+				ReceivedRequest.RequestedExtID.BitAll = ExtID_Of_RX_MSG.BitAll;
+				ReceivedRequest.SensorToModbus.Sensor = SensorToModbusRegister(ReceivedRequest.RequestedExtID.Fields.SensorType, ReceivedRequest.RequestedExtID.Fields.SensorID);
+				ReceivedRequest.ModbusFlags.ModbusType.Input = 1;
+			}
+		}
+		//Полученное сообщение - пульс устройств в сети
+		if (ExtID_Of_RX_MSG.Fields.DataType == DATA_TYPE_PULSE)
+		{
+			Device_on_the_Network[ExtID_Of_RX_MSG.Fields.DeviceID].Status = ONLINE;
+			Device_on_the_Network[ExtID_Of_RX_MSG.Fields.DeviceID].TimeFromLastPulse = 0;
+		}
+	}
+}
+
+void REQUESTER_Pulse_TIM_Handler()
+{
+	if(ControlFlags.IsPulse)
+	{
+		static unsigned PulseStage = 0;
+		CAN_TxHeaderTypeDef TxHeader;
+		uint32_t TxMailBox = 0;
+		union ext_ID currentID;
+		currentID.BitAll = 0;
+		currentID.Fields.DeviceID = CURRENT_ID_DEVICE;
+		currentID.Fields.DataType = DATA_TYPE_PULSE;
+		currentID.Fields.Route = ROUTE_SLAVE;
+		TxHeader.ExtId = currentID.BitAll;
+		uint8_t data[8];
+		TxHeader.IDE = CAN_ID_EXT;
+		TxHeader.TransmitGlobalTime = DISABLE;
+		TxHeader.RTR = CAN_RTR_DATA;
+		TxHeader.DLC = 1;
+		if(PulseStage > 0xFF)
+		{
+			PulseStage = 0;
+		}
+		data[0] = PulseStage++;
+		HAL_CAN_AddTxMessage(&hcan, &TxHeader, data, &TxMailBox);
+	}
+}
+
+void REQUESTER_RTC_SYNC(uint8_t *data)
+{
+	__HAL_RTC_WRITEPROTECTION_DISABLE(&hrtc);
+	RTC_TimeTypeDef sTime = {0};
+  RTC_DateTypeDef DateToUpdate = {0};
+	
+	sTime.Hours = data[0];
+  sTime.Minutes = data[1];
+  sTime.Seconds = data[2];
+	
+  if (HAL_RTC_SetTime(&hrtc, &sTime, RTC_FORMAT_BIN) != HAL_OK)
+  {
+    Error_Handler();
+  }
+
+  DateToUpdate.Year = data[3];
+  DateToUpdate.Month = data[4];
+  DateToUpdate.Date = data[5];
+  DateToUpdate.WeekDay = data[6];
+  if (HAL_RTC_SetDate(&hrtc, &DateToUpdate, RTC_FORMAT_BIN) != HAL_OK)
+  {
+    Error_Handler();
+  }
+	__HAL_RTC_WRITEPROTECTION_ENABLE(&hrtc);
+}
+
+void REQUESTER_CAN_FILTERS()
+{
+	//MAIN DEVICE
+	CAN_FilterTypeDef canFilterConfig;
+	canFilterConfig.FilterBank = 0;
+	canFilterConfig.FilterMode = CAN_FILTERMODE_IDMASK;
+	canFilterConfig.FilterScale = CAN_FILTERSCALE_32BIT;
+	/*Для ID устройства используются восемь младших битов.
+	Макс значение 0 устройство - 0x000, 1 - 0x002, 2 - 0x004, 3 - 0x006*/
+	canFilterConfig.FilterIdHigh = (uint16_t)(ID_MAIN_DEVICE>>13);
+	canFilterConfig.FilterIdLow = (uint16_t)(ID_MAIN_DEVICE<<5) | CAN_IDE_32;
+	/*Маска 1.1111.1110.<...>. Нули - любые символы. Единицы - точное соответствие фильтру выше.*/
+	canFilterConfig.FilterMaskIdHigh = (uint16_t)(CAN_DEVICE_ID_FILTER>>13);
+	canFilterConfig.FilterMaskIdLow = (uint16_t)(CAN_DEVICE_ID_FILTER<<3) | CAN_IDE_32;
+	canFilterConfig.FilterFIFOAssignment = CAN_RX_FIFO0;
+	canFilterConfig.FilterActivation = ENABLE;
+	canFilterConfig.SlaveStartFilterBank = 14;
+	if(HAL_CAN_ConfigFilter(&hcan, &canFilterConfig) != HAL_OK)
+	{
+    Error_Handler();
+	}
+	
+	//CURRENT DEVICE
+	canFilterConfig.FilterBank = 1;
+	/*Для ID устройства используются восемь младших битов.
+	Макс значение 0 устройство - 0x000, 1 - 0x002, 2 - 0x004, 3 - 0x006*/
+	canFilterConfig.FilterIdHigh = (uint16_t)(CURRENT_ID_DEVICE>>13);
+	canFilterConfig.FilterIdLow = (uint16_t)(CURRENT_ID_DEVICE<<5) | CAN_IDE_32;
+	/*Маска 1.1111.1110.<...>. Нули - любые символы. Единицы - точное соответствие фильтру выше.*/
+	canFilterConfig.FilterMaskIdHigh = (uint16_t)(CAN_DEVICE_ID_FILTER>>13);
+	canFilterConfig.FilterMaskIdLow = (uint16_t)(CAN_DEVICE_ID_FILTER<<3) | CAN_IDE_32;
+	if(HAL_CAN_ConfigFilter(&hcan, &canFilterConfig) != HAL_OK)
+	{
+    Error_Handler();
+	}
+	
+	//MODBUS
+	canFilterConfig.FilterBank = 2;
+	canFilterConfig.FilterIdHigh = (uint16_t)(0x03000000>>13);
+	canFilterConfig.FilterIdLow = (uint16_t)(0x03000000<<5) | CAN_IDE_32;
+	canFilterConfig.FilterMaskIdHigh = 	(uint16_t)(CAN_DATA_TYPE_FILTER>>13); // we're checking only high 13 bits, that contained "key"
+	canFilterConfig.FilterMaskIdLow = 	(uint16_t)(CAN_DATA_TYPE_FILTER<<3) | CAN_IDE_32; // 1<<2 - set IDE bit
+	if(HAL_CAN_ConfigFilter(&hcan, &canFilterConfig) != HAL_OK)
+	{
+		Error_Handler();
+	}
+	
+	//PULSE
+	canFilterConfig.FilterBank = 3;
+	canFilterConfig.FilterIdHigh = (uint16_t)(HighIdFilter(DATA_TYPE_PULSE)>>13);
+	//canFilterConfig.FilterIdHigh = (uint16_t)(0x1F000000>>13);
+	canFilterConfig.FilterIdLow = (uint16_t)(HighIdFilter(DATA_TYPE_PULSE)<<5) | CAN_IDE_32;
+	canFilterConfig.FilterMaskIdHigh = 	(uint16_t)(CAN_DATA_TYPE_FILTER>>13); // we're checking only high 13 bits, that contained "key"
+	canFilterConfig.FilterMaskIdLow = 	(uint16_t)(CAN_DATA_TYPE_FILTER<<3) | CAN_IDE_32; // 1<<2 - set IDE bit
+	if(HAL_CAN_ConfigFilter(&hcan, &canFilterConfig) != HAL_OK)
+	{
+		Error_Handler();
+	}
+}

Core/Src/rtc.c

@@ -0,0 +1,121 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    rtc.c
+  * @brief   This file provides code for the configuration
+  *          of the RTC instances.
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+/* Includes ------------------------------------------------------------------*/
+#include "rtc.h"
+
+/* USER CODE BEGIN 0 */
+
+/* USER CODE END 0 */
+
+RTC_HandleTypeDef hrtc;
+
+/* RTC init function */
+void MX_RTC_Init(void)
+{
+
+  /* USER CODE BEGIN RTC_Init 0 */
+
+  /* USER CODE END RTC_Init 0 */
+
+  RTC_TimeTypeDef sTime = {0};
+  RTC_DateTypeDef DateToUpdate = {0};
+
+  /* USER CODE BEGIN RTC_Init 1 */
+
+  /* USER CODE END RTC_Init 1 */
+
+  /** Initialize RTC Only
+  */
+  hrtc.Instance = RTC;
+  hrtc.Init.AsynchPrediv = RTC_AUTO_1_SECOND;
+  hrtc.Init.OutPut = RTC_OUTPUTSOURCE_ALARM;
+  if (HAL_RTC_Init(&hrtc) != HAL_OK)
+  {
+    Error_Handler();
+  }
+
+  /* USER CODE BEGIN Check_RTC_BKUP */
+
+	// Время отсчитывается от 12.03.2024 в секундах (регистры RTC)
+  /* USER CODE END Check_RTC_BKUP */
+
+  /** Initialize RTC and set the Time and Date
+  */
+  sTime.Hours = 0;
+  sTime.Minutes = 0;
+  sTime.Seconds = 0;
+
+  if (HAL_RTC_SetTime(&hrtc, &sTime, RTC_FORMAT_BIN) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  DateToUpdate.WeekDay = RTC_WEEKDAY_MONDAY;
+  DateToUpdate.Month = RTC_MONTH_JANUARY;
+  DateToUpdate.Date = 1;
+  DateToUpdate.Year = 0;
+
+  if (HAL_RTC_SetDate(&hrtc, &DateToUpdate, RTC_FORMAT_BIN) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN RTC_Init 2 */
+
+  /* USER CODE END RTC_Init 2 */
+
+}
+
+void HAL_RTC_MspInit(RTC_HandleTypeDef* rtcHandle)
+{
+
+  if(rtcHandle->Instance==RTC)
+  {
+  /* USER CODE BEGIN RTC_MspInit 0 */
+
+  /* USER CODE END RTC_MspInit 0 */
+    HAL_PWR_EnableBkUpAccess();
+    /* Enable BKP CLK enable for backup registers */
+    __HAL_RCC_BKP_CLK_ENABLE();
+    /* RTC clock enable */
+    __HAL_RCC_RTC_ENABLE();
+  /* USER CODE BEGIN RTC_MspInit 1 */
+
+  /* USER CODE END RTC_MspInit 1 */
+  }
+}
+
+void HAL_RTC_MspDeInit(RTC_HandleTypeDef* rtcHandle)
+{
+
+  if(rtcHandle->Instance==RTC)
+  {
+  /* USER CODE BEGIN RTC_MspDeInit 0 */
+
+  /* USER CODE END RTC_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_RTC_DISABLE();
+  /* USER CODE BEGIN RTC_MspDeInit 1 */
+
+  /* USER CODE END RTC_MspDeInit 1 */
+  }
+}
+
+/* USER CODE BEGIN 1 */
+
+/* USER CODE END 1 */

Core/Src/sdio.c

@@ -0,0 +1,151 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    sdio.c
+  * @brief   This file provides code for the configuration
+  *          of the SDIO instances.
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+/* Includes ------------------------------------------------------------------*/
+#include "sdio.h"
+
+/* USER CODE BEGIN 0 */
+
+/* USER CODE END 0 */
+
+SD_HandleTypeDef hsd;
+DMA_HandleTypeDef hdma_sdio;
+
+/* SDIO init function */
+
+void MX_SDIO_SD_Init(void)
+{
+
+  /* USER CODE BEGIN SDIO_Init 0 */
+
+  /* USER CODE END SDIO_Init 0 */
+
+  /* USER CODE BEGIN SDIO_Init 1 */
+
+  /* USER CODE END SDIO_Init 1 */
+  hsd.Instance = SDIO;
+  hsd.Init.ClockEdge = SDIO_CLOCK_EDGE_RISING;
+  hsd.Init.ClockBypass = SDIO_CLOCK_BYPASS_DISABLE;
+  hsd.Init.ClockPowerSave = SDIO_CLOCK_POWER_SAVE_DISABLE;
+  hsd.Init.BusWide = SDIO_BUS_WIDE_4B;
+  hsd.Init.HardwareFlowControl = SDIO_HARDWARE_FLOW_CONTROL_DISABLE;
+  hsd.Init.ClockDiv = 4;
+  /* USER CODE BEGIN SDIO_Init 2 */
+
+  /* USER CODE END SDIO_Init 2 */
+
+}
+
+void HAL_SD_MspInit(SD_HandleTypeDef* sdHandle)
+{
+
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+  if(sdHandle->Instance==SDIO)
+  {
+  /* USER CODE BEGIN SDIO_MspInit 0 */
+
+  /* USER CODE END SDIO_MspInit 0 */
+    /* SDIO clock enable */
+    __HAL_RCC_SDIO_CLK_ENABLE();
+
+    __HAL_RCC_GPIOC_CLK_ENABLE();
+    __HAL_RCC_GPIOD_CLK_ENABLE();
+    /**SDIO GPIO Configuration
+    PC8     ------> SDIO_D0
+    PC9     ------> SDIO_D1
+    PC10     ------> SDIO_D2
+    PC11     ------> SDIO_D3
+    PC12     ------> SDIO_CK
+    PD2     ------> SDIO_CMD
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_8|GPIO_PIN_9|GPIO_PIN_10|GPIO_PIN_11
+                          |GPIO_PIN_12;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+    HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_2;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+    HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
+
+    /* SDIO DMA Init */
+    /* SDIO Init */
+    hdma_sdio.Instance = DMA2_Channel4;
+    hdma_sdio.Init.Direction = DMA_PERIPH_TO_MEMORY;
+    hdma_sdio.Init.PeriphInc = DMA_PINC_DISABLE;
+    hdma_sdio.Init.MemInc = DMA_MINC_ENABLE;
+    hdma_sdio.Init.PeriphDataAlignment = DMA_PDATAALIGN_WORD;
+    hdma_sdio.Init.MemDataAlignment = DMA_MDATAALIGN_WORD;
+    hdma_sdio.Init.Mode = DMA_NORMAL;
+    hdma_sdio.Init.Priority = DMA_PRIORITY_LOW;
+    if (HAL_DMA_Init(&hdma_sdio) != HAL_OK)
+    {
+      Error_Handler();
+    }
+
+    /* Several peripheral DMA handle pointers point to the same DMA handle.
+     Be aware that there is only one channel to perform all the requested DMAs. */
+    /* Be sure to change transfer direction before calling
+     HAL_SD_ReadBlocks_DMA or HAL_SD_WriteBlocks_DMA. */
+    __HAL_LINKDMA(sdHandle,hdmarx,hdma_sdio);
+    __HAL_LINKDMA(sdHandle,hdmatx,hdma_sdio);
+
+  /* USER CODE BEGIN SDIO_MspInit 1 */
+
+  /* USER CODE END SDIO_MspInit 1 */
+  }
+}
+
+void HAL_SD_MspDeInit(SD_HandleTypeDef* sdHandle)
+{
+
+  if(sdHandle->Instance==SDIO)
+  {
+  /* USER CODE BEGIN SDIO_MspDeInit 0 */
+
+  /* USER CODE END SDIO_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_SDIO_CLK_DISABLE();
+
+    /**SDIO GPIO Configuration
+    PC8     ------> SDIO_D0
+    PC9     ------> SDIO_D1
+    PC10     ------> SDIO_D2
+    PC11     ------> SDIO_D3
+    PC12     ------> SDIO_CK
+    PD2     ------> SDIO_CMD
+    */
+    HAL_GPIO_DeInit(GPIOC, GPIO_PIN_8|GPIO_PIN_9|GPIO_PIN_10|GPIO_PIN_11
+                          |GPIO_PIN_12);
+
+    HAL_GPIO_DeInit(GPIOD, GPIO_PIN_2);
+
+    /* SDIO DMA DeInit */
+    HAL_DMA_DeInit(sdHandle->hdmarx);
+    HAL_DMA_DeInit(sdHandle->hdmatx);
+  /* USER CODE BEGIN SDIO_MspDeInit 1 */
+
+  /* USER CODE END SDIO_MspDeInit 1 */
+  }
+}
+
+/* USER CODE BEGIN 1 */
+
+/* USER CODE END 1 */

Core/Src/stm32f1xx_hal_msp.c

@@ -0,0 +1,81 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file         stm32f1xx_hal_msp.c
+  * @brief        This file provides code for the MSP Initialization
+  *               and de-Initialization codes.
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+/* USER CODE BEGIN Includes */
+
+/* USER CODE END Includes */
+
+/* Private typedef -----------------------------------------------------------*/
+/* USER CODE BEGIN TD */
+
+/* USER CODE END TD */
+
+/* Private define ------------------------------------------------------------*/
+/* USER CODE BEGIN Define */
+
+/* USER CODE END Define */
+
+/* Private macro -------------------------------------------------------------*/
+/* USER CODE BEGIN Macro */
+
+/* USER CODE END Macro */
+
+/* Private variables ---------------------------------------------------------*/
+/* USER CODE BEGIN PV */
+
+/* USER CODE END PV */
+
+/* Private function prototypes -----------------------------------------------*/
+/* USER CODE BEGIN PFP */
+
+/* USER CODE END PFP */
+
+/* External functions --------------------------------------------------------*/
+/* USER CODE BEGIN ExternalFunctions */
+
+/* USER CODE END ExternalFunctions */
+
+/* USER CODE BEGIN 0 */
+
+/* USER CODE END 0 */
+/**
+  * Initializes the Global MSP.
+  */
+void HAL_MspInit(void)
+{
+  /* USER CODE BEGIN MspInit 0 */
+
+  /* USER CODE END MspInit 0 */
+
+  __HAL_RCC_AFIO_CLK_ENABLE();
+  __HAL_RCC_PWR_CLK_ENABLE();
+
+  /* System interrupt init*/
+
+  /* USER CODE BEGIN MspInit 1 */
+
+  /* USER CODE END MspInit 1 */
+}
+
+/* USER CODE BEGIN 1 */
+
+/* USER CODE END 1 */

Core/Src/stm32f1xx_hal_timebase_tim.c

@@ -0,0 +1,129 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_timebase_TIM.c
+  * @brief   HAL time base based on the hardware TIM.
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal.h"
+#include "stm32f1xx_hal_tim.h"
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+TIM_HandleTypeDef        htim8;
+/* Private function prototypes -----------------------------------------------*/
+void TIM8_IRQHandler(void);
+/* Private functions ---------------------------------------------------------*/
+
+/**
+  * @brief  This function configures the TIM8 as a time base source.
+  *         The time source is configured  to have 1ms time base with a dedicated
+  *         Tick interrupt priority.
+  * @note   This function is called  automatically at the beginning of program after
+  *         reset by HAL_Init() or at any time when clock is configured, by HAL_RCC_ClockConfig().
+  * @param  TickPriority: Tick interrupt priority.
+  * @retval HAL status
+  */
+HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority)
+{
+  RCC_ClkInitTypeDef    clkconfig;
+  uint32_t              uwTimclock = 0U;
+
+  uint32_t              uwPrescalerValue = 0U;
+  uint32_t              pFLatency;
+  HAL_StatusTypeDef     status = HAL_OK;
+
+  /* Enable TIM8 clock */
+  __HAL_RCC_TIM8_CLK_ENABLE();
+
+  /* Get clock configuration */
+  HAL_RCC_GetClockConfig(&clkconfig, &pFLatency);
+
+  /* Compute TIM8 clock */
+      uwTimclock = HAL_RCC_GetPCLK2Freq();
+
+  /* Compute the prescaler value to have TIM8 counter clock equal to 1MHz */
+  uwPrescalerValue = (uint32_t) ((uwTimclock / 1000000U) - 1U);
+
+  /* Initialize TIM8 */
+  htim8.Instance = TIM8;
+
+  /* Initialize TIMx peripheral as follow:
+
+  + Period = [(TIM8CLK/1000) - 1]. to have a (1/1000) s time base.
+  + Prescaler = (uwTimclock/1000000 - 1) to have a 1MHz counter clock.
+  + ClockDivision = 0
+  + Counter direction = Up
+  */
+  htim8.Init.Period = (1000000U / 1000U) - 1U;
+  htim8.Init.Prescaler = uwPrescalerValue;
+  htim8.Init.ClockDivision = 0;
+  htim8.Init.CounterMode = TIM_COUNTERMODE_UP;
+  htim8.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;
+
+  status = HAL_TIM_Base_Init(&htim8);
+  if (status == HAL_OK)
+  {
+    /* Start the TIM time Base generation in interrupt mode */
+    status = HAL_TIM_Base_Start_IT(&htim8);
+    if (status == HAL_OK)
+    {
+    /* Enable the TIM8 global Interrupt */
+        HAL_NVIC_EnableIRQ(TIM8_UP_TIM13_IRQn);
+      /* Configure the SysTick IRQ priority */
+      if (TickPriority < (1UL << __NVIC_PRIO_BITS))
+      {
+        /* Configure the TIM IRQ priority */
+        HAL_NVIC_SetPriority(TIM8_UP_TIM13_IRQn, TickPriority, 0U);
+        uwTickPrio = TickPriority;
+      }
+      else
+      {
+        status = HAL_ERROR;
+      }
+    }
+  }
+
+ /* Return function status */
+  return status;
+}
+
+/**
+  * @brief  Suspend Tick increment.
+  * @note   Disable the tick increment by disabling TIM8 update interrupt.
+  * @param  None
+  * @retval None
+  */
+void HAL_SuspendTick(void)
+{
+  /* Disable TIM8 update Interrupt */
+  __HAL_TIM_DISABLE_IT(&htim8, TIM_IT_UPDATE);
+}
+
+/**
+  * @brief  Resume Tick increment.
+  * @note   Enable the tick increment by Enabling TIM8 update interrupt.
+  * @param  None
+  * @retval None
+  */
+void HAL_ResumeTick(void)
+{
+  /* Enable TIM8 Update interrupt */
+  __HAL_TIM_ENABLE_IT(&htim8, TIM_IT_UPDATE);
+}
+

Core/Src/stm32f1xx_it.c

@@ -0,0 +1,336 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_it.c
+  * @brief   Interrupt Service Routines.
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+#include "stm32f1xx_it.h"
+/* Private includes ----------------------------------------------------------*/
+/* USER CODE BEGIN Includes */
+#include "custom_flash.h"
+#include "requester.h"
+/* USER CODE END Includes */
+
+/* Private typedef -----------------------------------------------------------*/
+/* USER CODE BEGIN TD */
+
+/* USER CODE END TD */
+
+/* Private define ------------------------------------------------------------*/
+/* USER CODE BEGIN PD */
+
+/* USER CODE END PD */
+
+/* Private macro -------------------------------------------------------------*/
+/* USER CODE BEGIN PM */
+
+/* USER CODE END PM */
+
+/* Private variables ---------------------------------------------------------*/
+/* USER CODE BEGIN PV */
+
+/* USER CODE END PV */
+
+/* Private function prototypes -----------------------------------------------*/
+/* USER CODE BEGIN PFP */
+
+/* USER CODE END PFP */
+
+/* Private user code ---------------------------------------------------------*/
+/* USER CODE BEGIN 0 */
+
+/* USER CODE END 0 */
+
+/* External variables --------------------------------------------------------*/
+extern CAN_HandleTypeDef hcan;
+extern DMA_HandleTypeDef hdma_sdio;
+extern TIM_HandleTypeDef htim7;
+extern DMA_HandleTypeDef hdma_usart3_rx;
+extern UART_HandleTypeDef huart3;
+extern TIM_HandleTypeDef htim8;
+
+/* USER CODE BEGIN EV */
+extern uint8_t Data2Write[PAGE_SIZE*2];
+extern uint8_t ReceiveDataUART[4];
+extern struct flag FLAGS;
+extern int cnt_tim_reset;
+/* USER CODE END EV */
+
+/******************************************************************************/
+/*           Cortex-M3 Processor Interruption and Exception Handlers          */
+/******************************************************************************/
+/**
+  * @brief This function handles Non maskable interrupt.
+  */
+void NMI_Handler(void)
+{
+  /* USER CODE BEGIN NonMaskableInt_IRQn 0 */
+
+  /* USER CODE END NonMaskableInt_IRQn 0 */
+  /* USER CODE BEGIN NonMaskableInt_IRQn 1 */
+  while (1)
+  {
+  }
+  /* USER CODE END NonMaskableInt_IRQn 1 */
+}
+
+/**
+  * @brief This function handles Hard fault interrupt.
+  */
+void HardFault_Handler(void)
+{
+  /* USER CODE BEGIN HardFault_IRQn 0 */
+
+  /* USER CODE END HardFault_IRQn 0 */
+  while (1)
+  {
+    /* USER CODE BEGIN W1_HardFault_IRQn 0 */
+    /* USER CODE END W1_HardFault_IRQn 0 */
+  }
+}
+
+/**
+  * @brief This function handles Memory management fault.
+  */
+void MemManage_Handler(void)
+{
+  /* USER CODE BEGIN MemoryManagement_IRQn 0 */
+
+  /* USER CODE END MemoryManagement_IRQn 0 */
+  while (1)
+  {
+    /* USER CODE BEGIN W1_MemoryManagement_IRQn 0 */
+    /* USER CODE END W1_MemoryManagement_IRQn 0 */
+  }
+}
+
+/**
+  * @brief This function handles Prefetch fault, memory access fault.
+  */
+void BusFault_Handler(void)
+{
+  /* USER CODE BEGIN BusFault_IRQn 0 */
+
+  /* USER CODE END BusFault_IRQn 0 */
+  while (1)
+  {
+    /* USER CODE BEGIN W1_BusFault_IRQn 0 */
+    /* USER CODE END W1_BusFault_IRQn 0 */
+  }
+}
+
+/**
+  * @brief This function handles Undefined instruction or illegal state.
+  */
+void UsageFault_Handler(void)
+{
+  /* USER CODE BEGIN UsageFault_IRQn 0 */
+
+  /* USER CODE END UsageFault_IRQn 0 */
+  while (1)
+  {
+    /* USER CODE BEGIN W1_UsageFault_IRQn 0 */
+    /* USER CODE END W1_UsageFault_IRQn 0 */
+  }
+}
+
+/**
+  * @brief This function handles System service call via SWI instruction.
+  */
+void SVC_Handler(void)
+{
+  /* USER CODE BEGIN SVCall_IRQn 0 */
+
+  /* USER CODE END SVCall_IRQn 0 */
+  /* USER CODE BEGIN SVCall_IRQn 1 */
+
+  /* USER CODE END SVCall_IRQn 1 */
+}
+
+/**
+  * @brief This function handles Debug monitor.
+  */
+void DebugMon_Handler(void)
+{
+  /* USER CODE BEGIN DebugMonitor_IRQn 0 */
+
+  /* USER CODE END DebugMonitor_IRQn 0 */
+  /* USER CODE BEGIN DebugMonitor_IRQn 1 */
+
+  /* USER CODE END DebugMonitor_IRQn 1 */
+}
+
+/**
+  * @brief This function handles Pendable request for system service.
+  */
+void PendSV_Handler(void)
+{
+  /* USER CODE BEGIN PendSV_IRQn 0 */
+
+  /* USER CODE END PendSV_IRQn 0 */
+  /* USER CODE BEGIN PendSV_IRQn 1 */
+
+  /* USER CODE END PendSV_IRQn 1 */
+}
+
+/**
+  * @brief This function handles System tick timer.
+  */
+void SysTick_Handler(void)
+{
+  /* USER CODE BEGIN SysTick_IRQn 0 */
+
+  /* USER CODE END SysTick_IRQn 0 */
+
+  /* USER CODE BEGIN SysTick_IRQn 1 */
+
+  /* USER CODE END SysTick_IRQn 1 */
+}
+
+/******************************************************************************/
+/* STM32F1xx Peripheral Interrupt Handlers                                    */
+/* Add here the Interrupt Handlers for the used peripherals.                  */
+/* For the available peripheral interrupt handler names,                      */
+/* please refer to the startup file (startup_stm32f1xx.s).                    */
+/******************************************************************************/
+
+/**
+  * @brief This function handles DMA1 channel3 global interrupt.
+  */
+void DMA1_Channel3_IRQHandler(void)
+{
+  /* USER CODE BEGIN DMA1_Channel3_IRQn 0 */
+
+  /* USER CODE END DMA1_Channel3_IRQn 0 */
+  HAL_DMA_IRQHandler(&hdma_usart3_rx);
+  /* USER CODE BEGIN DMA1_Channel3_IRQn 1 */
+
+  /* USER CODE END DMA1_Channel3_IRQn 1 */
+}
+
+/**
+  * @brief This function handles USB high priority or CAN TX interrupts.
+  */
+void USB_HP_CAN1_TX_IRQHandler(void)
+{
+  /* USER CODE BEGIN USB_HP_CAN1_TX_IRQn 0 */
+
+  /* USER CODE END USB_HP_CAN1_TX_IRQn 0 */
+  HAL_CAN_IRQHandler(&hcan);
+  /* USER CODE BEGIN USB_HP_CAN1_TX_IRQn 1 */
+
+  /* USER CODE END USB_HP_CAN1_TX_IRQn 1 */
+}
+
+/**
+  * @brief This function handles USB low priority or CAN RX0 interrupts.
+  */
+void USB_LP_CAN1_RX0_IRQHandler(void)
+{
+  /* USER CODE BEGIN USB_LP_CAN1_RX0_IRQn 0 */
+
+  /* USER CODE END USB_LP_CAN1_RX0_IRQn 0 */
+  HAL_CAN_IRQHandler(&hcan);
+  /* USER CODE BEGIN USB_LP_CAN1_RX0_IRQn 1 */
+
+  /* USER CODE END USB_LP_CAN1_RX0_IRQn 1 */
+}
+
+/**
+  * @brief This function handles CAN SCE interrupt.
+  */
+void CAN1_SCE_IRQHandler(void)
+{
+  /* USER CODE BEGIN CAN1_SCE_IRQn 0 */
+
+  /* USER CODE END CAN1_SCE_IRQn 0 */
+  HAL_CAN_IRQHandler(&hcan);
+  /* USER CODE BEGIN CAN1_SCE_IRQn 1 */
+
+  /* USER CODE END CAN1_SCE_IRQn 1 */
+}
+
+/**
+  * @brief This function handles USART3 global interrupt.
+  */
+void USART3_IRQHandler(void)
+{
+  /* USER CODE BEGIN USART3_IRQn 0 */
+//	HAL_Delay(5);
+
+  /* USER CODE END USART3_IRQn 0 */
+  HAL_UART_IRQHandler(&huart3);
+  /* USER CODE BEGIN USART3_IRQn 1 */
+
+  /* USER CODE END USART3_IRQn 1 */
+}
+
+/**
+  * @brief This function handles TIM8 update interrupt and TIM13 global interrupt.
+  */
+void TIM8_UP_TIM13_IRQHandler(void)
+{
+  /* USER CODE BEGIN TIM8_UP_TIM13_IRQn 0 */
+
+  /* USER CODE END TIM8_UP_TIM13_IRQn 0 */
+  HAL_TIM_IRQHandler(&htim8);
+  /* USER CODE BEGIN TIM8_UP_TIM13_IRQn 1 */
+
+  /* USER CODE END TIM8_UP_TIM13_IRQn 1 */
+}
+
+/**
+  * @brief This function handles TIM7 global interrupt.
+  */
+void TIM7_IRQHandler(void)
+{
+  /* USER CODE BEGIN TIM7_IRQn 0 */
+	REQUESTER_Pulse_TIM_Handler();
+  /* USER CODE END TIM7_IRQn 0 */
+  HAL_TIM_IRQHandler(&htim7);
+  /* USER CODE BEGIN TIM7_IRQn 1 */
+
+  /* USER CODE END TIM7_IRQn 1 */
+}
+
+/**
+  * @brief This function handles DMA2 channel4 and channel5 global interrupts.
+  */
+void DMA2_Channel4_5_IRQHandler(void)
+{
+  /* USER CODE BEGIN DMA2_Channel4_5_IRQn 0 */
+
+  /* USER CODE END DMA2_Channel4_5_IRQn 0 */
+  HAL_DMA_IRQHandler(&hdma_sdio);
+  /* USER CODE BEGIN DMA2_Channel4_5_IRQn 1 */
+
+  /* USER CODE END DMA2_Channel4_5_IRQn 1 */
+}
+
+/* USER CODE BEGIN 1 */
+void EXTI9_5_IRQHandler(void)
+{
+  /* USER CODE BEGIN DMA2_Channel4_5_IRQn 0 */
+
+  /* USER CODE END DMA2_Channel4_5_IRQn 0 */
+  //HAL_GPIO_EXTI_IRQHandler(SD_DETECT_PIN);
+  /* USER CODE BEGIN DMA2_Channel4_5_IRQn 1 */
+	//BSP_SD_DetectIT();
+  /* USER CODE END DMA2_Channel4_5_IRQn 1 */
+}
+/* USER CODE END 1 */

Core/Src/system_stm32f1xx.c

@@ -0,0 +1,408 @@
+/**
+  ******************************************************************************
+  * @file    system_stm32f1xx.c
+  * @author  MCD Application Team
+  * @brief   CMSIS Cortex-M3 Device Peripheral Access Layer System Source File.
+  * 
+  * 1.  This file provides two functions and one global variable to be called from 
+  *     user application:
+  *      - SystemInit(): Setups the system clock (System clock source, PLL Multiplier
+  *                      factors, AHB/APBx prescalers and Flash settings). 
+  *                      This function is called at startup just after reset and 
+  *                      before branch to main program. This call is made inside
+  *                      the "startup_stm32f1xx_xx.s" file.
+  *
+  *      - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
+  *                                  by the user application to setup the SysTick 
+  *                                  timer or configure other parameters.
+  *                                     
+  *      - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
+  *                                 be called whenever the core clock is changed
+  *                                 during program execution.
+  *
+  * 2. After each device reset the HSI (8 MHz) is used as system clock source.
+  *    Then SystemInit() function is called, in "startup_stm32f1xx_xx.s" file, to
+  *    configure the system clock before to branch to main program.
+  *
+  * 4. The default value of HSE crystal is set to 8 MHz (or 25 MHz, depending on
+  *    the product used), refer to "HSE_VALUE". 
+  *    When HSE is used as system clock source, directly or through PLL, and you
+  *    are using different crystal you have to adapt the HSE value to your own
+  *    configuration.
+  *        
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/** @addtogroup CMSIS
+  * @{
+  */
+
+/** @addtogroup stm32f1xx_system
+  * @{
+  */  
+  
+/** @addtogroup STM32F1xx_System_Private_Includes
+  * @{
+  */
+
+#include "stm32f1xx.h"
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F1xx_System_Private_TypesDefinitions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F1xx_System_Private_Defines
+  * @{
+  */
+
+#if !defined  (HSE_VALUE) 
+  #define HSE_VALUE               8000000U /*!< Default value of the External oscillator in Hz.
+                                                This value can be provided and adapted by the user application. */
+#endif /* HSE_VALUE */
+
+#if !defined  (HSI_VALUE)
+  #define HSI_VALUE               8000000U /*!< Default value of the Internal oscillator in Hz.
+                                                This value can be provided and adapted by the user application. */
+#endif /* HSI_VALUE */
+
+/*!< Uncomment the following line if you need to use external SRAM  */ 
+#if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG)
+/* #define DATA_IN_ExtSRAM */
+#endif /* STM32F100xE || STM32F101xE || STM32F101xG || STM32F103xE || STM32F103xG */
+
+/* Note: Following vector table addresses must be defined in line with linker
+         configuration. */
+/*!< Uncomment the following line if you need to relocate the vector table
+     anywhere in Flash or Sram, else the vector table is kept at the automatic
+     remap of boot address selected */
+/* #define USER_VECT_TAB_ADDRESS */
+
+#if defined(USER_VECT_TAB_ADDRESS)
+/*!< Uncomment the following line if you need to relocate your vector Table
+     in Sram else user remap will be done in Flash. */
+/* #define VECT_TAB_SRAM */
+#if defined(VECT_TAB_SRAM)
+#define VECT_TAB_BASE_ADDRESS   SRAM_BASE       /*!< Vector Table base address field.
+                                                     This value must be a multiple of 0x200. */
+#define VECT_TAB_OFFSET         0x0000a000U     /*!< Vector Table base offset field.
+                                                     This value must be a multiple of 0x200. */
+#else
+#define VECT_TAB_BASE_ADDRESS   FLASH_BASE      /*!< Vector Table base address field.
+                                                     This value must be a multiple of 0x200. */
+#define VECT_TAB_OFFSET         0x00000000U     /*!< Vector Table base offset field.
+                                                     This value must be a multiple of 0x200. */
+#endif /* VECT_TAB_SRAM */
+#endif /* USER_VECT_TAB_ADDRESS */
+
+/******************************************************************************/
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F1xx_System_Private_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F1xx_System_Private_Variables
+  * @{
+  */
+
+  /* This variable is updated in three ways:
+      1) by calling CMSIS function SystemCoreClockUpdate()
+      2) by calling HAL API function HAL_RCC_GetHCLKFreq()
+      3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency 
+         Note: If you use this function to configure the system clock; then there
+               is no need to call the 2 first functions listed above, since SystemCoreClock
+               variable is updated automatically.
+  */
+uint32_t SystemCoreClock = 16000000;
+const uint8_t AHBPrescTable[16U] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
+const uint8_t APBPrescTable[8U] =  {0, 0, 0, 0, 1, 2, 3, 4};
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F1xx_System_Private_FunctionPrototypes
+  * @{
+  */
+
+#if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG)
+#ifdef DATA_IN_ExtSRAM
+  static void SystemInit_ExtMemCtl(void); 
+#endif /* DATA_IN_ExtSRAM */
+#endif /* STM32F100xE || STM32F101xE || STM32F101xG || STM32F103xE || STM32F103xG */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F1xx_System_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief  Setup the microcontroller system
+  *         Initialize the Embedded Flash Interface, the PLL and update the 
+  *         SystemCoreClock variable.
+  * @note   This function should be used only after reset.
+  * @param  None
+  * @retval None
+  */
+void SystemInit (void)
+{
+#if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG)
+  #ifdef DATA_IN_ExtSRAM
+    SystemInit_ExtMemCtl(); 
+  #endif /* DATA_IN_ExtSRAM */
+#endif 
+
+  /* Configure the Vector Table location -------------------------------------*/
+#if defined(USER_VECT_TAB_ADDRESS)
+  SCB->VTOR = VECT_TAB_BASE_ADDRESS | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM. */
+#endif /* USER_VECT_TAB_ADDRESS */
+}
+
+/**
+  * @brief  Update SystemCoreClock variable according to Clock Register Values.
+  *         The SystemCoreClock variable contains the core clock (HCLK), it can
+  *         be used by the user application to setup the SysTick timer or configure
+  *         other parameters.
+  *           
+  * @note   Each time the core clock (HCLK) changes, this function must be called
+  *         to update SystemCoreClock variable value. Otherwise, any configuration
+  *         based on this variable will be incorrect.         
+  *     
+  * @note   - The system frequency computed by this function is not the real 
+  *           frequency in the chip. It is calculated based on the predefined 
+  *           constant and the selected clock source:
+  *             
+  *           - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
+  *                                              
+  *           - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
+  *                          
+  *           - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) 
+  *             or HSI_VALUE(*) multiplied by the PLL factors.
+  *         
+  *         (*) HSI_VALUE is a constant defined in stm32f1xx.h file (default value
+  *             8 MHz) but the real value may vary depending on the variations
+  *             in voltage and temperature.   
+  *    
+  *         (**) HSE_VALUE is a constant defined in stm32f1xx.h file (default value
+  *              8 MHz or 25 MHz, depending on the product used), user has to ensure
+  *              that HSE_VALUE is same as the real frequency of the crystal used.
+  *              Otherwise, this function may have wrong result.
+  *                
+  *         - The result of this function could be not correct when using fractional
+  *           value for HSE crystal.
+  * @param  None
+  * @retval None
+  */
+void SystemCoreClockUpdate (void)
+{
+  uint32_t tmp = 0U, pllmull = 0U, pllsource = 0U;
+
+#if defined(STM32F105xC) || defined(STM32F107xC)
+  uint32_t prediv1source = 0U, prediv1factor = 0U, prediv2factor = 0U, pll2mull = 0U;
+#endif /* STM32F105xC */
+
+#if defined(STM32F100xB) || defined(STM32F100xE)
+  uint32_t prediv1factor = 0U;
+#endif /* STM32F100xB or STM32F100xE */
+    
+  /* Get SYSCLK source -------------------------------------------------------*/
+  tmp = RCC->CFGR & RCC_CFGR_SWS;
+  
+  switch (tmp)
+  {
+    case 0x00U:  /* HSI used as system clock */
+      SystemCoreClock = HSI_VALUE;
+      break;
+    case 0x04U:  /* HSE used as system clock */
+      SystemCoreClock = HSE_VALUE;
+      break;
+    case 0x08U:  /* PLL used as system clock */
+
+      /* Get PLL clock source and multiplication factor ----------------------*/
+      pllmull = RCC->CFGR & RCC_CFGR_PLLMULL;
+      pllsource = RCC->CFGR & RCC_CFGR_PLLSRC;
+      
+#if !defined(STM32F105xC) && !defined(STM32F107xC)      
+      pllmull = ( pllmull >> 18U) + 2U;
+      
+      if (pllsource == 0x00U)
+      {
+        /* HSI oscillator clock divided by 2 selected as PLL clock entry */
+        SystemCoreClock = (HSI_VALUE >> 1U) * pllmull;
+      }
+      else
+      {
+ #if defined(STM32F100xB) || defined(STM32F100xE)
+       prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1U;
+       /* HSE oscillator clock selected as PREDIV1 clock entry */
+       SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; 
+ #else
+        /* HSE selected as PLL clock entry */
+        if ((RCC->CFGR & RCC_CFGR_PLLXTPRE) != (uint32_t)RESET)
+        {/* HSE oscillator clock divided by 2 */
+          SystemCoreClock = (HSE_VALUE >> 1U) * pllmull;
+        }
+        else
+        {
+          SystemCoreClock = HSE_VALUE * pllmull;
+        }
+ #endif
+      }
+#else
+      pllmull = pllmull >> 18U;
+      
+      if (pllmull != 0x0DU)
+      {
+         pllmull += 2U;
+      }
+      else
+      { /* PLL multiplication factor = PLL input clock * 6.5 */
+        pllmull = 13U / 2U; 
+      }
+            
+      if (pllsource == 0x00U)
+      {
+        /* HSI oscillator clock divided by 2 selected as PLL clock entry */
+        SystemCoreClock = (HSI_VALUE >> 1U) * pllmull;
+      }
+      else
+      {/* PREDIV1 selected as PLL clock entry */
+        
+        /* Get PREDIV1 clock source and division factor */
+        prediv1source = RCC->CFGR2 & RCC_CFGR2_PREDIV1SRC;
+        prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1U;
+        
+        if (prediv1source == 0U)
+        { 
+          /* HSE oscillator clock selected as PREDIV1 clock entry */
+          SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull;          
+        }
+        else
+        {/* PLL2 clock selected as PREDIV1 clock entry */
+          
+          /* Get PREDIV2 division factor and PLL2 multiplication factor */
+          prediv2factor = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> 4U) + 1U;
+          pll2mull = ((RCC->CFGR2 & RCC_CFGR2_PLL2MUL) >> 8U) + 2U; 
+          SystemCoreClock = (((HSE_VALUE / prediv2factor) * pll2mull) / prediv1factor) * pllmull;                         
+        }
+      }
+#endif /* STM32F105xC */ 
+      break;
+
+    default:
+      SystemCoreClock = HSI_VALUE;
+      break;
+  }
+  
+  /* Compute HCLK clock frequency ----------------*/
+  /* Get HCLK prescaler */
+  tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4U)];
+  /* HCLK clock frequency */
+  SystemCoreClock >>= tmp;  
+}
+
+#if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG)
+/**
+  * @brief  Setup the external memory controller. Called in startup_stm32f1xx.s 
+  *          before jump to __main
+  * @param  None
+  * @retval None
+  */ 
+#ifdef DATA_IN_ExtSRAM
+/**
+  * @brief  Setup the external memory controller. 
+  *         Called in startup_stm32f1xx_xx.s/.c before jump to main.
+  *         This function configures the external SRAM mounted on STM3210E-EVAL
+  *         board (STM32 High density devices). This SRAM will be used as program
+  *         data memory (including heap and stack).
+  * @param  None
+  * @retval None
+  */ 
+void SystemInit_ExtMemCtl(void) 
+{
+  __IO uint32_t tmpreg;
+  /*!< FSMC Bank1 NOR/SRAM3 is used for the STM3210E-EVAL, if another Bank is 
+    required, then adjust the Register Addresses */
+
+  /* Enable FSMC clock */
+  RCC->AHBENR = 0x00000114U;
+
+  /* Delay after an RCC peripheral clock enabling */
+  tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_FSMCEN);
+  
+  /* Enable GPIOD, GPIOE, GPIOF and GPIOG clocks */
+  RCC->APB2ENR = 0x000001E0U;
+  
+  /* Delay after an RCC peripheral clock enabling */
+  tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPDEN);
+
+  (void)(tmpreg);
+  
+/* ---------------  SRAM Data lines, NOE and NWE configuration ---------------*/
+/*----------------  SRAM Address lines configuration -------------------------*/
+/*----------------  NOE and NWE configuration --------------------------------*/  
+/*----------------  NE3 configuration ----------------------------------------*/
+/*----------------  NBL0, NBL1 configuration ---------------------------------*/
+  
+  GPIOD->CRL = 0x44BB44BBU;  
+  GPIOD->CRH = 0xBBBBBBBBU;
+
+  GPIOE->CRL = 0xB44444BBU;  
+  GPIOE->CRH = 0xBBBBBBBBU;
+
+  GPIOF->CRL = 0x44BBBBBBU;  
+  GPIOF->CRH = 0xBBBB4444U;
+
+  GPIOG->CRL = 0x44BBBBBBU;  
+  GPIOG->CRH = 0x444B4B44U;
+   
+/*----------------  FSMC Configuration ---------------------------------------*/  
+/*----------------  Enable FSMC Bank1_SRAM Bank ------------------------------*/
+  
+  FSMC_Bank1->BTCR[4U] = 0x00001091U;
+  FSMC_Bank1->BTCR[5U] = 0x00110212U;
+}
+#endif /* DATA_IN_ExtSRAM */
+#endif /* STM32F100xE || STM32F101xE || STM32F101xG || STM32F103xE || STM32F103xG */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+  
+/**
+  * @}
+  */    
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Core/Src/tim.c

@@ -0,0 +1,104 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    tim.c
+  * @brief   This file provides code for the configuration
+  *          of the TIM instances.
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+/* Includes ------------------------------------------------------------------*/
+#include "tim.h"
+
+/* USER CODE BEGIN 0 */
+
+/* USER CODE END 0 */
+
+TIM_HandleTypeDef htim7;
+
+/* TIM7 init function */
+void MX_TIM7_Init(void)
+{
+
+  /* USER CODE BEGIN TIM7_Init 0 */
+
+  /* USER CODE END TIM7_Init 0 */
+
+  TIM_MasterConfigTypeDef sMasterConfig = {0};
+
+  /* USER CODE BEGIN TIM7_Init 1 */
+
+  /* USER CODE END TIM7_Init 1 */
+  htim7.Instance = TIM7;
+  htim7.Init.Prescaler = TIM_REQUESTER_Prescaler-1;
+  htim7.Init.CounterMode = TIM_COUNTERMODE_UP;
+  htim7.Init.Period = 1000;
+  htim7.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;
+  if (HAL_TIM_Base_Init(&htim7) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  sMasterConfig.MasterOutputTrigger = TIM_TRGO_RESET;
+  sMasterConfig.MasterSlaveMode = TIM_MASTERSLAVEMODE_DISABLE;
+  if (HAL_TIMEx_MasterConfigSynchronization(&htim7, &sMasterConfig) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN TIM7_Init 2 */
+
+  /* USER CODE END TIM7_Init 2 */
+
+}
+
+void HAL_TIM_Base_MspInit(TIM_HandleTypeDef* tim_baseHandle)
+{
+
+  if(tim_baseHandle->Instance==TIM7)
+  {
+  /* USER CODE BEGIN TIM7_MspInit 0 */
+
+  /* USER CODE END TIM7_MspInit 0 */
+    /* TIM7 clock enable */
+    __HAL_RCC_TIM7_CLK_ENABLE();
+
+    /* TIM7 interrupt Init */
+    HAL_NVIC_SetPriority(TIM7_IRQn, 0, 0);
+    HAL_NVIC_EnableIRQ(TIM7_IRQn);
+  /* USER CODE BEGIN TIM7_MspInit 1 */
+
+  /* USER CODE END TIM7_MspInit 1 */
+  }
+}
+
+void HAL_TIM_Base_MspDeInit(TIM_HandleTypeDef* tim_baseHandle)
+{
+
+  if(tim_baseHandle->Instance==TIM7)
+  {
+  /* USER CODE BEGIN TIM7_MspDeInit 0 */
+
+  /* USER CODE END TIM7_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_TIM7_CLK_DISABLE();
+
+    /* TIM7 interrupt Deinit */
+    HAL_NVIC_DisableIRQ(TIM7_IRQn);
+  /* USER CODE BEGIN TIM7_MspDeInit 1 */
+
+  /* USER CODE END TIM7_MspDeInit 1 */
+  }
+}
+
+/* USER CODE BEGIN 1 */
+
+/* USER CODE END 1 */

Core/Src/usart.c

@@ -0,0 +1,258 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    usart.c
+  * @brief   This file provides code for the configuration
+  *          of the USART instances.
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2024 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+/* Includes ------------------------------------------------------------------*/
+#include "usart.h"
+
+/* USER CODE BEGIN 0 */
+
+/* USER CODE END 0 */
+
+UART_HandleTypeDef huart3;
+DMA_HandleTypeDef hdma_usart3_rx;
+
+/* USART3 init function */
+
+void MX_USART3_UART_Init(void)
+{
+
+  /* USER CODE BEGIN USART3_Init 0 */
+
+  /* USER CODE END USART3_Init 0 */
+
+  /* USER CODE BEGIN USART3_Init 1 */
+			//256000*4
+  /* USER CODE END USART3_Init 1 */
+  huart3.Instance = USART3;
+  huart3.Init.BaudRate = 9600*2;
+  huart3.Init.WordLength = UART_WORDLENGTH_8B;
+  huart3.Init.StopBits = UART_STOPBITS_1;
+  huart3.Init.Parity = UART_PARITY_NONE;
+  huart3.Init.Mode = UART_MODE_TX_RX;
+  huart3.Init.HwFlowCtl = UART_HWCONTROL_NONE;
+  huart3.Init.OverSampling = UART_OVERSAMPLING_16;
+  if (HAL_UART_Init(&huart3) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN USART3_Init 2 */
+
+  /* USER CODE END USART3_Init 2 */
+
+}
+
+void HAL_UART_MspInit(UART_HandleTypeDef* uartHandle)
+{
+
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+  if(uartHandle->Instance==USART3)
+  {
+  /* USER CODE BEGIN USART3_MspInit 0 */
+
+  /* USER CODE END USART3_MspInit 0 */
+    /* USART3 clock enable */
+    __HAL_RCC_USART3_CLK_ENABLE();
+
+    __HAL_RCC_GPIOB_CLK_ENABLE();
+    /**USART3 GPIO Configuration
+    PB10     ------> USART3_TX
+    PB11     ------> USART3_RX
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_10;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+    HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_11;
+    GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+    /* USART3 DMA Init */
+    /* USART3_RX Init */
+    hdma_usart3_rx.Instance = DMA1_Channel3;
+    hdma_usart3_rx.Init.Direction = DMA_PERIPH_TO_MEMORY;
+    hdma_usart3_rx.Init.PeriphInc = DMA_PINC_DISABLE;
+    hdma_usart3_rx.Init.MemInc = DMA_MINC_ENABLE;
+    hdma_usart3_rx.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
+    hdma_usart3_rx.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
+    hdma_usart3_rx.Init.Mode = DMA_CIRCULAR;
+    hdma_usart3_rx.Init.Priority = DMA_PRIORITY_LOW;
+    if (HAL_DMA_Init(&hdma_usart3_rx) != HAL_OK)
+    {
+      Error_Handler();
+    }
+
+    __HAL_LINKDMA(uartHandle,hdmarx,hdma_usart3_rx);
+
+    /* USART3 interrupt Init */
+    HAL_NVIC_SetPriority(USART3_IRQn, 0, 0);
+    HAL_NVIC_EnableIRQ(USART3_IRQn);
+  /* USER CODE BEGIN USART3_MspInit 1 */
+
+  /* USER CODE END USART3_MspInit 1 */
+  }
+}
+
+void HAL_UART_MspDeInit(UART_HandleTypeDef* uartHandle)
+{
+
+  if(uartHandle->Instance==USART3)
+  {
+  /* USER CODE BEGIN USART3_MspDeInit 0 */
+
+  /* USER CODE END USART3_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_USART3_CLK_DISABLE();
+
+    /**USART3 GPIO Configuration
+    PB10     ------> USART3_TX
+    PB11     ------> USART3_RX
+    */
+    HAL_GPIO_DeInit(GPIOB, GPIO_PIN_10|GPIO_PIN_11);
+
+    /* USART3 DMA DeInit */
+    HAL_DMA_DeInit(uartHandle->hdmarx);
+
+    /* USART3 interrupt Deinit */
+    HAL_NVIC_DisableIRQ(USART3_IRQn);
+  /* USER CODE BEGIN USART3_MspDeInit 1 */
+
+  /* USER CODE END USART3_MspDeInit 1 */
+  }
+}
+
+/* USER CODE BEGIN 1 */
+
+
+// CUSTOM UART INIT
+//void User_UART_Init(UART_HandleTypeDef* huart, DMA_HandleTypeDef *DMAhuart, struct UARTSettings *uuart)
+//{ // function takes uart handler, dma handler and setting structure for init
+//	
+//	// get setting for uart from UARTSettings structure
+//	huart->Instance = uuart->UARTx;
+//  huart->Init.BaudRate = uuart->UART_Speed*2;
+//	
+//	// everything else is default (for now, maybe this settings would be added in UARTSettings structure later)
+//  huart->Init.WordLength = UART_WORDLENGTH_8B;
+//  huart->Init.StopBits = UART_STOPBITS_1;
+//  huart->Init.Parity = UART_PARITY_NONE;
+//  huart->Init.Mode = UART_MODE_TX_RX;
+//  huart->Init.HwFlowCtl = UART_HWCONTROL_NONE;
+//  huart->Init.OverSampling = UART_OVERSAMPLING_16;
+//  if (HAL_UART_Init(huart) != HAL_OK)
+//  {
+//    Error_Handler();
+//  }
+//	
+//	// init gpio from UARTSettings structure
+//	UART_GPIO_Init(uuart->GPIOx, uuart->GPIO_PIN_RX, uuart->GPIO_PIN_TX);
+//	// init dma from UARTSettings structure if need
+//	if (uuart->DMAChannel != 0)
+//		UART_DMA_Init(huart, DMAhuart, uuart->DMAChannel);
+//}
+
+
+//void UART_GPIO_Init(GPIO_TypeDef *GPIOx, uint16_t GPIO_PIN_RX, uint16_t GPIO_PIN_TX)
+//{ // function takes port and pins (for rx and tx)
+//  GPIO_InitTypeDef GPIO_InitStruct = {0};
+//	
+//	// choose port for enable clock
+//	if (GPIOx==GPIOA)
+//		__HAL_RCC_GPIOA_CLK_ENABLE();
+//	else if (GPIOx==GPIOB)
+//		__HAL_RCC_GPIOB_CLK_ENABLE();
+//	else if (GPIOx==GPIOC)
+//		__HAL_RCC_GPIOC_CLK_ENABLE();
+//	else if (GPIOx==GPIOD)
+//		__HAL_RCC_GPIOD_CLK_ENABLE();
+//	
+//// USART3 GPIO Configuration
+////GPIO_PIN_TX ------> USART_TX
+//	GPIO_InitStruct.Pin = GPIO_PIN_TX;
+//	GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+//	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+//	HAL_GPIO_Init(GPIOx, &GPIO_InitStruct);
+
+////	GPIO_PIN_RX ------> USART_RX	
+//	GPIO_InitStruct.Pin = GPIO_PIN_RX;
+//	GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+//	GPIO_InitStruct.Pull = GPIO_NOPULL;
+//	HAL_GPIO_Init(GPIOx, &GPIO_InitStruct);
+//}
+
+
+//void UART_DMA_Init(UART_HandleTypeDef *huart, DMA_HandleTypeDef *hdma_rx, DMA_Channel_TypeDef *DMAhuart)
+//{ // function takes uart and dma handlers and dmachannel for uart
+//	// for now only dma rx is supported, tx maybe later if needed
+//	
+//	/* USART3 DMA Init */
+//	/* USART3_RX Init */
+//	hdma_rx->Instance = DMAhuart;
+//	hdma_rx->Init.Direction = DMA_PERIPH_TO_MEMORY;
+//	hdma_rx->Init.PeriphInc = DMA_PINC_DISABLE;
+//	hdma_rx->Init.MemInc = DMA_MINC_ENABLE;
+//	hdma_rx->Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
+//	hdma_rx->Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
+//	hdma_rx->Init.Mode = DMA_CIRCULAR;
+//	hdma_rx->Init.Priority = DMA_PRIORITY_LOW;
+//	if (HAL_DMA_Init(hdma_rx) != HAL_OK)
+//	{
+//		Error_Handler();
+//	}
+
+//	__USER_LINKDMA(huart,hdmarx,hdma_rx); 
+//	// __USER_LINKDMA is need because __HAL_LINKDMA is written for global defined hdma_rx
+//	// so you get error because hal uses . insted of ->
+//}
+
+
+
+//void HAL_UART_MspInit(UART_HandleTypeDef* huart) // redefine hal function
+//{ // left only rcc and interrupt init for USART_1,2,3 (maybe UART_4,5 need to be added)
+//	// GPIO and DMA init was move to their own functions
+//  if(huart->Instance==USART3)
+//  {
+//	/* USART3 clock enable */
+//	__HAL_RCC_USART3_CLK_ENABLE();
+//	
+//	/* USART3 interrupt Init */
+//	HAL_NVIC_SetPriority(USART3_IRQn, 0, 0);
+//  HAL_NVIC_EnableIRQ(USART3_IRQn);
+//  }
+//	else if(huart->Instance==USART2)
+//  {
+//	/* USART3 clock enable */
+//	__HAL_RCC_USART2_CLK_ENABLE();
+//	
+//	/* USART3 interrupt Init */
+//	HAL_NVIC_SetPriority(USART2_IRQn, 0, 0);
+//  HAL_NVIC_EnableIRQ(USART2_IRQn);
+//  }
+//	else if(huart->Instance==USART1)
+//  {
+//	/* USART3 clock enable */
+//	__HAL_RCC_USART1_CLK_ENABLE();
+//	
+//	/* USART3 interrupt Init */
+//	HAL_NVIC_SetPriority(USART1_IRQn, 0, 0);
+//  HAL_NVIC_EnableIRQ(USART1_IRQn);
+//  }
+//}
+/* USER CODE END 1 */

Drivers/CMSIS/Core/Include/cmsis_armcc.h

@@ -0,0 +1,865 @@
+/**************************************************************************//**
+ * @file     cmsis_armcc.h
+ * @brief    CMSIS compiler ARMCC (Arm Compiler 5) header file
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef __CMSIS_ARMCC_H
+#define __CMSIS_ARMCC_H
+
+
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 400677)
+  #error "Please use Arm Compiler Toolchain V4.0.677 or later!"
+#endif
+
+/* CMSIS compiler control architecture macros */
+#if ((defined (__TARGET_ARCH_6_M  ) && (__TARGET_ARCH_6_M   == 1)) || \
+     (defined (__TARGET_ARCH_6S_M ) && (__TARGET_ARCH_6S_M  == 1))   )
+  #define __ARM_ARCH_6M__           1
+#endif
+
+#if (defined (__TARGET_ARCH_7_M ) && (__TARGET_ARCH_7_M  == 1))
+  #define __ARM_ARCH_7M__           1
+#endif
+
+#if (defined (__TARGET_ARCH_7E_M) && (__TARGET_ARCH_7E_M == 1))
+  #define __ARM_ARCH_7EM__          1
+#endif
+
+  /* __ARM_ARCH_8M_BASE__  not applicable */
+  /* __ARM_ARCH_8M_MAIN__  not applicable */
+
+
+/* CMSIS compiler specific defines */
+#ifndef   __ASM
+  #define __ASM                                  __asm
+#endif
+#ifndef   __INLINE
+  #define __INLINE                               __inline
+#endif
+#ifndef   __STATIC_INLINE
+  #define __STATIC_INLINE                        static __inline
+#endif
+#ifndef   __STATIC_FORCEINLINE                 
+  #define __STATIC_FORCEINLINE                   static __forceinline
+#endif           
+#ifndef   __NO_RETURN
+  #define __NO_RETURN                            __declspec(noreturn)
+#endif
+#ifndef   __USED
+  #define __USED                                 __attribute__((used))
+#endif
+#ifndef   __WEAK
+  #define __WEAK                                 __attribute__((weak))
+#endif
+#ifndef   __PACKED
+  #define __PACKED                               __attribute__((packed))
+#endif
+#ifndef   __PACKED_STRUCT
+  #define __PACKED_STRUCT                        __packed struct
+#endif
+#ifndef   __PACKED_UNION
+  #define __PACKED_UNION                         __packed union
+#endif
+#ifndef   __UNALIGNED_UINT32        /* deprecated */
+  #define __UNALIGNED_UINT32(x)                  (*((__packed uint32_t *)(x)))
+#endif
+#ifndef   __UNALIGNED_UINT16_WRITE
+  #define __UNALIGNED_UINT16_WRITE(addr, val)    ((*((__packed uint16_t *)(addr))) = (val))
+#endif
+#ifndef   __UNALIGNED_UINT16_READ
+  #define __UNALIGNED_UINT16_READ(addr)          (*((const __packed uint16_t *)(addr)))
+#endif
+#ifndef   __UNALIGNED_UINT32_WRITE
+  #define __UNALIGNED_UINT32_WRITE(addr, val)    ((*((__packed uint32_t *)(addr))) = (val))
+#endif
+#ifndef   __UNALIGNED_UINT32_READ
+  #define __UNALIGNED_UINT32_READ(addr)          (*((const __packed uint32_t *)(addr)))
+#endif
+#ifndef   __ALIGNED
+  #define __ALIGNED(x)                           __attribute__((aligned(x)))
+#endif
+#ifndef   __RESTRICT
+  #define __RESTRICT                             __restrict
+#endif
+
+/* ###########################  Core Function Access  ########################### */
+/** \ingroup  CMSIS_Core_FunctionInterface
+    \defgroup CMSIS_Core_RegAccFunctions CMSIS Core Register Access Functions
+  @{
+ */
+
+/**
+  \brief   Enable IRQ Interrupts
+  \details Enables IRQ interrupts by clearing the I-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+/* intrinsic void __enable_irq();     */
+
+
+/**
+  \brief   Disable IRQ Interrupts
+  \details Disables IRQ interrupts by setting the I-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+/* intrinsic void __disable_irq();    */
+
+/**
+  \brief   Get Control Register
+  \details Returns the content of the Control Register.
+  \return               Control Register value
+ */
+__STATIC_INLINE uint32_t __get_CONTROL(void)
+{
+  register uint32_t __regControl         __ASM("control");
+  return(__regControl);
+}
+
+
+/**
+  \brief   Set Control Register
+  \details Writes the given value to the Control Register.
+  \param [in]    control  Control Register value to set
+ */
+__STATIC_INLINE void __set_CONTROL(uint32_t control)
+{
+  register uint32_t __regControl         __ASM("control");
+  __regControl = control;
+}
+
+
+/**
+  \brief   Get IPSR Register
+  \details Returns the content of the IPSR Register.
+  \return               IPSR Register value
+ */
+__STATIC_INLINE uint32_t __get_IPSR(void)
+{
+  register uint32_t __regIPSR          __ASM("ipsr");
+  return(__regIPSR);
+}
+
+
+/**
+  \brief   Get APSR Register
+  \details Returns the content of the APSR Register.
+  \return               APSR Register value
+ */
+__STATIC_INLINE uint32_t __get_APSR(void)
+{
+  register uint32_t __regAPSR          __ASM("apsr");
+  return(__regAPSR);
+}
+
+
+/**
+  \brief   Get xPSR Register
+  \details Returns the content of the xPSR Register.
+  \return               xPSR Register value
+ */
+__STATIC_INLINE uint32_t __get_xPSR(void)
+{
+  register uint32_t __regXPSR          __ASM("xpsr");
+  return(__regXPSR);
+}
+
+
+/**
+  \brief   Get Process Stack Pointer
+  \details Returns the current value of the Process Stack Pointer (PSP).
+  \return               PSP Register value
+ */
+__STATIC_INLINE uint32_t __get_PSP(void)
+{
+  register uint32_t __regProcessStackPointer  __ASM("psp");
+  return(__regProcessStackPointer);
+}
+
+
+/**
+  \brief   Set Process Stack Pointer
+  \details Assigns the given value to the Process Stack Pointer (PSP).
+  \param [in]    topOfProcStack  Process Stack Pointer value to set
+ */
+__STATIC_INLINE void __set_PSP(uint32_t topOfProcStack)
+{
+  register uint32_t __regProcessStackPointer  __ASM("psp");
+  __regProcessStackPointer = topOfProcStack;
+}
+
+
+/**
+  \brief   Get Main Stack Pointer
+  \details Returns the current value of the Main Stack Pointer (MSP).
+  \return               MSP Register value
+ */
+__STATIC_INLINE uint32_t __get_MSP(void)
+{
+  register uint32_t __regMainStackPointer     __ASM("msp");
+  return(__regMainStackPointer);
+}
+
+
+/**
+  \brief   Set Main Stack Pointer
+  \details Assigns the given value to the Main Stack Pointer (MSP).
+  \param [in]    topOfMainStack  Main Stack Pointer value to set
+ */
+__STATIC_INLINE void __set_MSP(uint32_t topOfMainStack)
+{
+  register uint32_t __regMainStackPointer     __ASM("msp");
+  __regMainStackPointer = topOfMainStack;
+}
+
+
+/**
+  \brief   Get Priority Mask
+  \details Returns the current state of the priority mask bit from the Priority Mask Register.
+  \return               Priority Mask value
+ */
+__STATIC_INLINE uint32_t __get_PRIMASK(void)
+{
+  register uint32_t __regPriMask         __ASM("primask");
+  return(__regPriMask);
+}
+
+
+/**
+  \brief   Set Priority Mask
+  \details Assigns the given value to the Priority Mask Register.
+  \param [in]    priMask  Priority Mask
+ */
+__STATIC_INLINE void __set_PRIMASK(uint32_t priMask)
+{
+  register uint32_t __regPriMask         __ASM("primask");
+  __regPriMask = (priMask);
+}
+
+
+#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+     (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+
+/**
+  \brief   Enable FIQ
+  \details Enables FIQ interrupts by clearing the F-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+#define __enable_fault_irq                __enable_fiq
+
+
+/**
+  \brief   Disable FIQ
+  \details Disables FIQ interrupts by setting the F-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+#define __disable_fault_irq               __disable_fiq
+
+
+/**
+  \brief   Get Base Priority
+  \details Returns the current value of the Base Priority register.
+  \return               Base Priority register value
+ */
+__STATIC_INLINE uint32_t  __get_BASEPRI(void)
+{
+  register uint32_t __regBasePri         __ASM("basepri");
+  return(__regBasePri);
+}
+
+
+/**
+  \brief   Set Base Priority
+  \details Assigns the given value to the Base Priority register.
+  \param [in]    basePri  Base Priority value to set
+ */
+__STATIC_INLINE void __set_BASEPRI(uint32_t basePri)
+{
+  register uint32_t __regBasePri         __ASM("basepri");
+  __regBasePri = (basePri & 0xFFU);
+}
+
+
+/**
+  \brief   Set Base Priority with condition
+  \details Assigns the given value to the Base Priority register only if BASEPRI masking is disabled,
+           or the new value increases the BASEPRI priority level.
+  \param [in]    basePri  Base Priority value to set
+ */
+__STATIC_INLINE void __set_BASEPRI_MAX(uint32_t basePri)
+{
+  register uint32_t __regBasePriMax      __ASM("basepri_max");
+  __regBasePriMax = (basePri & 0xFFU);
+}
+
+
+/**
+  \brief   Get Fault Mask
+  \details Returns the current value of the Fault Mask register.
+  \return               Fault Mask register value
+ */
+__STATIC_INLINE uint32_t __get_FAULTMASK(void)
+{
+  register uint32_t __regFaultMask       __ASM("faultmask");
+  return(__regFaultMask);
+}
+
+
+/**
+  \brief   Set Fault Mask
+  \details Assigns the given value to the Fault Mask register.
+  \param [in]    faultMask  Fault Mask value to set
+ */
+__STATIC_INLINE void __set_FAULTMASK(uint32_t faultMask)
+{
+  register uint32_t __regFaultMask       __ASM("faultmask");
+  __regFaultMask = (faultMask & (uint32_t)1U);
+}
+
+#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+           (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+
+
+/**
+  \brief   Get FPSCR
+  \details Returns the current value of the Floating Point Status/Control register.
+  \return               Floating Point Status/Control register value
+ */
+__STATIC_INLINE uint32_t __get_FPSCR(void)
+{
+#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+     (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+  register uint32_t __regfpscr         __ASM("fpscr");
+  return(__regfpscr);
+#else
+   return(0U);
+#endif
+}
+
+
+/**
+  \brief   Set FPSCR
+  \details Assigns the given value to the Floating Point Status/Control register.
+  \param [in]    fpscr  Floating Point Status/Control value to set
+ */
+__STATIC_INLINE void __set_FPSCR(uint32_t fpscr)
+{
+#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+     (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+  register uint32_t __regfpscr         __ASM("fpscr");
+  __regfpscr = (fpscr);
+#else
+  (void)fpscr;
+#endif
+}
+
+
+/*@} end of CMSIS_Core_RegAccFunctions */
+
+
+/* ##########################  Core Instruction Access  ######################### */
+/** \defgroup CMSIS_Core_InstructionInterface CMSIS Core Instruction Interface
+  Access to dedicated instructions
+  @{
+*/
+
+/**
+  \brief   No Operation
+  \details No Operation does nothing. This instruction can be used for code alignment purposes.
+ */
+#define __NOP                             __nop
+
+
+/**
+  \brief   Wait For Interrupt
+  \details Wait For Interrupt is a hint instruction that suspends execution until one of a number of events occurs.
+ */
+#define __WFI                             __wfi
+
+
+/**
+  \brief   Wait For Event
+  \details Wait For Event is a hint instruction that permits the processor to enter
+           a low-power state until one of a number of events occurs.
+ */
+#define __WFE                             __wfe
+
+
+/**
+  \brief   Send Event
+  \details Send Event is a hint instruction. It causes an event to be signaled to the CPU.
+ */
+#define __SEV                             __sev
+
+
+/**
+  \brief   Instruction Synchronization Barrier
+  \details Instruction Synchronization Barrier flushes the pipeline in the processor,
+           so that all instructions following the ISB are fetched from cache or memory,
+           after the instruction has been completed.
+ */
+#define __ISB() do {\
+                   __schedule_barrier();\
+                   __isb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+/**
+  \brief   Data Synchronization Barrier
+  \details Acts as a special kind of Data Memory Barrier.
+           It completes when all explicit memory accesses before this instruction complete.
+ */
+#define __DSB() do {\
+                   __schedule_barrier();\
+                   __dsb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+/**
+  \brief   Data Memory Barrier
+  \details Ensures the apparent order of the explicit memory operations before
+           and after the instruction, without ensuring their completion.
+ */
+#define __DMB() do {\
+                   __schedule_barrier();\
+                   __dmb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+                  
+/**
+  \brief   Reverse byte order (32 bit)
+  \details Reverses the byte order in unsigned integer value. For example, 0x12345678 becomes 0x78563412.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#define __REV                             __rev
+
+
+/**
+  \brief   Reverse byte order (16 bit)
+  \details Reverses the byte order within each halfword of a word. For example, 0x12345678 becomes 0x34127856.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".rev16_text"))) __STATIC_INLINE __ASM uint32_t __REV16(uint32_t value)
+{
+  rev16 r0, r0
+  bx lr
+}
+#endif
+
+
+/**
+  \brief   Reverse byte order (16 bit)
+  \details Reverses the byte order in a 16-bit value and returns the signed 16-bit result. For example, 0x0080 becomes 0x8000.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".revsh_text"))) __STATIC_INLINE __ASM int16_t __REVSH(int16_t value)
+{
+  revsh r0, r0
+  bx lr
+}
+#endif
+
+
+/**
+  \brief   Rotate Right in unsigned value (32 bit)
+  \details Rotate Right (immediate) provides the value of the contents of a register rotated by a variable number of bits.
+  \param [in]    op1  Value to rotate
+  \param [in]    op2  Number of Bits to rotate
+  \return               Rotated value
+ */
+#define __ROR                             __ror
+
+
+/**
+  \brief   Breakpoint
+  \details Causes the processor to enter Debug state.
+           Debug tools can use this to investigate system state when the instruction at a particular address is reached.
+  \param [in]    value  is ignored by the processor.
+                 If required, a debugger can use it to store additional information about the breakpoint.
+ */
+#define __BKPT(value)                       __breakpoint(value)
+
+
+/**
+  \brief   Reverse bit order of value
+  \details Reverses the bit order of the given value.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+     (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+  #define __RBIT                          __rbit
+#else
+__attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value)
+{
+  uint32_t result;
+  uint32_t s = (4U /*sizeof(v)*/ * 8U) - 1U; /* extra shift needed at end */
+
+  result = value;                      /* r will be reversed bits of v; first get LSB of v */
+  for (value >>= 1U; value != 0U; value >>= 1U)
+  {
+    result <<= 1U;
+    result |= value & 1U;
+    s--;
+  }
+  result <<= s;                        /* shift when v's highest bits are zero */
+  return result;
+}
+#endif
+
+
+/**
+  \brief   Count leading zeros
+  \details Counts the number of leading zeros of a data value.
+  \param [in]  value  Value to count the leading zeros
+  \return             number of leading zeros in value
+ */
+#define __CLZ                             __clz
+
+
+#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+     (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+
+/**
+  \brief   LDR Exclusive (8 bit)
+  \details Executes a exclusive LDR instruction for 8 bit value.
+  \param [in]    ptr  Pointer to data
+  \return             value of type uint8_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXB(ptr)                                                        ((uint8_t ) __ldrex(ptr))
+#else
+  #define __LDREXB(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint8_t ) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+
+/**
+  \brief   LDR Exclusive (16 bit)
+  \details Executes a exclusive LDR instruction for 16 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint16_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXH(ptr)                                                        ((uint16_t) __ldrex(ptr))
+#else
+  #define __LDREXH(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint16_t) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+
+/**
+  \brief   LDR Exclusive (32 bit)
+  \details Executes a exclusive LDR instruction for 32 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint32_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXW(ptr)                                                        ((uint32_t ) __ldrex(ptr))
+#else
+  #define __LDREXW(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint32_t ) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+
+/**
+  \brief   STR Exclusive (8 bit)
+  \details Executes a exclusive STR instruction for 8 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXB(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXB(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+
+/**
+  \brief   STR Exclusive (16 bit)
+  \details Executes a exclusive STR instruction for 16 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXH(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXH(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+
+/**
+  \brief   STR Exclusive (32 bit)
+  \details Executes a exclusive STR instruction for 32 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXW(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXW(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+
+/**
+  \brief   Remove the exclusive lock
+  \details Removes the exclusive lock which is created by LDREX.
+ */
+#define __CLREX                           __clrex
+
+
+/**
+  \brief   Signed Saturate
+  \details Saturates a signed value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (1..32)
+  \return             Saturated value
+ */
+#define __SSAT                            __ssat
+
+
+/**
+  \brief   Unsigned Saturate
+  \details Saturates an unsigned value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (0..31)
+  \return             Saturated value
+ */
+#define __USAT                            __usat
+
+
+/**
+  \brief   Rotate Right with Extend (32 bit)
+  \details Moves each bit of a bitstring right by one bit.
+           The carry input is shifted in at the left end of the bitstring.
+  \param [in]    value  Value to rotate
+  \return               Rotated value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".rrx_text"))) __STATIC_INLINE __ASM uint32_t __RRX(uint32_t value)
+{
+  rrx r0, r0
+  bx lr
+}
+#endif
+
+
+/**
+  \brief   LDRT Unprivileged (8 bit)
+  \details Executes a Unprivileged LDRT instruction for 8 bit value.
+  \param [in]    ptr  Pointer to data
+  \return             value of type uint8_t at (*ptr)
+ */
+#define __LDRBT(ptr)                      ((uint8_t )  __ldrt(ptr))
+
+
+/**
+  \brief   LDRT Unprivileged (16 bit)
+  \details Executes a Unprivileged LDRT instruction for 16 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint16_t at (*ptr)
+ */
+#define __LDRHT(ptr)                      ((uint16_t)  __ldrt(ptr))
+
+
+/**
+  \brief   LDRT Unprivileged (32 bit)
+  \details Executes a Unprivileged LDRT instruction for 32 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint32_t at (*ptr)
+ */
+#define __LDRT(ptr)                       ((uint32_t ) __ldrt(ptr))
+
+
+/**
+  \brief   STRT Unprivileged (8 bit)
+  \details Executes a Unprivileged STRT instruction for 8 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+ */
+#define __STRBT(value, ptr)               __strt(value, ptr)
+
+
+/**
+  \brief   STRT Unprivileged (16 bit)
+  \details Executes a Unprivileged STRT instruction for 16 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+ */
+#define __STRHT(value, ptr)               __strt(value, ptr)
+
+
+/**
+  \brief   STRT Unprivileged (32 bit)
+  \details Executes a Unprivileged STRT instruction for 32 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+ */
+#define __STRT(value, ptr)                __strt(value, ptr)
+
+#else  /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+           (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+
+/**
+  \brief   Signed Saturate
+  \details Saturates a signed value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (1..32)
+  \return             Saturated value
+ */
+__attribute__((always_inline)) __STATIC_INLINE int32_t __SSAT(int32_t val, uint32_t sat)
+{
+  if ((sat >= 1U) && (sat <= 32U))
+  {
+    const int32_t max = (int32_t)((1U << (sat - 1U)) - 1U);
+    const int32_t min = -1 - max ;
+    if (val > max)
+    {
+      return max;
+    }
+    else if (val < min)
+    {
+      return min;
+    }
+  }
+  return val;
+}
+
+/**
+  \brief   Unsigned Saturate
+  \details Saturates an unsigned value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (0..31)
+  \return             Saturated value
+ */
+__attribute__((always_inline)) __STATIC_INLINE uint32_t __USAT(int32_t val, uint32_t sat)
+{
+  if (sat <= 31U)
+  {
+    const uint32_t max = ((1U << sat) - 1U);
+    if (val > (int32_t)max)
+    {
+      return max;
+    }
+    else if (val < 0)
+    {
+      return 0U;
+    }
+  }
+  return (uint32_t)val;
+}
+
+#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+           (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+
+/*@}*/ /* end of group CMSIS_Core_InstructionInterface */
+
+
+/* ###################  Compiler specific Intrinsics  ########################### */
+/** \defgroup CMSIS_SIMD_intrinsics CMSIS SIMD Intrinsics
+  Access to dedicated SIMD instructions
+  @{
+*/
+
+#if ((defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+
+#define __SADD8                           __sadd8
+#define __QADD8                           __qadd8
+#define __SHADD8                          __shadd8
+#define __UADD8                           __uadd8
+#define __UQADD8                          __uqadd8
+#define __UHADD8                          __uhadd8
+#define __SSUB8                           __ssub8
+#define __QSUB8                           __qsub8
+#define __SHSUB8                          __shsub8
+#define __USUB8                           __usub8
+#define __UQSUB8                          __uqsub8
+#define __UHSUB8                          __uhsub8
+#define __SADD16                          __sadd16
+#define __QADD16                          __qadd16
+#define __SHADD16                         __shadd16
+#define __UADD16                          __uadd16
+#define __UQADD16                         __uqadd16
+#define __UHADD16                         __uhadd16
+#define __SSUB16                          __ssub16
+#define __QSUB16                          __qsub16
+#define __SHSUB16                         __shsub16
+#define __USUB16                          __usub16
+#define __UQSUB16                         __uqsub16
+#define __UHSUB16                         __uhsub16
+#define __SASX                            __sasx
+#define __QASX                            __qasx
+#define __SHASX                           __shasx
+#define __UASX                            __uasx
+#define __UQASX                           __uqasx
+#define __UHASX                           __uhasx
+#define __SSAX                            __ssax
+#define __QSAX                            __qsax
+#define __SHSAX                           __shsax
+#define __USAX                            __usax
+#define __UQSAX                           __uqsax
+#define __UHSAX                           __uhsax
+#define __USAD8                           __usad8
+#define __USADA8                          __usada8
+#define __SSAT16                          __ssat16
+#define __USAT16                          __usat16
+#define __UXTB16                          __uxtb16
+#define __UXTAB16                         __uxtab16
+#define __SXTB16                          __sxtb16
+#define __SXTAB16                         __sxtab16
+#define __SMUAD                           __smuad
+#define __SMUADX                          __smuadx
+#define __SMLAD                           __smlad
+#define __SMLADX                          __smladx
+#define __SMLALD                          __smlald
+#define __SMLALDX                         __smlaldx
+#define __SMUSD                           __smusd
+#define __SMUSDX                          __smusdx
+#define __SMLSD                           __smlsd
+#define __SMLSDX                          __smlsdx
+#define __SMLSLD                          __smlsld
+#define __SMLSLDX                         __smlsldx
+#define __SEL                             __sel
+#define __QADD                            __qadd
+#define __QSUB                            __qsub
+
+#define __PKHBT(ARG1,ARG2,ARG3)          ( ((((uint32_t)(ARG1))          ) & 0x0000FFFFUL) |  \
+                                           ((((uint32_t)(ARG2)) << (ARG3)) & 0xFFFF0000UL)  )
+
+#define __PKHTB(ARG1,ARG2,ARG3)          ( ((((uint32_t)(ARG1))          ) & 0xFFFF0000UL) |  \
+                                           ((((uint32_t)(ARG2)) >> (ARG3)) & 0x0000FFFFUL)  )
+
+#define __SMMLA(ARG1,ARG2,ARG3)          ( (int32_t)((((int64_t)(ARG1) * (ARG2)) + \
+                                                      ((int64_t)(ARG3) << 32U)     ) >> 32U))
+
+#endif /* ((defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+/*@} end of group CMSIS_SIMD_intrinsics */
+
+
+#endif /* __CMSIS_ARMCC_H */

Drivers/CMSIS/Core/Include/cmsis_compiler.h

@@ -0,0 +1,266 @@
+/**************************************************************************//**
+ * @file     cmsis_compiler.h
+ * @brief    CMSIS compiler generic header file
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef __CMSIS_COMPILER_H
+#define __CMSIS_COMPILER_H
+
+#include <stdint.h>
+
+/*
+ * Arm Compiler 4/5
+ */
+#if   defined ( __CC_ARM )
+  #include "cmsis_armcc.h"
+
+
+/*
+ * Arm Compiler 6 (armclang)
+ */
+#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)
+  #include "cmsis_armclang.h"
+
+
+/*
+ * GNU Compiler
+ */
+#elif defined ( __GNUC__ )
+  #include "cmsis_gcc.h"
+
+
+/*
+ * IAR Compiler
+ */
+#elif defined ( __ICCARM__ )
+  #include <cmsis_iccarm.h>
+
+
+/*
+ * TI Arm Compiler
+ */
+#elif defined ( __TI_ARM__ )
+  #include <cmsis_ccs.h>
+
+  #ifndef   __ASM
+    #define __ASM                                  __asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                               inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE                        static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE                   __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    #define __NO_RETURN                            __attribute__((noreturn))
+  #endif
+  #ifndef   __USED
+    #define __USED                                 __attribute__((used))
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                                 __attribute__((weak))
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                               __attribute__((packed))
+  #endif
+  #ifndef   __PACKED_STRUCT
+    #define __PACKED_STRUCT                        struct __attribute__((packed))
+  #endif
+  #ifndef   __PACKED_UNION
+    #define __PACKED_UNION                         union __attribute__((packed))
+  #endif
+  #ifndef   __UNALIGNED_UINT32        /* deprecated */
+    struct __attribute__((packed)) T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)                  (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT16_WRITE
+    __PACKED_STRUCT T_UINT16_WRITE { uint16_t v; };
+    #define __UNALIGNED_UINT16_WRITE(addr, val)    (void)((((struct T_UINT16_WRITE *)(void*)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT16_READ
+    __PACKED_STRUCT T_UINT16_READ { uint16_t v; };
+    #define __UNALIGNED_UINT16_READ(addr)          (((const struct T_UINT16_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT32_WRITE
+    __PACKED_STRUCT T_UINT32_WRITE { uint32_t v; };
+    #define __UNALIGNED_UINT32_WRITE(addr, val)    (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT32_READ
+    __PACKED_STRUCT T_UINT32_READ { uint32_t v; };
+    #define __UNALIGNED_UINT32_READ(addr)          (((const struct T_UINT32_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #define __ALIGNED(x)                           __attribute__((aligned(x)))
+  #endif
+  #ifndef   __RESTRICT
+    #warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored.
+    #define __RESTRICT
+  #endif
+
+
+/*
+ * TASKING Compiler
+ */
+#elif defined ( __TASKING__ )
+  /*
+   * The CMSIS functions have been implemented as intrinsics in the compiler.
+   * Please use "carm -?i" to get an up to date list of all intrinsics,
+   * Including the CMSIS ones.
+   */
+
+  #ifndef   __ASM
+    #define __ASM                                  __asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                               inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE                        static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE                   __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    #define __NO_RETURN                            __attribute__((noreturn))
+  #endif
+  #ifndef   __USED
+    #define __USED                                 __attribute__((used))
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                                 __attribute__((weak))
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                               __packed__
+  #endif
+  #ifndef   __PACKED_STRUCT
+    #define __PACKED_STRUCT                        struct __packed__
+  #endif
+  #ifndef   __PACKED_UNION
+    #define __PACKED_UNION                         union __packed__
+  #endif
+  #ifndef   __UNALIGNED_UINT32        /* deprecated */
+    struct __packed__ T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)                  (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT16_WRITE
+    __PACKED_STRUCT T_UINT16_WRITE { uint16_t v; };
+    #define __UNALIGNED_UINT16_WRITE(addr, val)    (void)((((struct T_UINT16_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT16_READ
+    __PACKED_STRUCT T_UINT16_READ { uint16_t v; };
+    #define __UNALIGNED_UINT16_READ(addr)          (((const struct T_UINT16_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT32_WRITE
+    __PACKED_STRUCT T_UINT32_WRITE { uint32_t v; };
+    #define __UNALIGNED_UINT32_WRITE(addr, val)    (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT32_READ
+    __PACKED_STRUCT T_UINT32_READ { uint32_t v; };
+    #define __UNALIGNED_UINT32_READ(addr)          (((const struct T_UINT32_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #define __ALIGNED(x)              __align(x)
+  #endif
+  #ifndef   __RESTRICT
+    #warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored.
+    #define __RESTRICT
+  #endif
+
+
+/*
+ * COSMIC Compiler
+ */
+#elif defined ( __CSMC__ )
+   #include <cmsis_csm.h>
+
+ #ifndef   __ASM
+    #define __ASM                                  _asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                               inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE                        static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE                   __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    // NO RETURN is automatically detected hence no warning here
+    #define __NO_RETURN
+  #endif
+  #ifndef   __USED
+    #warning No compiler specific solution for __USED. __USED is ignored.
+    #define __USED
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                                 __weak
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                               @packed
+  #endif
+  #ifndef   __PACKED_STRUCT
+    #define __PACKED_STRUCT                        @packed struct
+  #endif
+  #ifndef   __PACKED_UNION
+    #define __PACKED_UNION                         @packed union
+  #endif
+  #ifndef   __UNALIGNED_UINT32        /* deprecated */
+    @packed struct T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)                  (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT16_WRITE
+    __PACKED_STRUCT T_UINT16_WRITE { uint16_t v; };
+    #define __UNALIGNED_UINT16_WRITE(addr, val)    (void)((((struct T_UINT16_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT16_READ
+    __PACKED_STRUCT T_UINT16_READ { uint16_t v; };
+    #define __UNALIGNED_UINT16_READ(addr)          (((const struct T_UINT16_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT32_WRITE
+    __PACKED_STRUCT T_UINT32_WRITE { uint32_t v; };
+    #define __UNALIGNED_UINT32_WRITE(addr, val)    (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT32_READ
+    __PACKED_STRUCT T_UINT32_READ { uint32_t v; };
+    #define __UNALIGNED_UINT32_READ(addr)          (((const struct T_UINT32_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #warning No compiler specific solution for __ALIGNED. __ALIGNED is ignored.
+    #define __ALIGNED(x)
+  #endif
+  #ifndef   __RESTRICT
+    #warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored.
+    #define __RESTRICT
+  #endif
+
+
+#else
+  #error Unknown compiler.
+#endif
+
+
+#endif /* __CMSIS_COMPILER_H */
+

Drivers/CMSIS/Core/Include/cmsis_iccarm.h

@@ -0,0 +1,935 @@
+/**************************************************************************//**
+ * @file     cmsis_iccarm.h
+ * @brief    CMSIS compiler ICCARM (IAR Compiler for Arm) header file
+ * @version  V5.0.7
+ * @date     19. June 2018
+ ******************************************************************************/
+
+//------------------------------------------------------------------------------
+//
+// Copyright (c) 2017-2018 IAR Systems
+//
+// Licensed under the Apache License, Version 2.0 (the "License")
+// you may not use this file except in compliance with the License.
+// You may obtain a copy of the License at
+//     http://www.apache.org/licenses/LICENSE-2.0
+//
+// Unless required by applicable law or agreed to in writing, software
+// distributed under the License is distributed on an "AS IS" BASIS,
+// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+// See the License for the specific language governing permissions and
+// limitations under the License.
+//
+//------------------------------------------------------------------------------
+
+
+#ifndef __CMSIS_ICCARM_H__
+#define __CMSIS_ICCARM_H__
+
+#ifndef __ICCARM__
+  #error This file should only be compiled by ICCARM
+#endif
+
+#pragma system_include
+
+#define __IAR_FT _Pragma("inline=forced") __intrinsic
+
+#if (__VER__ >= 8000000)
+  #define __ICCARM_V8 1
+#else
+  #define __ICCARM_V8 0
+#endif
+
+#ifndef __ALIGNED
+  #if __ICCARM_V8
+    #define __ALIGNED(x) __attribute__((aligned(x)))
+  #elif (__VER__ >= 7080000)
+    /* Needs IAR language extensions */
+    #define __ALIGNED(x) __attribute__((aligned(x)))
+  #else
+    #warning No compiler specific solution for __ALIGNED.__ALIGNED is ignored.
+    #define __ALIGNED(x)
+  #endif
+#endif
+
+
+/* Define compiler macros for CPU architecture, used in CMSIS 5.
+ */
+#if __ARM_ARCH_6M__ || __ARM_ARCH_7M__ || __ARM_ARCH_7EM__ || __ARM_ARCH_8M_BASE__ || __ARM_ARCH_8M_MAIN__
+/* Macros already defined */
+#else
+  #if defined(__ARM8M_MAINLINE__) || defined(__ARM8EM_MAINLINE__)
+    #define __ARM_ARCH_8M_MAIN__ 1
+  #elif defined(__ARM8M_BASELINE__)
+    #define __ARM_ARCH_8M_BASE__ 1
+  #elif defined(__ARM_ARCH_PROFILE) && __ARM_ARCH_PROFILE == 'M'
+    #if __ARM_ARCH == 6
+      #define __ARM_ARCH_6M__ 1
+    #elif __ARM_ARCH == 7
+      #if __ARM_FEATURE_DSP
+        #define __ARM_ARCH_7EM__ 1
+      #else
+        #define __ARM_ARCH_7M__ 1
+      #endif
+    #endif /* __ARM_ARCH */
+  #endif /* __ARM_ARCH_PROFILE == 'M' */
+#endif
+
+/* Alternativ core deduction for older ICCARM's */
+#if !defined(__ARM_ARCH_6M__) && !defined(__ARM_ARCH_7M__) && !defined(__ARM_ARCH_7EM__) && \
+    !defined(__ARM_ARCH_8M_BASE__) && !defined(__ARM_ARCH_8M_MAIN__)
+  #if defined(__ARM6M__) && (__CORE__ == __ARM6M__)
+    #define __ARM_ARCH_6M__ 1
+  #elif defined(__ARM7M__) && (__CORE__ == __ARM7M__)
+    #define __ARM_ARCH_7M__ 1
+  #elif defined(__ARM7EM__) && (__CORE__ == __ARM7EM__)
+    #define __ARM_ARCH_7EM__  1
+  #elif defined(__ARM8M_BASELINE__) && (__CORE == __ARM8M_BASELINE__)
+    #define __ARM_ARCH_8M_BASE__ 1
+  #elif defined(__ARM8M_MAINLINE__) && (__CORE == __ARM8M_MAINLINE__)
+    #define __ARM_ARCH_8M_MAIN__ 1
+  #elif defined(__ARM8EM_MAINLINE__) && (__CORE == __ARM8EM_MAINLINE__)
+    #define __ARM_ARCH_8M_MAIN__ 1
+  #else
+    #error "Unknown target."
+  #endif
+#endif
+
+
+
+#if defined(__ARM_ARCH_6M__) && __ARM_ARCH_6M__==1
+  #define __IAR_M0_FAMILY  1
+#elif defined(__ARM_ARCH_8M_BASE__) && __ARM_ARCH_8M_BASE__==1
+  #define __IAR_M0_FAMILY  1
+#else
+  #define __IAR_M0_FAMILY  0
+#endif
+
+
+#ifndef __ASM
+  #define __ASM __asm
+#endif
+
+#ifndef __INLINE
+  #define __INLINE inline
+#endif
+
+#ifndef   __NO_RETURN
+  #if __ICCARM_V8
+    #define __NO_RETURN __attribute__((__noreturn__))
+  #else
+    #define __NO_RETURN _Pragma("object_attribute=__noreturn")
+  #endif
+#endif
+
+#ifndef   __PACKED
+  #if __ICCARM_V8
+    #define __PACKED __attribute__((packed, aligned(1)))
+  #else
+    /* Needs IAR language extensions */
+    #define __PACKED __packed
+  #endif
+#endif
+
+#ifndef   __PACKED_STRUCT
+  #if __ICCARM_V8
+    #define __PACKED_STRUCT struct __attribute__((packed, aligned(1)))
+  #else
+    /* Needs IAR language extensions */
+    #define __PACKED_STRUCT __packed struct
+  #endif
+#endif
+
+#ifndef   __PACKED_UNION
+  #if __ICCARM_V8
+    #define __PACKED_UNION union __attribute__((packed, aligned(1)))
+  #else
+    /* Needs IAR language extensions */
+    #define __PACKED_UNION __packed union
+  #endif
+#endif
+
+#ifndef   __RESTRICT
+  #define __RESTRICT            __restrict
+#endif
+
+#ifndef   __STATIC_INLINE
+  #define __STATIC_INLINE       static inline
+#endif
+
+#ifndef   __FORCEINLINE
+  #define __FORCEINLINE         _Pragma("inline=forced")
+#endif
+
+#ifndef   __STATIC_FORCEINLINE
+  #define __STATIC_FORCEINLINE  __FORCEINLINE __STATIC_INLINE
+#endif
+
+#ifndef __UNALIGNED_UINT16_READ
+#pragma language=save
+#pragma language=extended
+__IAR_FT uint16_t __iar_uint16_read(void const *ptr)
+{
+  return *(__packed uint16_t*)(ptr);
+}
+#pragma language=restore
+#define __UNALIGNED_UINT16_READ(PTR) __iar_uint16_read(PTR)
+#endif
+
+
+#ifndef __UNALIGNED_UINT16_WRITE
+#pragma language=save
+#pragma language=extended
+__IAR_FT void __iar_uint16_write(void const *ptr, uint16_t val)
+{
+  *(__packed uint16_t*)(ptr) = val;;
+}
+#pragma language=restore
+#define __UNALIGNED_UINT16_WRITE(PTR,VAL) __iar_uint16_write(PTR,VAL)
+#endif
+
+#ifndef __UNALIGNED_UINT32_READ
+#pragma language=save
+#pragma language=extended
+__IAR_FT uint32_t __iar_uint32_read(void const *ptr)
+{
+  return *(__packed uint32_t*)(ptr);
+}
+#pragma language=restore
+#define __UNALIGNED_UINT32_READ(PTR) __iar_uint32_read(PTR)
+#endif
+
+#ifndef __UNALIGNED_UINT32_WRITE
+#pragma language=save
+#pragma language=extended
+__IAR_FT void __iar_uint32_write(void const *ptr, uint32_t val)
+{
+  *(__packed uint32_t*)(ptr) = val;;
+}
+#pragma language=restore
+#define __UNALIGNED_UINT32_WRITE(PTR,VAL) __iar_uint32_write(PTR,VAL)
+#endif
+
+#ifndef __UNALIGNED_UINT32   /* deprecated */
+#pragma language=save
+#pragma language=extended
+__packed struct  __iar_u32 { uint32_t v; };
+#pragma language=restore
+#define __UNALIGNED_UINT32(PTR) (((struct __iar_u32 *)(PTR))->v)
+#endif
+
+#ifndef   __USED
+  #if __ICCARM_V8
+    #define __USED __attribute__((used))
+  #else
+    #define __USED _Pragma("__root")
+  #endif
+#endif
+
+#ifndef   __WEAK
+  #if __ICCARM_V8
+    #define __WEAK __attribute__((weak))
+  #else
+    #define __WEAK _Pragma("__weak")
+  #endif
+#endif
+
+
+#ifndef __ICCARM_INTRINSICS_VERSION__
+  #define __ICCARM_INTRINSICS_VERSION__  0
+#endif
+
+#if __ICCARM_INTRINSICS_VERSION__ == 2
+
+  #if defined(__CLZ)
+    #undef __CLZ
+  #endif
+  #if defined(__REVSH)
+    #undef __REVSH
+  #endif
+  #if defined(__RBIT)
+    #undef __RBIT
+  #endif
+  #if defined(__SSAT)
+    #undef __SSAT
+  #endif
+  #if defined(__USAT)
+    #undef __USAT
+  #endif
+
+  #include "iccarm_builtin.h"
+
+  #define __disable_fault_irq __iar_builtin_disable_fiq
+  #define __disable_irq       __iar_builtin_disable_interrupt
+  #define __enable_fault_irq  __iar_builtin_enable_fiq
+  #define __enable_irq        __iar_builtin_enable_interrupt
+  #define __arm_rsr           __iar_builtin_rsr
+  #define __arm_wsr           __iar_builtin_wsr
+
+
+  #define __get_APSR()                (__arm_rsr("APSR"))
+  #define __get_BASEPRI()             (__arm_rsr("BASEPRI"))
+  #define __get_CONTROL()             (__arm_rsr("CONTROL"))
+  #define __get_FAULTMASK()           (__arm_rsr("FAULTMASK"))
+
+  #if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+       (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+    #define __get_FPSCR()             (__arm_rsr("FPSCR"))
+    #define __set_FPSCR(VALUE)        (__arm_wsr("FPSCR", (VALUE)))
+  #else
+    #define __get_FPSCR()             ( 0 )
+    #define __set_FPSCR(VALUE)        ((void)VALUE)
+  #endif
+
+  #define __get_IPSR()                (__arm_rsr("IPSR"))
+  #define __get_MSP()                 (__arm_rsr("MSP"))
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure MSPLIM is RAZ/WI
+    #define __get_MSPLIM()            (0U)
+  #else
+    #define __get_MSPLIM()            (__arm_rsr("MSPLIM"))
+  #endif
+  #define __get_PRIMASK()             (__arm_rsr("PRIMASK"))
+  #define __get_PSP()                 (__arm_rsr("PSP"))
+
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure PSPLIM is RAZ/WI
+    #define __get_PSPLIM()            (0U)
+  #else
+    #define __get_PSPLIM()            (__arm_rsr("PSPLIM"))
+  #endif
+
+  #define __get_xPSR()                (__arm_rsr("xPSR"))
+
+  #define __set_BASEPRI(VALUE)        (__arm_wsr("BASEPRI", (VALUE)))
+  #define __set_BASEPRI_MAX(VALUE)    (__arm_wsr("BASEPRI_MAX", (VALUE)))
+  #define __set_CONTROL(VALUE)        (__arm_wsr("CONTROL", (VALUE)))
+  #define __set_FAULTMASK(VALUE)      (__arm_wsr("FAULTMASK", (VALUE)))
+  #define __set_MSP(VALUE)            (__arm_wsr("MSP", (VALUE)))
+
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure MSPLIM is RAZ/WI
+    #define __set_MSPLIM(VALUE)       ((void)(VALUE))
+  #else
+    #define __set_MSPLIM(VALUE)       (__arm_wsr("MSPLIM", (VALUE)))
+  #endif
+  #define __set_PRIMASK(VALUE)        (__arm_wsr("PRIMASK", (VALUE)))
+  #define __set_PSP(VALUE)            (__arm_wsr("PSP", (VALUE)))
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure PSPLIM is RAZ/WI
+    #define __set_PSPLIM(VALUE)       ((void)(VALUE))
+  #else
+    #define __set_PSPLIM(VALUE)       (__arm_wsr("PSPLIM", (VALUE)))
+  #endif
+
+  #define __TZ_get_CONTROL_NS()       (__arm_rsr("CONTROL_NS"))
+  #define __TZ_set_CONTROL_NS(VALUE)  (__arm_wsr("CONTROL_NS", (VALUE)))
+  #define __TZ_get_PSP_NS()           (__arm_rsr("PSP_NS"))
+  #define __TZ_set_PSP_NS(VALUE)      (__arm_wsr("PSP_NS", (VALUE)))
+  #define __TZ_get_MSP_NS()           (__arm_rsr("MSP_NS"))
+  #define __TZ_set_MSP_NS(VALUE)      (__arm_wsr("MSP_NS", (VALUE)))
+  #define __TZ_get_SP_NS()            (__arm_rsr("SP_NS"))
+  #define __TZ_set_SP_NS(VALUE)       (__arm_wsr("SP_NS", (VALUE)))
+  #define __TZ_get_PRIMASK_NS()       (__arm_rsr("PRIMASK_NS"))
+  #define __TZ_set_PRIMASK_NS(VALUE)  (__arm_wsr("PRIMASK_NS", (VALUE)))
+  #define __TZ_get_BASEPRI_NS()       (__arm_rsr("BASEPRI_NS"))
+  #define __TZ_set_BASEPRI_NS(VALUE)  (__arm_wsr("BASEPRI_NS", (VALUE)))
+  #define __TZ_get_FAULTMASK_NS()     (__arm_rsr("FAULTMASK_NS"))
+  #define __TZ_set_FAULTMASK_NS(VALUE)(__arm_wsr("FAULTMASK_NS", (VALUE)))
+
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure PSPLIM is RAZ/WI
+    #define __TZ_get_PSPLIM_NS()      (0U)
+    #define __TZ_set_PSPLIM_NS(VALUE) ((void)(VALUE))
+  #else
+    #define __TZ_get_PSPLIM_NS()      (__arm_rsr("PSPLIM_NS"))
+    #define __TZ_set_PSPLIM_NS(VALUE) (__arm_wsr("PSPLIM_NS", (VALUE)))
+  #endif
+
+  #define __TZ_get_MSPLIM_NS()        (__arm_rsr("MSPLIM_NS"))
+  #define __TZ_set_MSPLIM_NS(VALUE)   (__arm_wsr("MSPLIM_NS", (VALUE)))
+
+  #define __NOP     __iar_builtin_no_operation
+
+  #define __CLZ     __iar_builtin_CLZ
+  #define __CLREX   __iar_builtin_CLREX
+
+  #define __DMB     __iar_builtin_DMB
+  #define __DSB     __iar_builtin_DSB
+  #define __ISB     __iar_builtin_ISB
+
+  #define __LDREXB  __iar_builtin_LDREXB
+  #define __LDREXH  __iar_builtin_LDREXH
+  #define __LDREXW  __iar_builtin_LDREX
+
+  #define __RBIT    __iar_builtin_RBIT
+  #define __REV     __iar_builtin_REV
+  #define __REV16   __iar_builtin_REV16
+
+  __IAR_FT int16_t __REVSH(int16_t val)
+  {
+    return (int16_t) __iar_builtin_REVSH(val);
+  }
+
+  #define __ROR     __iar_builtin_ROR
+  #define __RRX     __iar_builtin_RRX
+
+  #define __SEV     __iar_builtin_SEV
+
+  #if !__IAR_M0_FAMILY
+    #define __SSAT    __iar_builtin_SSAT
+  #endif
+
+  #define __STREXB  __iar_builtin_STREXB
+  #define __STREXH  __iar_builtin_STREXH
+  #define __STREXW  __iar_builtin_STREX
+
+  #if !__IAR_M0_FAMILY
+    #define __USAT    __iar_builtin_USAT
+  #endif
+
+  #define __WFE     __iar_builtin_WFE
+  #define __WFI     __iar_builtin_WFI
+
+  #if __ARM_MEDIA__
+    #define __SADD8   __iar_builtin_SADD8
+    #define __QADD8   __iar_builtin_QADD8
+    #define __SHADD8  __iar_builtin_SHADD8
+    #define __UADD8   __iar_builtin_UADD8
+    #define __UQADD8  __iar_builtin_UQADD8
+    #define __UHADD8  __iar_builtin_UHADD8
+    #define __SSUB8   __iar_builtin_SSUB8
+    #define __QSUB8   __iar_builtin_QSUB8
+    #define __SHSUB8  __iar_builtin_SHSUB8
+    #define __USUB8   __iar_builtin_USUB8
+    #define __UQSUB8  __iar_builtin_UQSUB8
+    #define __UHSUB8  __iar_builtin_UHSUB8
+    #define __SADD16  __iar_builtin_SADD16
+    #define __QADD16  __iar_builtin_QADD16
+    #define __SHADD16 __iar_builtin_SHADD16
+    #define __UADD16  __iar_builtin_UADD16
+    #define __UQADD16 __iar_builtin_UQADD16
+    #define __UHADD16 __iar_builtin_UHADD16
+    #define __SSUB16  __iar_builtin_SSUB16
+    #define __QSUB16  __iar_builtin_QSUB16
+    #define __SHSUB16 __iar_builtin_SHSUB16
+    #define __USUB16  __iar_builtin_USUB16
+    #define __UQSUB16 __iar_builtin_UQSUB16
+    #define __UHSUB16 __iar_builtin_UHSUB16
+    #define __SASX    __iar_builtin_SASX
+    #define __QASX    __iar_builtin_QASX
+    #define __SHASX   __iar_builtin_SHASX
+    #define __UASX    __iar_builtin_UASX
+    #define __UQASX   __iar_builtin_UQASX
+    #define __UHASX   __iar_builtin_UHASX
+    #define __SSAX    __iar_builtin_SSAX
+    #define __QSAX    __iar_builtin_QSAX
+    #define __SHSAX   __iar_builtin_SHSAX
+    #define __USAX    __iar_builtin_USAX
+    #define __UQSAX   __iar_builtin_UQSAX
+    #define __UHSAX   __iar_builtin_UHSAX
+    #define __USAD8   __iar_builtin_USAD8
+    #define __USADA8  __iar_builtin_USADA8
+    #define __SSAT16  __iar_builtin_SSAT16
+    #define __USAT16  __iar_builtin_USAT16
+    #define __UXTB16  __iar_builtin_UXTB16
+    #define __UXTAB16 __iar_builtin_UXTAB16
+    #define __SXTB16  __iar_builtin_SXTB16
+    #define __SXTAB16 __iar_builtin_SXTAB16
+    #define __SMUAD   __iar_builtin_SMUAD
+    #define __SMUADX  __iar_builtin_SMUADX
+    #define __SMMLA   __iar_builtin_SMMLA
+    #define __SMLAD   __iar_builtin_SMLAD
+    #define __SMLADX  __iar_builtin_SMLADX
+    #define __SMLALD  __iar_builtin_SMLALD
+    #define __SMLALDX __iar_builtin_SMLALDX
+    #define __SMUSD   __iar_builtin_SMUSD
+    #define __SMUSDX  __iar_builtin_SMUSDX
+    #define __SMLSD   __iar_builtin_SMLSD
+    #define __SMLSDX  __iar_builtin_SMLSDX
+    #define __SMLSLD  __iar_builtin_SMLSLD
+    #define __SMLSLDX __iar_builtin_SMLSLDX
+    #define __SEL     __iar_builtin_SEL
+    #define __QADD    __iar_builtin_QADD
+    #define __QSUB    __iar_builtin_QSUB
+    #define __PKHBT   __iar_builtin_PKHBT
+    #define __PKHTB   __iar_builtin_PKHTB
+  #endif
+
+#else /* __ICCARM_INTRINSICS_VERSION__ == 2 */
+
+  #if __IAR_M0_FAMILY
+   /* Avoid clash between intrinsics.h and arm_math.h when compiling for Cortex-M0. */
+    #define __CLZ  __cmsis_iar_clz_not_active
+    #define __SSAT __cmsis_iar_ssat_not_active
+    #define __USAT __cmsis_iar_usat_not_active
+    #define __RBIT __cmsis_iar_rbit_not_active
+    #define __get_APSR  __cmsis_iar_get_APSR_not_active
+  #endif
+
+
+  #if (!((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+         (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     ))
+    #define __get_FPSCR __cmsis_iar_get_FPSR_not_active
+    #define __set_FPSCR __cmsis_iar_set_FPSR_not_active
+  #endif
+
+  #ifdef __INTRINSICS_INCLUDED
+  #error intrinsics.h is already included previously!
+  #endif
+
+  #include <intrinsics.h>
+
+  #if __IAR_M0_FAMILY
+   /* Avoid clash between intrinsics.h and arm_math.h when compiling for Cortex-M0. */
+    #undef __CLZ
+    #undef __SSAT
+    #undef __USAT
+    #undef __RBIT
+    #undef __get_APSR
+
+    __STATIC_INLINE uint8_t __CLZ(uint32_t data)
+    {
+      if (data == 0U) { return 32U; }
+
+      uint32_t count = 0U;
+      uint32_t mask = 0x80000000U;
+
+      while ((data & mask) == 0U)
+      {
+        count += 1U;
+        mask = mask >> 1U;
+      }
+      return count;
+    }
+
+    __STATIC_INLINE uint32_t __RBIT(uint32_t v)
+    {
+      uint8_t sc = 31U;
+      uint32_t r = v;
+      for (v >>= 1U; v; v >>= 1U)
+      {
+        r <<= 1U;
+        r |= v & 1U;
+        sc--;
+      }
+      return (r << sc);
+    }
+
+    __STATIC_INLINE  uint32_t __get_APSR(void)
+    {
+      uint32_t res;
+      __asm("MRS      %0,APSR" : "=r" (res));
+      return res;
+    }
+
+  #endif
+
+  #if (!((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+         (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     ))
+    #undef __get_FPSCR
+    #undef __set_FPSCR
+    #define __get_FPSCR()       (0)
+    #define __set_FPSCR(VALUE)  ((void)VALUE)
+  #endif
+
+  #pragma diag_suppress=Pe940
+  #pragma diag_suppress=Pe177
+
+  #define __enable_irq    __enable_interrupt
+  #define __disable_irq   __disable_interrupt
+  #define __NOP           __no_operation
+
+  #define __get_xPSR      __get_PSR
+
+  #if (!defined(__ARM_ARCH_6M__) || __ARM_ARCH_6M__==0)
+
+    __IAR_FT uint32_t __LDREXW(uint32_t volatile *ptr)
+    {
+      return __LDREX((unsigned long *)ptr);
+    }
+
+    __IAR_FT uint32_t __STREXW(uint32_t value, uint32_t volatile *ptr)
+    {
+      return __STREX(value, (unsigned long *)ptr);
+    }
+  #endif
+
+
+  /* __CORTEX_M is defined in core_cm0.h, core_cm3.h and core_cm4.h. */
+  #if (__CORTEX_M >= 0x03)
+
+    __IAR_FT uint32_t __RRX(uint32_t value)
+    {
+      uint32_t result;
+      __ASM("RRX      %0, %1" : "=r"(result) : "r" (value) : "cc");
+      return(result);
+    }
+
+    __IAR_FT void __set_BASEPRI_MAX(uint32_t value)
+    {
+      __asm volatile("MSR      BASEPRI_MAX,%0"::"r" (value));
+    }
+
+
+    #define __enable_fault_irq  __enable_fiq
+    #define __disable_fault_irq __disable_fiq
+
+
+  #endif /* (__CORTEX_M >= 0x03) */
+
+  __IAR_FT uint32_t __ROR(uint32_t op1, uint32_t op2)
+  {
+    return (op1 >> op2) | (op1 << ((sizeof(op1)*8)-op2));
+  }
+
+  #if ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \
+       (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1))    )
+
+   __IAR_FT uint32_t __get_MSPLIM(void)
+    {
+      uint32_t res;
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure MSPLIM is RAZ/WI
+      res = 0U;
+    #else
+      __asm volatile("MRS      %0,MSPLIM" : "=r" (res));
+    #endif
+      return res;
+    }
+
+    __IAR_FT void   __set_MSPLIM(uint32_t value)
+    {
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure MSPLIM is RAZ/WI
+      (void)value;
+    #else
+      __asm volatile("MSR      MSPLIM,%0" :: "r" (value));
+    #endif
+    }
+
+    __IAR_FT uint32_t __get_PSPLIM(void)
+    {
+      uint32_t res;
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      res = 0U;
+    #else
+      __asm volatile("MRS      %0,PSPLIM" : "=r" (res));
+    #endif
+      return res;
+    }
+
+    __IAR_FT void   __set_PSPLIM(uint32_t value)
+    {
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      (void)value;
+    #else
+      __asm volatile("MSR      PSPLIM,%0" :: "r" (value));
+    #endif
+    }
+
+    __IAR_FT uint32_t __TZ_get_CONTROL_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,CONTROL_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_CONTROL_NS(uint32_t value)
+    {
+      __asm volatile("MSR      CONTROL_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_PSP_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,PSP_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_PSP_NS(uint32_t value)
+    {
+      __asm volatile("MSR      PSP_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_MSP_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,MSP_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_MSP_NS(uint32_t value)
+    {
+      __asm volatile("MSR      MSP_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_SP_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,SP_NS" : "=r" (res));
+      return res;
+    }
+    __IAR_FT void   __TZ_set_SP_NS(uint32_t value)
+    {
+      __asm volatile("MSR      SP_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_PRIMASK_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,PRIMASK_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_PRIMASK_NS(uint32_t value)
+    {
+      __asm volatile("MSR      PRIMASK_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_BASEPRI_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,BASEPRI_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_BASEPRI_NS(uint32_t value)
+    {
+      __asm volatile("MSR      BASEPRI_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_FAULTMASK_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,FAULTMASK_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_FAULTMASK_NS(uint32_t value)
+    {
+      __asm volatile("MSR      FAULTMASK_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_PSPLIM_NS(void)
+    {
+      uint32_t res;
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      res = 0U;
+    #else
+      __asm volatile("MRS      %0,PSPLIM_NS" : "=r" (res));
+    #endif
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_PSPLIM_NS(uint32_t value)
+    {
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      (void)value;
+    #else
+      __asm volatile("MSR      PSPLIM_NS,%0" :: "r" (value));
+    #endif
+    }
+
+    __IAR_FT uint32_t   __TZ_get_MSPLIM_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,MSPLIM_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_MSPLIM_NS(uint32_t value)
+    {
+      __asm volatile("MSR      MSPLIM_NS,%0" :: "r" (value));
+    }
+
+  #endif /* __ARM_ARCH_8M_MAIN__ or __ARM_ARCH_8M_BASE__ */
+
+#endif   /* __ICCARM_INTRINSICS_VERSION__ == 2 */
+
+#define __BKPT(value)    __asm volatile ("BKPT     %0" : : "i"(value))
+
+#if __IAR_M0_FAMILY
+  __STATIC_INLINE int32_t __SSAT(int32_t val, uint32_t sat)
+  {
+    if ((sat >= 1U) && (sat <= 32U))
+    {
+      const int32_t max = (int32_t)((1U << (sat - 1U)) - 1U);
+      const int32_t min = -1 - max ;
+      if (val > max)
+      {
+        return max;
+      }
+      else if (val < min)
+      {
+        return min;
+      }
+    }
+    return val;
+  }
+
+  __STATIC_INLINE uint32_t __USAT(int32_t val, uint32_t sat)
+  {
+    if (sat <= 31U)
+    {
+      const uint32_t max = ((1U << sat) - 1U);
+      if (val > (int32_t)max)
+      {
+        return max;
+      }
+      else if (val < 0)
+      {
+        return 0U;
+      }
+    }
+    return (uint32_t)val;
+  }
+#endif
+
+#if (__CORTEX_M >= 0x03)   /* __CORTEX_M is defined in core_cm0.h, core_cm3.h and core_cm4.h. */
+
+  __IAR_FT uint8_t __LDRBT(volatile uint8_t *addr)
+  {
+    uint32_t res;
+    __ASM("LDRBT %0, [%1]" : "=r" (res) : "r" (addr) : "memory");
+    return ((uint8_t)res);
+  }
+
+  __IAR_FT uint16_t __LDRHT(volatile uint16_t *addr)
+  {
+    uint32_t res;
+    __ASM("LDRHT %0, [%1]" : "=r" (res) : "r" (addr) : "memory");
+    return ((uint16_t)res);
+  }
+
+  __IAR_FT uint32_t __LDRT(volatile uint32_t *addr)
+  {
+    uint32_t res;
+    __ASM("LDRT %0, [%1]" : "=r" (res) : "r" (addr) : "memory");
+    return res;
+  }
+
+  __IAR_FT void __STRBT(uint8_t value, volatile uint8_t *addr)
+  {
+    __ASM("STRBT %1, [%0]" : : "r" (addr), "r" ((uint32_t)value) : "memory");
+  }
+
+  __IAR_FT void __STRHT(uint16_t value, volatile uint16_t *addr)
+  {
+    __ASM("STRHT %1, [%0]" : : "r" (addr), "r" ((uint32_t)value) : "memory");
+  }
+
+  __IAR_FT void __STRT(uint32_t value, volatile uint32_t *addr)
+  {
+    __ASM("STRT %1, [%0]" : : "r" (addr), "r" (value) : "memory");
+  }
+
+#endif /* (__CORTEX_M >= 0x03) */
+
+#if ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \
+     (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1))    )
+
+
+  __IAR_FT uint8_t __LDAB(volatile uint8_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAB %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint8_t)res);
+  }
+
+  __IAR_FT uint16_t __LDAH(volatile uint16_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAH %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint16_t)res);
+  }
+
+  __IAR_FT uint32_t __LDA(volatile uint32_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDA %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return res;
+  }
+
+  __IAR_FT void __STLB(uint8_t value, volatile uint8_t *ptr)
+  {
+    __ASM volatile ("STLB %1, [%0]" :: "r" (ptr), "r" (value) : "memory");
+  }
+
+  __IAR_FT void __STLH(uint16_t value, volatile uint16_t *ptr)
+  {
+    __ASM volatile ("STLH %1, [%0]" :: "r" (ptr), "r" (value) : "memory");
+  }
+
+  __IAR_FT void __STL(uint32_t value, volatile uint32_t *ptr)
+  {
+    __ASM volatile ("STL %1, [%0]" :: "r" (ptr), "r" (value) : "memory");
+  }
+
+  __IAR_FT uint8_t __LDAEXB(volatile uint8_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAEXB %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint8_t)res);
+  }
+
+  __IAR_FT uint16_t __LDAEXH(volatile uint16_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAEXH %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint16_t)res);
+  }
+
+  __IAR_FT uint32_t __LDAEX(volatile uint32_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAEX %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return res;
+  }
+
+  __IAR_FT uint32_t __STLEXB(uint8_t value, volatile uint8_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("STLEXB %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory");
+    return res;
+  }
+
+  __IAR_FT uint32_t __STLEXH(uint16_t value, volatile uint16_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("STLEXH %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory");
+    return res;
+  }
+
+  __IAR_FT uint32_t __STLEX(uint32_t value, volatile uint32_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("STLEX %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory");
+    return res;
+  }
+
+#endif /* __ARM_ARCH_8M_MAIN__ or __ARM_ARCH_8M_BASE__ */
+
+#undef __IAR_FT
+#undef __IAR_M0_FAMILY
+#undef __ICCARM_V8
+
+#pragma diag_default=Pe940
+#pragma diag_default=Pe177
+
+#endif /* __CMSIS_ICCARM_H__ */

Drivers/CMSIS/Core/Include/cmsis_version.h

@@ -0,0 +1,39 @@
+/**************************************************************************//**
+ * @file     cmsis_version.h
+ * @brief    CMSIS Core(M) Version definitions
+ * @version  V5.0.2
+ * @date     19. April 2017
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2017 ARM Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef __CMSIS_VERSION_H
+#define __CMSIS_VERSION_H
+
+/*  CMSIS Version definitions */
+#define __CM_CMSIS_VERSION_MAIN  ( 5U)                                      /*!< [31:16] CMSIS Core(M) main version */
+#define __CM_CMSIS_VERSION_SUB   ( 1U)                                      /*!< [15:0]  CMSIS Core(M) sub version */
+#define __CM_CMSIS_VERSION       ((__CM_CMSIS_VERSION_MAIN << 16U) | \
+                                   __CM_CMSIS_VERSION_SUB           )       /*!< CMSIS Core(M) version number */
+#endif

Drivers/CMSIS/Core/Include/core_cm0.h

@@ -0,0 +1,949 @@
+/**************************************************************************//**
+ * @file     core_cm0.h
+ * @brief    CMSIS Cortex-M0 Core Peripheral Access Layer Header File
+ * @version  V5.0.5
+ * @date     28. May 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef __CORE_CM0_H_GENERIC
+#define __CORE_CM0_H_GENERIC
+
+#include <stdint.h>
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/**
+  \page CMSIS_MISRA_Exceptions  MISRA-C:2004 Compliance Exceptions
+  CMSIS violates the following MISRA-C:2004 rules:
+
+   \li Required Rule 8.5, object/function definition in header file.<br>
+     Function definitions in header files are used to allow 'inlining'.
+
+   \li Required Rule 18.4, declaration of union type or object of union type: '{...}'.<br>
+     Unions are used for effective representation of core registers.
+
+   \li Advisory Rule 19.7, Function-like macro defined.<br>
+     Function-like macros are used to allow more efficient code.
+ */
+
+
+/*******************************************************************************
+ *                 CMSIS definitions
+ ******************************************************************************/
+/**
+  \ingroup Cortex_M0
+  @{
+ */
+
+#include "cmsis_version.h"
+ 
+/*  CMSIS CM0 definitions */
+#define __CM0_CMSIS_VERSION_MAIN  (__CM_CMSIS_VERSION_MAIN)              /*!< \deprecated [31:16] CMSIS HAL main version */
+#define __CM0_CMSIS_VERSION_SUB   (__CM_CMSIS_VERSION_SUB)               /*!< \deprecated [15:0]  CMSIS HAL sub version */
+#define __CM0_CMSIS_VERSION       ((__CM0_CMSIS_VERSION_MAIN << 16U) | \
+                                    __CM0_CMSIS_VERSION_SUB           )  /*!< \deprecated CMSIS HAL version number */
+
+#define __CORTEX_M                (0U)                                   /*!< Cortex-M Core */
+
+/** __FPU_USED indicates whether an FPU is used or not.
+    This core does not support an FPU at all
+*/
+#define __FPU_USED       0U
+
+#if defined ( __CC_ARM )
+  #if defined __TARGET_FPU_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)
+  #if defined __ARM_PCS_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __GNUC__ )
+  #if defined (__VFP_FP__) && !defined(__SOFTFP__)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __ICCARM__ )
+  #if defined __ARMVFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TI_ARM__ )
+  #if defined __TI_VFP_SUPPORT__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TASKING__ )
+  #if defined __FPU_VFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __CSMC__ )
+  #if ( __CSMC__ & 0x400U)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#endif
+
+#include "cmsis_compiler.h"               /* CMSIS compiler specific defines */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM0_H_GENERIC */
+
+#ifndef __CMSIS_GENERIC
+
+#ifndef __CORE_CM0_H_DEPENDANT
+#define __CORE_CM0_H_DEPENDANT
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* check device defines and use defaults */
+#if defined __CHECK_DEVICE_DEFINES
+  #ifndef __CM0_REV
+    #define __CM0_REV               0x0000U
+    #warning "__CM0_REV not defined in device header file; using default!"
+  #endif
+
+  #ifndef __NVIC_PRIO_BITS
+    #define __NVIC_PRIO_BITS          2U
+    #warning "__NVIC_PRIO_BITS not defined in device header file; using default!"
+  #endif
+
+  #ifndef __Vendor_SysTickConfig
+    #define __Vendor_SysTickConfig    0U
+    #warning "__Vendor_SysTickConfig not defined in device header file; using default!"
+  #endif
+#endif
+
+/* IO definitions (access restrictions to peripheral registers) */
+/**
+    \defgroup CMSIS_glob_defs CMSIS Global Defines
+
+    <strong>IO Type Qualifiers</strong> are used
+    \li to specify the access to peripheral variables.
+    \li for automatic generation of peripheral register debug information.
+*/
+#ifdef __cplusplus
+  #define   __I     volatile             /*!< Defines 'read only' permissions */
+#else
+  #define   __I     volatile const       /*!< Defines 'read only' permissions */
+#endif
+#define     __O     volatile             /*!< Defines 'write only' permissions */
+#define     __IO    volatile             /*!< Defines 'read / write' permissions */
+
+/* following defines should be used for structure members */
+#define     __IM     volatile const      /*! Defines 'read only' structure member permissions */
+#define     __OM     volatile            /*! Defines 'write only' structure member permissions */
+#define     __IOM    volatile            /*! Defines 'read / write' structure member permissions */
+
+/*@} end of group Cortex_M0 */
+
+
+
+/*******************************************************************************
+ *                 Register Abstraction
+  Core Register contain:
+  - Core Register
+  - Core NVIC Register
+  - Core SCB Register
+  - Core SysTick Register
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_core_register Defines and Type Definitions
+  \brief Type definitions and defines for Cortex-M processor based devices.
+*/
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_CORE  Status and Control Registers
+  \brief      Core Register type definitions.
+  @{
+ */
+
+/**
+  \brief  Union type to access the Application Program Status Register (APSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:28;              /*!< bit:  0..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} APSR_Type;
+
+/* APSR Register Definitions */
+#define APSR_N_Pos                         31U                                            /*!< APSR: N Position */
+#define APSR_N_Msk                         (1UL << APSR_N_Pos)                            /*!< APSR: N Mask */
+
+#define APSR_Z_Pos                         30U                                            /*!< APSR: Z Position */
+#define APSR_Z_Msk                         (1UL << APSR_Z_Pos)                            /*!< APSR: Z Mask */
+
+#define APSR_C_Pos                         29U                                            /*!< APSR: C Position */
+#define APSR_C_Msk                         (1UL << APSR_C_Pos)                            /*!< APSR: C Mask */
+
+#define APSR_V_Pos                         28U                                            /*!< APSR: V Position */
+#define APSR_V_Msk                         (1UL << APSR_V_Pos)                            /*!< APSR: V Mask */
+
+
+/**
+  \brief  Union type to access the Interrupt Program Status Register (IPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:23;              /*!< bit:  9..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} IPSR_Type;
+
+/* IPSR Register Definitions */
+#define IPSR_ISR_Pos                        0U                                            /*!< IPSR: ISR Position */
+#define IPSR_ISR_Msk                       (0x1FFUL /*<< IPSR_ISR_Pos*/)                  /*!< IPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Special-Purpose Program Status Registers (xPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:15;              /*!< bit:  9..23  Reserved */
+    uint32_t T:1;                        /*!< bit:     24  Thumb bit        (read 0) */
+    uint32_t _reserved1:3;               /*!< bit: 25..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} xPSR_Type;
+
+/* xPSR Register Definitions */
+#define xPSR_N_Pos                         31U                                            /*!< xPSR: N Position */
+#define xPSR_N_Msk                         (1UL << xPSR_N_Pos)                            /*!< xPSR: N Mask */
+
+#define xPSR_Z_Pos                         30U                                            /*!< xPSR: Z Position */
+#define xPSR_Z_Msk                         (1UL << xPSR_Z_Pos)                            /*!< xPSR: Z Mask */
+
+#define xPSR_C_Pos                         29U                                            /*!< xPSR: C Position */
+#define xPSR_C_Msk                         (1UL << xPSR_C_Pos)                            /*!< xPSR: C Mask */
+
+#define xPSR_V_Pos                         28U                                            /*!< xPSR: V Position */
+#define xPSR_V_Msk                         (1UL << xPSR_V_Pos)                            /*!< xPSR: V Mask */
+
+#define xPSR_T_Pos                         24U                                            /*!< xPSR: T Position */
+#define xPSR_T_Msk                         (1UL << xPSR_T_Pos)                            /*!< xPSR: T Mask */
+
+#define xPSR_ISR_Pos                        0U                                            /*!< xPSR: ISR Position */
+#define xPSR_ISR_Msk                       (0x1FFUL /*<< xPSR_ISR_Pos*/)                  /*!< xPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Control Registers (CONTROL).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:1;               /*!< bit:      0  Reserved */
+    uint32_t SPSEL:1;                    /*!< bit:      1  Stack to be used */
+    uint32_t _reserved1:30;              /*!< bit:  2..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} CONTROL_Type;
+
+/* CONTROL Register Definitions */
+#define CONTROL_SPSEL_Pos                   1U                                            /*!< CONTROL: SPSEL Position */
+#define CONTROL_SPSEL_Msk                  (1UL << CONTROL_SPSEL_Pos)                     /*!< CONTROL: SPSEL Mask */
+
+/*@} end of group CMSIS_CORE */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_NVIC  Nested Vectored Interrupt Controller (NVIC)
+  \brief      Type definitions for the NVIC Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the Nested Vectored Interrupt Controller (NVIC).
+ */
+typedef struct
+{
+  __IOM uint32_t ISER[1U];               /*!< Offset: 0x000 (R/W)  Interrupt Set Enable Register */
+        uint32_t RESERVED0[31U];
+  __IOM uint32_t ICER[1U];               /*!< Offset: 0x080 (R/W)  Interrupt Clear Enable Register */
+        uint32_t RSERVED1[31U];
+  __IOM uint32_t ISPR[1U];               /*!< Offset: 0x100 (R/W)  Interrupt Set Pending Register */
+        uint32_t RESERVED2[31U];
+  __IOM uint32_t ICPR[1U];               /*!< Offset: 0x180 (R/W)  Interrupt Clear Pending Register */
+        uint32_t RESERVED3[31U];
+        uint32_t RESERVED4[64U];
+  __IOM uint32_t IP[8U];                 /*!< Offset: 0x300 (R/W)  Interrupt Priority Register */
+}  NVIC_Type;
+
+/*@} end of group CMSIS_NVIC */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SCB     System Control Block (SCB)
+  \brief    Type definitions for the System Control Block Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Control Block (SCB).
+ */
+typedef struct
+{
+  __IM  uint32_t CPUID;                  /*!< Offset: 0x000 (R/ )  CPUID Base Register */
+  __IOM uint32_t ICSR;                   /*!< Offset: 0x004 (R/W)  Interrupt Control and State Register */
+        uint32_t RESERVED0;
+  __IOM uint32_t AIRCR;                  /*!< Offset: 0x00C (R/W)  Application Interrupt and Reset Control Register */
+  __IOM uint32_t SCR;                    /*!< Offset: 0x010 (R/W)  System Control Register */
+  __IOM uint32_t CCR;                    /*!< Offset: 0x014 (R/W)  Configuration Control Register */
+        uint32_t RESERVED1;
+  __IOM uint32_t SHP[2U];                /*!< Offset: 0x01C (R/W)  System Handlers Priority Registers. [0] is RESERVED */
+  __IOM uint32_t SHCSR;                  /*!< Offset: 0x024 (R/W)  System Handler Control and State Register */
+} SCB_Type;
+
+/* SCB CPUID Register Definitions */
+#define SCB_CPUID_IMPLEMENTER_Pos          24U                                            /*!< SCB CPUID: IMPLEMENTER Position */
+#define SCB_CPUID_IMPLEMENTER_Msk          (0xFFUL << SCB_CPUID_IMPLEMENTER_Pos)          /*!< SCB CPUID: IMPLEMENTER Mask */
+
+#define SCB_CPUID_VARIANT_Pos              20U                                            /*!< SCB CPUID: VARIANT Position */
+#define SCB_CPUID_VARIANT_Msk              (0xFUL << SCB_CPUID_VARIANT_Pos)               /*!< SCB CPUID: VARIANT Mask */
+
+#define SCB_CPUID_ARCHITECTURE_Pos         16U                                            /*!< SCB CPUID: ARCHITECTURE Position */
+#define SCB_CPUID_ARCHITECTURE_Msk         (0xFUL << SCB_CPUID_ARCHITECTURE_Pos)          /*!< SCB CPUID: ARCHITECTURE Mask */
+
+#define SCB_CPUID_PARTNO_Pos                4U                                            /*!< SCB CPUID: PARTNO Position */
+#define SCB_CPUID_PARTNO_Msk               (0xFFFUL << SCB_CPUID_PARTNO_Pos)              /*!< SCB CPUID: PARTNO Mask */
+
+#define SCB_CPUID_REVISION_Pos              0U                                            /*!< SCB CPUID: REVISION Position */
+#define SCB_CPUID_REVISION_Msk             (0xFUL /*<< SCB_CPUID_REVISION_Pos*/)          /*!< SCB CPUID: REVISION Mask */
+
+/* SCB Interrupt Control State Register Definitions */
+#define SCB_ICSR_NMIPENDSET_Pos            31U                                            /*!< SCB ICSR: NMIPENDSET Position */
+#define SCB_ICSR_NMIPENDSET_Msk            (1UL << SCB_ICSR_NMIPENDSET_Pos)               /*!< SCB ICSR: NMIPENDSET Mask */
+
+#define SCB_ICSR_PENDSVSET_Pos             28U                                            /*!< SCB ICSR: PENDSVSET Position */
+#define SCB_ICSR_PENDSVSET_Msk             (1UL << SCB_ICSR_PENDSVSET_Pos)                /*!< SCB ICSR: PENDSVSET Mask */
+
+#define SCB_ICSR_PENDSVCLR_Pos             27U                                            /*!< SCB ICSR: PENDSVCLR Position */
+#define SCB_ICSR_PENDSVCLR_Msk             (1UL << SCB_ICSR_PENDSVCLR_Pos)                /*!< SCB ICSR: PENDSVCLR Mask */
+
+#define SCB_ICSR_PENDSTSET_Pos             26U                                            /*!< SCB ICSR: PENDSTSET Position */
+#define SCB_ICSR_PENDSTSET_Msk             (1UL << SCB_ICSR_PENDSTSET_Pos)                /*!< SCB ICSR: PENDSTSET Mask */
+
+#define SCB_ICSR_PENDSTCLR_Pos             25U                                            /*!< SCB ICSR: PENDSTCLR Position */
+#define SCB_ICSR_PENDSTCLR_Msk             (1UL << SCB_ICSR_PENDSTCLR_Pos)                /*!< SCB ICSR: PENDSTCLR Mask */
+
+#define SCB_ICSR_ISRPREEMPT_Pos            23U                                            /*!< SCB ICSR: ISRPREEMPT Position */
+#define SCB_ICSR_ISRPREEMPT_Msk            (1UL << SCB_ICSR_ISRPREEMPT_Pos)               /*!< SCB ICSR: ISRPREEMPT Mask */
+
+#define SCB_ICSR_ISRPENDING_Pos            22U                                            /*!< SCB ICSR: ISRPENDING Position */
+#define SCB_ICSR_ISRPENDING_Msk            (1UL << SCB_ICSR_ISRPENDING_Pos)               /*!< SCB ICSR: ISRPENDING Mask */
+
+#define SCB_ICSR_VECTPENDING_Pos           12U                                            /*!< SCB ICSR: VECTPENDING Position */
+#define SCB_ICSR_VECTPENDING_Msk           (0x1FFUL << SCB_ICSR_VECTPENDING_Pos)          /*!< SCB ICSR: VECTPENDING Mask */
+
+#define SCB_ICSR_VECTACTIVE_Pos             0U                                            /*!< SCB ICSR: VECTACTIVE Position */
+#define SCB_ICSR_VECTACTIVE_Msk            (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/)       /*!< SCB ICSR: VECTACTIVE Mask */
+
+/* SCB Application Interrupt and Reset Control Register Definitions */
+#define SCB_AIRCR_VECTKEY_Pos              16U                                            /*!< SCB AIRCR: VECTKEY Position */
+#define SCB_AIRCR_VECTKEY_Msk              (0xFFFFUL << SCB_AIRCR_VECTKEY_Pos)            /*!< SCB AIRCR: VECTKEY Mask */
+
+#define SCB_AIRCR_VECTKEYSTAT_Pos          16U                                            /*!< SCB AIRCR: VECTKEYSTAT Position */
+#define SCB_AIRCR_VECTKEYSTAT_Msk          (0xFFFFUL << SCB_AIRCR_VECTKEYSTAT_Pos)        /*!< SCB AIRCR: VECTKEYSTAT Mask */
+
+#define SCB_AIRCR_ENDIANESS_Pos            15U                                            /*!< SCB AIRCR: ENDIANESS Position */
+#define SCB_AIRCR_ENDIANESS_Msk            (1UL << SCB_AIRCR_ENDIANESS_Pos)               /*!< SCB AIRCR: ENDIANESS Mask */
+
+#define SCB_AIRCR_SYSRESETREQ_Pos           2U                                            /*!< SCB AIRCR: SYSRESETREQ Position */
+#define SCB_AIRCR_SYSRESETREQ_Msk          (1UL << SCB_AIRCR_SYSRESETREQ_Pos)             /*!< SCB AIRCR: SYSRESETREQ Mask */
+
+#define SCB_AIRCR_VECTCLRACTIVE_Pos         1U                                            /*!< SCB AIRCR: VECTCLRACTIVE Position */
+#define SCB_AIRCR_VECTCLRACTIVE_Msk        (1UL << SCB_AIRCR_VECTCLRACTIVE_Pos)           /*!< SCB AIRCR: VECTCLRACTIVE Mask */
+
+/* SCB System Control Register Definitions */
+#define SCB_SCR_SEVONPEND_Pos               4U                                            /*!< SCB SCR: SEVONPEND Position */
+#define SCB_SCR_SEVONPEND_Msk              (1UL << SCB_SCR_SEVONPEND_Pos)                 /*!< SCB SCR: SEVONPEND Mask */
+
+#define SCB_SCR_SLEEPDEEP_Pos               2U                                            /*!< SCB SCR: SLEEPDEEP Position */
+#define SCB_SCR_SLEEPDEEP_Msk              (1UL << SCB_SCR_SLEEPDEEP_Pos)                 /*!< SCB SCR: SLEEPDEEP Mask */
+
+#define SCB_SCR_SLEEPONEXIT_Pos             1U                                            /*!< SCB SCR: SLEEPONEXIT Position */
+#define SCB_SCR_SLEEPONEXIT_Msk            (1UL << SCB_SCR_SLEEPONEXIT_Pos)               /*!< SCB SCR: SLEEPONEXIT Mask */
+
+/* SCB Configuration Control Register Definitions */
+#define SCB_CCR_STKALIGN_Pos                9U                                            /*!< SCB CCR: STKALIGN Position */
+#define SCB_CCR_STKALIGN_Msk               (1UL << SCB_CCR_STKALIGN_Pos)                  /*!< SCB CCR: STKALIGN Mask */
+
+#define SCB_CCR_UNALIGN_TRP_Pos             3U                                            /*!< SCB CCR: UNALIGN_TRP Position */
+#define SCB_CCR_UNALIGN_TRP_Msk            (1UL << SCB_CCR_UNALIGN_TRP_Pos)               /*!< SCB CCR: UNALIGN_TRP Mask */
+
+/* SCB System Handler Control and State Register Definitions */
+#define SCB_SHCSR_SVCALLPENDED_Pos         15U                                            /*!< SCB SHCSR: SVCALLPENDED Position */
+#define SCB_SHCSR_SVCALLPENDED_Msk         (1UL << SCB_SHCSR_SVCALLPENDED_Pos)            /*!< SCB SHCSR: SVCALLPENDED Mask */
+
+/*@} end of group CMSIS_SCB */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SysTick     System Tick Timer (SysTick)
+  \brief    Type definitions for the System Timer Registers.
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Timer (SysTick).
+ */
+typedef struct
+{
+  __IOM uint32_t CTRL;                   /*!< Offset: 0x000 (R/W)  SysTick Control and Status Register */
+  __IOM uint32_t LOAD;                   /*!< Offset: 0x004 (R/W)  SysTick Reload Value Register */
+  __IOM uint32_t VAL;                    /*!< Offset: 0x008 (R/W)  SysTick Current Value Register */
+  __IM  uint32_t CALIB;                  /*!< Offset: 0x00C (R/ )  SysTick Calibration Register */
+} SysTick_Type;
+
+/* SysTick Control / Status Register Definitions */
+#define SysTick_CTRL_COUNTFLAG_Pos         16U                                            /*!< SysTick CTRL: COUNTFLAG Position */
+#define SysTick_CTRL_COUNTFLAG_Msk         (1UL << SysTick_CTRL_COUNTFLAG_Pos)            /*!< SysTick CTRL: COUNTFLAG Mask */
+
+#define SysTick_CTRL_CLKSOURCE_Pos          2U                                            /*!< SysTick CTRL: CLKSOURCE Position */
+#define SysTick_CTRL_CLKSOURCE_Msk         (1UL << SysTick_CTRL_CLKSOURCE_Pos)            /*!< SysTick CTRL: CLKSOURCE Mask */
+
+#define SysTick_CTRL_TICKINT_Pos            1U                                            /*!< SysTick CTRL: TICKINT Position */
+#define SysTick_CTRL_TICKINT_Msk           (1UL << SysTick_CTRL_TICKINT_Pos)              /*!< SysTick CTRL: TICKINT Mask */
+
+#define SysTick_CTRL_ENABLE_Pos             0U                                            /*!< SysTick CTRL: ENABLE Position */
+#define SysTick_CTRL_ENABLE_Msk            (1UL /*<< SysTick_CTRL_ENABLE_Pos*/)           /*!< SysTick CTRL: ENABLE Mask */
+
+/* SysTick Reload Register Definitions */
+#define SysTick_LOAD_RELOAD_Pos             0U                                            /*!< SysTick LOAD: RELOAD Position */
+#define SysTick_LOAD_RELOAD_Msk            (0xFFFFFFUL /*<< SysTick_LOAD_RELOAD_Pos*/)    /*!< SysTick LOAD: RELOAD Mask */
+
+/* SysTick Current Register Definitions */
+#define SysTick_VAL_CURRENT_Pos             0U                                            /*!< SysTick VAL: CURRENT Position */
+#define SysTick_VAL_CURRENT_Msk            (0xFFFFFFUL /*<< SysTick_VAL_CURRENT_Pos*/)    /*!< SysTick VAL: CURRENT Mask */
+
+/* SysTick Calibration Register Definitions */
+#define SysTick_CALIB_NOREF_Pos            31U                                            /*!< SysTick CALIB: NOREF Position */
+#define SysTick_CALIB_NOREF_Msk            (1UL << SysTick_CALIB_NOREF_Pos)               /*!< SysTick CALIB: NOREF Mask */
+
+#define SysTick_CALIB_SKEW_Pos             30U                                            /*!< SysTick CALIB: SKEW Position */
+#define SysTick_CALIB_SKEW_Msk             (1UL << SysTick_CALIB_SKEW_Pos)                /*!< SysTick CALIB: SKEW Mask */
+
+#define SysTick_CALIB_TENMS_Pos             0U                                            /*!< SysTick CALIB: TENMS Position */
+#define SysTick_CALIB_TENMS_Msk            (0xFFFFFFUL /*<< SysTick_CALIB_TENMS_Pos*/)    /*!< SysTick CALIB: TENMS Mask */
+
+/*@} end of group CMSIS_SysTick */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_CoreDebug       Core Debug Registers (CoreDebug)
+  \brief    Cortex-M0 Core Debug Registers (DCB registers, SHCSR, and DFSR) are only accessible over DAP and not via processor.
+            Therefore they are not covered by the Cortex-M0 header file.
+  @{
+ */
+/*@} end of group CMSIS_CoreDebug */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_bitfield     Core register bit field macros
+  \brief      Macros for use with bit field definitions (xxx_Pos, xxx_Msk).
+  @{
+ */
+
+/**
+  \brief   Mask and shift a bit field value for use in a register bit range.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of the bit field. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted value.
+*/
+#define _VAL2FLD(field, value)    (((uint32_t)(value) << field ## _Pos) & field ## _Msk)
+
+/**
+  \brief     Mask and shift a register value to extract a bit filed value.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of register. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted bit field value.
+*/
+#define _FLD2VAL(field, value)    (((uint32_t)(value) & field ## _Msk) >> field ## _Pos)
+
+/*@} end of group CMSIS_core_bitfield */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_base     Core Definitions
+  \brief      Definitions for base addresses, unions, and structures.
+  @{
+ */
+
+/* Memory mapping of Core Hardware */
+#define SCS_BASE            (0xE000E000UL)                            /*!< System Control Space Base Address */
+#define SysTick_BASE        (SCS_BASE +  0x0010UL)                    /*!< SysTick Base Address */
+#define NVIC_BASE           (SCS_BASE +  0x0100UL)                    /*!< NVIC Base Address */
+#define SCB_BASE            (SCS_BASE +  0x0D00UL)                    /*!< System Control Block Base Address */
+
+#define SCB                 ((SCB_Type       *)     SCB_BASE      )   /*!< SCB configuration struct */
+#define SysTick             ((SysTick_Type   *)     SysTick_BASE  )   /*!< SysTick configuration struct */
+#define NVIC                ((NVIC_Type      *)     NVIC_BASE     )   /*!< NVIC configuration struct */
+
+
+/*@} */
+
+
+
+/*******************************************************************************
+ *                Hardware Abstraction Layer
+  Core Function Interface contains:
+  - Core NVIC Functions
+  - Core SysTick Functions
+  - Core Register Access Functions
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_Core_FunctionInterface Functions and Instructions Reference
+*/
+
+
+
+/* ##########################   NVIC functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_NVICFunctions NVIC Functions
+  \brief    Functions that manage interrupts and exceptions via the NVIC.
+  @{
+ */
+
+#ifdef CMSIS_NVIC_VIRTUAL
+  #ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE
+    #define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h"
+  #endif
+  #include CMSIS_NVIC_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetPriorityGrouping    __NVIC_SetPriorityGrouping
+  #define NVIC_GetPriorityGrouping    __NVIC_GetPriorityGrouping
+  #define NVIC_EnableIRQ              __NVIC_EnableIRQ
+  #define NVIC_GetEnableIRQ           __NVIC_GetEnableIRQ
+  #define NVIC_DisableIRQ             __NVIC_DisableIRQ
+  #define NVIC_GetPendingIRQ          __NVIC_GetPendingIRQ
+  #define NVIC_SetPendingIRQ          __NVIC_SetPendingIRQ
+  #define NVIC_ClearPendingIRQ        __NVIC_ClearPendingIRQ
+/*#define NVIC_GetActive              __NVIC_GetActive             not available for Cortex-M0 */
+  #define NVIC_SetPriority            __NVIC_SetPriority
+  #define NVIC_GetPriority            __NVIC_GetPriority
+  #define NVIC_SystemReset            __NVIC_SystemReset
+#endif /* CMSIS_NVIC_VIRTUAL */
+
+#ifdef CMSIS_VECTAB_VIRTUAL
+  #ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+    #define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h"
+  #endif
+  #include CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetVector              __NVIC_SetVector
+  #define NVIC_GetVector              __NVIC_GetVector
+#endif  /* (CMSIS_VECTAB_VIRTUAL) */
+
+#define NVIC_USER_IRQ_OFFSET          16
+
+
+/* The following EXC_RETURN values are saved the LR on exception entry */
+#define EXC_RETURN_HANDLER         (0xFFFFFFF1UL)     /* return to Handler mode, uses MSP after return                               */
+#define EXC_RETURN_THREAD_MSP      (0xFFFFFFF9UL)     /* return to Thread mode, uses MSP after return                                */
+#define EXC_RETURN_THREAD_PSP      (0xFFFFFFFDUL)     /* return to Thread mode, uses PSP after return                                */
+
+
+/* Interrupt Priorities are WORD accessible only under Armv6-M                  */
+/* The following MACROS handle generation of the register offset and byte masks */
+#define _BIT_SHIFT(IRQn)         (  ((((uint32_t)(int32_t)(IRQn))         )      &  0x03UL) * 8UL)
+#define _SHP_IDX(IRQn)           ( (((((uint32_t)(int32_t)(IRQn)) & 0x0FUL)-8UL) >>    2UL)      )
+#define _IP_IDX(IRQn)            (   (((uint32_t)(int32_t)(IRQn))                >>    2UL)      )
+
+#define __NVIC_SetPriorityGrouping(X) (void)(X)
+#define __NVIC_GetPriorityGrouping()  (0U)
+
+/**
+  \brief   Enable Interrupt
+  \details Enables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Enable status
+  \details Returns a device specific interrupt enable status from the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt is not enabled.
+  \return             1  Interrupt is enabled.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISER[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Disable Interrupt
+  \details Disables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+    __DSB();
+    __ISB();
+  }
+}
+
+
+/**
+  \brief   Get Pending Interrupt
+  \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt status is not pending.
+  \return             1  Interrupt status is pending.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Set Pending Interrupt
+  \details Sets the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Clear Pending Interrupt
+  \details Clears the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Set Interrupt Priority
+  \details Sets the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]      IRQn  Interrupt number.
+  \param [in]  priority  Priority to set.
+  \note    The priority cannot be set for every processor exception.
+ */
+__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->IP[_IP_IDX(IRQn)]  = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)]  & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+  else
+  {
+    SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Priority
+  \details Reads the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn  Interrupt number.
+  \return             Interrupt Priority.
+                      Value is aligned automatically to the implemented priority bits of the microcontroller.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn)
+{
+
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+  else
+  {
+    return((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+}
+
+
+/**
+  \brief   Encode Priority
+  \details Encodes the priority for an interrupt with the given priority group,
+           preemptive priority value, and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set.
+  \param [in]     PriorityGroup  Used priority group.
+  \param [in]   PreemptPriority  Preemptive priority value (starting from 0).
+  \param [in]       SubPriority  Subpriority value (starting from 0).
+  \return                        Encoded priority. Value can be used in the function \ref NVIC_SetPriority().
+ */
+__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  return (
+           ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) |
+           ((SubPriority     & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL)))
+         );
+}
+
+
+/**
+  \brief   Decode Priority
+  \details Decodes an interrupt priority value with a given priority group to
+           preemptive priority value and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set.
+  \param [in]         Priority   Priority value, which can be retrieved with the function \ref NVIC_GetPriority().
+  \param [in]     PriorityGroup  Used priority group.
+  \param [out] pPreemptPriority  Preemptive priority value (starting from 0).
+  \param [out]     pSubPriority  Subpriority value (starting from 0).
+ */
+__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL);
+  *pSubPriority     = (Priority                   ) & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL);
+}
+
+
+
+/**
+  \brief   Set Interrupt Vector
+  \details Sets an interrupt vector in SRAM based interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+           Address 0 must be mapped to SRAM.
+  \param [in]   IRQn      Interrupt number
+  \param [in]   vector    Address of interrupt handler function
+ */
+__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector;
+}
+
+
+/**
+  \brief   Get Interrupt Vector
+  \details Reads an interrupt vector from interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn      Interrupt number.
+  \return                 Address of interrupt handler function
+ */
+__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET];
+}
+
+
+/**
+  \brief   System Reset
+  \details Initiates a system reset request to reset the MCU.
+ */
+__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void)
+{
+  __DSB();                                                          /* Ensure all outstanding memory accesses included
+                                                                       buffered write are completed before reset */
+  SCB->AIRCR  = ((0x5FAUL << SCB_AIRCR_VECTKEY_Pos) |
+                 SCB_AIRCR_SYSRESETREQ_Msk);
+  __DSB();                                                          /* Ensure completion of memory access */
+
+  for(;;)                                                           /* wait until reset */
+  {
+    __NOP();
+  }
+}
+
+/*@} end of CMSIS_Core_NVICFunctions */
+
+
+/* ##########################  FPU functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_FpuFunctions FPU Functions
+  \brief    Function that provides FPU type.
+  @{
+ */
+
+/**
+  \brief   get FPU type
+  \details returns the FPU type
+  \returns
+   - \b  0: No FPU
+   - \b  1: Single precision FPU
+   - \b  2: Double + Single precision FPU
+ */
+__STATIC_INLINE uint32_t SCB_GetFPUType(void)
+{
+    return 0U;           /* No FPU */
+}
+
+
+/*@} end of CMSIS_Core_FpuFunctions */
+
+
+
+/* ##################################    SysTick function  ############################################ */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_SysTickFunctions SysTick Functions
+  \brief    Functions that configure the System.
+  @{
+ */
+
+#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U)
+
+/**
+  \brief   System Tick Configuration
+  \details Initializes the System Timer and its interrupt, and starts the System Tick Timer.
+           Counter is in free running mode to generate periodic interrupts.
+  \param [in]  ticks  Number of ticks between two interrupts.
+  \return          0  Function succeeded.
+  \return          1  Function failed.
+  \note    When the variable <b>__Vendor_SysTickConfig</b> is set to 1, then the
+           function <b>SysTick_Config</b> is not included. In this case, the file <b><i>device</i>.h</b>
+           must contain a vendor-specific implementation of this function.
+ */
+__STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks)
+{
+  if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk)
+  {
+    return (1UL);                                                   /* Reload value impossible */
+  }
+
+  SysTick->LOAD  = (uint32_t)(ticks - 1UL);                         /* set reload register */
+  NVIC_SetPriority (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */
+  SysTick->VAL   = 0UL;                                             /* Load the SysTick Counter Value */
+  SysTick->CTRL  = SysTick_CTRL_CLKSOURCE_Msk |
+                   SysTick_CTRL_TICKINT_Msk   |
+                   SysTick_CTRL_ENABLE_Msk;                         /* Enable SysTick IRQ and SysTick Timer */
+  return (0UL);                                                     /* Function successful */
+}
+
+#endif
+
+/*@} end of CMSIS_Core_SysTickFunctions */
+
+
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM0_H_DEPENDANT */
+
+#endif /* __CMSIS_GENERIC */

Drivers/CMSIS/Core/Include/core_cm1.h

@@ -0,0 +1,976 @@
+/**************************************************************************//**
+ * @file     core_cm1.h
+ * @brief    CMSIS Cortex-M1 Core Peripheral Access Layer Header File
+ * @version  V1.0.0
+ * @date     23. July 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef __CORE_CM1_H_GENERIC
+#define __CORE_CM1_H_GENERIC
+
+#include <stdint.h>
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/**
+  \page CMSIS_MISRA_Exceptions  MISRA-C:2004 Compliance Exceptions
+  CMSIS violates the following MISRA-C:2004 rules:
+
+   \li Required Rule 8.5, object/function definition in header file.<br>
+     Function definitions in header files are used to allow 'inlining'.
+
+   \li Required Rule 18.4, declaration of union type or object of union type: '{...}'.<br>
+     Unions are used for effective representation of core registers.
+
+   \li Advisory Rule 19.7, Function-like macro defined.<br>
+     Function-like macros are used to allow more efficient code.
+ */
+
+
+/*******************************************************************************
+ *                 CMSIS definitions
+ ******************************************************************************/
+/**
+  \ingroup Cortex_M1
+  @{
+ */
+
+#include "cmsis_version.h"
+ 
+/*  CMSIS CM1 definitions */
+#define __CM1_CMSIS_VERSION_MAIN  (__CM_CMSIS_VERSION_MAIN)              /*!< \deprecated [31:16] CMSIS HAL main version */
+#define __CM1_CMSIS_VERSION_SUB   (__CM_CMSIS_VERSION_SUB)               /*!< \deprecated [15:0]  CMSIS HAL sub version */
+#define __CM1_CMSIS_VERSION       ((__CM1_CMSIS_VERSION_MAIN << 16U) | \
+                                    __CM1_CMSIS_VERSION_SUB           )  /*!< \deprecated CMSIS HAL version number */
+
+#define __CORTEX_M                (1U)                                   /*!< Cortex-M Core */
+
+/** __FPU_USED indicates whether an FPU is used or not.
+    This core does not support an FPU at all
+*/
+#define __FPU_USED       0U
+
+#if defined ( __CC_ARM )
+  #if defined __TARGET_FPU_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)
+  #if defined __ARM_PCS_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __GNUC__ )
+  #if defined (__VFP_FP__) && !defined(__SOFTFP__)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __ICCARM__ )
+  #if defined __ARMVFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TI_ARM__ )
+  #if defined __TI_VFP_SUPPORT__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TASKING__ )
+  #if defined __FPU_VFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __CSMC__ )
+  #if ( __CSMC__ & 0x400U)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#endif
+
+#include "cmsis_compiler.h"               /* CMSIS compiler specific defines */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM1_H_GENERIC */
+
+#ifndef __CMSIS_GENERIC
+
+#ifndef __CORE_CM1_H_DEPENDANT
+#define __CORE_CM1_H_DEPENDANT
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* check device defines and use defaults */
+#if defined __CHECK_DEVICE_DEFINES
+  #ifndef __CM1_REV
+    #define __CM1_REV               0x0100U
+    #warning "__CM1_REV not defined in device header file; using default!"
+  #endif
+
+  #ifndef __NVIC_PRIO_BITS
+    #define __NVIC_PRIO_BITS          2U
+    #warning "__NVIC_PRIO_BITS not defined in device header file; using default!"
+  #endif
+
+  #ifndef __Vendor_SysTickConfig
+    #define __Vendor_SysTickConfig    0U
+    #warning "__Vendor_SysTickConfig not defined in device header file; using default!"
+  #endif
+#endif
+
+/* IO definitions (access restrictions to peripheral registers) */
+/**
+    \defgroup CMSIS_glob_defs CMSIS Global Defines
+
+    <strong>IO Type Qualifiers</strong> are used
+    \li to specify the access to peripheral variables.
+    \li for automatic generation of peripheral register debug information.
+*/
+#ifdef __cplusplus
+  #define   __I     volatile             /*!< Defines 'read only' permissions */
+#else
+  #define   __I     volatile const       /*!< Defines 'read only' permissions */
+#endif
+#define     __O     volatile             /*!< Defines 'write only' permissions */
+#define     __IO    volatile             /*!< Defines 'read / write' permissions */
+
+/* following defines should be used for structure members */
+#define     __IM     volatile const      /*! Defines 'read only' structure member permissions */
+#define     __OM     volatile            /*! Defines 'write only' structure member permissions */
+#define     __IOM    volatile            /*! Defines 'read / write' structure member permissions */
+
+/*@} end of group Cortex_M1 */
+
+
+
+/*******************************************************************************
+ *                 Register Abstraction
+  Core Register contain:
+  - Core Register
+  - Core NVIC Register
+  - Core SCB Register
+  - Core SysTick Register
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_core_register Defines and Type Definitions
+  \brief Type definitions and defines for Cortex-M processor based devices.
+*/
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_CORE  Status and Control Registers
+  \brief      Core Register type definitions.
+  @{
+ */
+
+/**
+  \brief  Union type to access the Application Program Status Register (APSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:28;              /*!< bit:  0..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} APSR_Type;
+
+/* APSR Register Definitions */
+#define APSR_N_Pos                         31U                                            /*!< APSR: N Position */
+#define APSR_N_Msk                         (1UL << APSR_N_Pos)                            /*!< APSR: N Mask */
+
+#define APSR_Z_Pos                         30U                                            /*!< APSR: Z Position */
+#define APSR_Z_Msk                         (1UL << APSR_Z_Pos)                            /*!< APSR: Z Mask */
+
+#define APSR_C_Pos                         29U                                            /*!< APSR: C Position */
+#define APSR_C_Msk                         (1UL << APSR_C_Pos)                            /*!< APSR: C Mask */
+
+#define APSR_V_Pos                         28U                                            /*!< APSR: V Position */
+#define APSR_V_Msk                         (1UL << APSR_V_Pos)                            /*!< APSR: V Mask */
+
+
+/**
+  \brief  Union type to access the Interrupt Program Status Register (IPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:23;              /*!< bit:  9..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} IPSR_Type;
+
+/* IPSR Register Definitions */
+#define IPSR_ISR_Pos                        0U                                            /*!< IPSR: ISR Position */
+#define IPSR_ISR_Msk                       (0x1FFUL /*<< IPSR_ISR_Pos*/)                  /*!< IPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Special-Purpose Program Status Registers (xPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:15;              /*!< bit:  9..23  Reserved */
+    uint32_t T:1;                        /*!< bit:     24  Thumb bit        (read 0) */
+    uint32_t _reserved1:3;               /*!< bit: 25..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} xPSR_Type;
+
+/* xPSR Register Definitions */
+#define xPSR_N_Pos                         31U                                            /*!< xPSR: N Position */
+#define xPSR_N_Msk                         (1UL << xPSR_N_Pos)                            /*!< xPSR: N Mask */
+
+#define xPSR_Z_Pos                         30U                                            /*!< xPSR: Z Position */
+#define xPSR_Z_Msk                         (1UL << xPSR_Z_Pos)                            /*!< xPSR: Z Mask */
+
+#define xPSR_C_Pos                         29U                                            /*!< xPSR: C Position */
+#define xPSR_C_Msk                         (1UL << xPSR_C_Pos)                            /*!< xPSR: C Mask */
+
+#define xPSR_V_Pos                         28U                                            /*!< xPSR: V Position */
+#define xPSR_V_Msk                         (1UL << xPSR_V_Pos)                            /*!< xPSR: V Mask */
+
+#define xPSR_T_Pos                         24U                                            /*!< xPSR: T Position */
+#define xPSR_T_Msk                         (1UL << xPSR_T_Pos)                            /*!< xPSR: T Mask */
+
+#define xPSR_ISR_Pos                        0U                                            /*!< xPSR: ISR Position */
+#define xPSR_ISR_Msk                       (0x1FFUL /*<< xPSR_ISR_Pos*/)                  /*!< xPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Control Registers (CONTROL).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:1;               /*!< bit:      0  Reserved */
+    uint32_t SPSEL:1;                    /*!< bit:      1  Stack to be used */
+    uint32_t _reserved1:30;              /*!< bit:  2..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} CONTROL_Type;
+
+/* CONTROL Register Definitions */
+#define CONTROL_SPSEL_Pos                   1U                                            /*!< CONTROL: SPSEL Position */
+#define CONTROL_SPSEL_Msk                  (1UL << CONTROL_SPSEL_Pos)                     /*!< CONTROL: SPSEL Mask */
+
+/*@} end of group CMSIS_CORE */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_NVIC  Nested Vectored Interrupt Controller (NVIC)
+  \brief      Type definitions for the NVIC Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the Nested Vectored Interrupt Controller (NVIC).
+ */
+typedef struct
+{
+  __IOM uint32_t ISER[1U];               /*!< Offset: 0x000 (R/W)  Interrupt Set Enable Register */
+        uint32_t RESERVED0[31U];
+  __IOM uint32_t ICER[1U];               /*!< Offset: 0x080 (R/W)  Interrupt Clear Enable Register */
+        uint32_t RSERVED1[31U];
+  __IOM uint32_t ISPR[1U];               /*!< Offset: 0x100 (R/W)  Interrupt Set Pending Register */
+        uint32_t RESERVED2[31U];
+  __IOM uint32_t ICPR[1U];               /*!< Offset: 0x180 (R/W)  Interrupt Clear Pending Register */
+        uint32_t RESERVED3[31U];
+        uint32_t RESERVED4[64U];
+  __IOM uint32_t IP[8U];                 /*!< Offset: 0x300 (R/W)  Interrupt Priority Register */
+}  NVIC_Type;
+
+/*@} end of group CMSIS_NVIC */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SCB     System Control Block (SCB)
+  \brief    Type definitions for the System Control Block Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Control Block (SCB).
+ */
+typedef struct
+{
+  __IM  uint32_t CPUID;                  /*!< Offset: 0x000 (R/ )  CPUID Base Register */
+  __IOM uint32_t ICSR;                   /*!< Offset: 0x004 (R/W)  Interrupt Control and State Register */
+        uint32_t RESERVED0;
+  __IOM uint32_t AIRCR;                  /*!< Offset: 0x00C (R/W)  Application Interrupt and Reset Control Register */
+  __IOM uint32_t SCR;                    /*!< Offset: 0x010 (R/W)  System Control Register */
+  __IOM uint32_t CCR;                    /*!< Offset: 0x014 (R/W)  Configuration Control Register */
+        uint32_t RESERVED1;
+  __IOM uint32_t SHP[2U];                /*!< Offset: 0x01C (R/W)  System Handlers Priority Registers. [0] is RESERVED */
+  __IOM uint32_t SHCSR;                  /*!< Offset: 0x024 (R/W)  System Handler Control and State Register */
+} SCB_Type;
+
+/* SCB CPUID Register Definitions */
+#define SCB_CPUID_IMPLEMENTER_Pos          24U                                            /*!< SCB CPUID: IMPLEMENTER Position */
+#define SCB_CPUID_IMPLEMENTER_Msk          (0xFFUL << SCB_CPUID_IMPLEMENTER_Pos)          /*!< SCB CPUID: IMPLEMENTER Mask */
+
+#define SCB_CPUID_VARIANT_Pos              20U                                            /*!< SCB CPUID: VARIANT Position */
+#define SCB_CPUID_VARIANT_Msk              (0xFUL << SCB_CPUID_VARIANT_Pos)               /*!< SCB CPUID: VARIANT Mask */
+
+#define SCB_CPUID_ARCHITECTURE_Pos         16U                                            /*!< SCB CPUID: ARCHITECTURE Position */
+#define SCB_CPUID_ARCHITECTURE_Msk         (0xFUL << SCB_CPUID_ARCHITECTURE_Pos)          /*!< SCB CPUID: ARCHITECTURE Mask */
+
+#define SCB_CPUID_PARTNO_Pos                4U                                            /*!< SCB CPUID: PARTNO Position */
+#define SCB_CPUID_PARTNO_Msk               (0xFFFUL << SCB_CPUID_PARTNO_Pos)              /*!< SCB CPUID: PARTNO Mask */
+
+#define SCB_CPUID_REVISION_Pos              0U                                            /*!< SCB CPUID: REVISION Position */
+#define SCB_CPUID_REVISION_Msk             (0xFUL /*<< SCB_CPUID_REVISION_Pos*/)          /*!< SCB CPUID: REVISION Mask */
+
+/* SCB Interrupt Control State Register Definitions */
+#define SCB_ICSR_NMIPENDSET_Pos            31U                                            /*!< SCB ICSR: NMIPENDSET Position */
+#define SCB_ICSR_NMIPENDSET_Msk            (1UL << SCB_ICSR_NMIPENDSET_Pos)               /*!< SCB ICSR: NMIPENDSET Mask */
+
+#define SCB_ICSR_PENDSVSET_Pos             28U                                            /*!< SCB ICSR: PENDSVSET Position */
+#define SCB_ICSR_PENDSVSET_Msk             (1UL << SCB_ICSR_PENDSVSET_Pos)                /*!< SCB ICSR: PENDSVSET Mask */
+
+#define SCB_ICSR_PENDSVCLR_Pos             27U                                            /*!< SCB ICSR: PENDSVCLR Position */
+#define SCB_ICSR_PENDSVCLR_Msk             (1UL << SCB_ICSR_PENDSVCLR_Pos)                /*!< SCB ICSR: PENDSVCLR Mask */
+
+#define SCB_ICSR_PENDSTSET_Pos             26U                                            /*!< SCB ICSR: PENDSTSET Position */
+#define SCB_ICSR_PENDSTSET_Msk             (1UL << SCB_ICSR_PENDSTSET_Pos)                /*!< SCB ICSR: PENDSTSET Mask */
+
+#define SCB_ICSR_PENDSTCLR_Pos             25U                                            /*!< SCB ICSR: PENDSTCLR Position */
+#define SCB_ICSR_PENDSTCLR_Msk             (1UL << SCB_ICSR_PENDSTCLR_Pos)                /*!< SCB ICSR: PENDSTCLR Mask */
+
+#define SCB_ICSR_ISRPREEMPT_Pos            23U                                            /*!< SCB ICSR: ISRPREEMPT Position */
+#define SCB_ICSR_ISRPREEMPT_Msk            (1UL << SCB_ICSR_ISRPREEMPT_Pos)               /*!< SCB ICSR: ISRPREEMPT Mask */
+
+#define SCB_ICSR_ISRPENDING_Pos            22U                                            /*!< SCB ICSR: ISRPENDING Position */
+#define SCB_ICSR_ISRPENDING_Msk            (1UL << SCB_ICSR_ISRPENDING_Pos)               /*!< SCB ICSR: ISRPENDING Mask */
+
+#define SCB_ICSR_VECTPENDING_Pos           12U                                            /*!< SCB ICSR: VECTPENDING Position */
+#define SCB_ICSR_VECTPENDING_Msk           (0x1FFUL << SCB_ICSR_VECTPENDING_Pos)          /*!< SCB ICSR: VECTPENDING Mask */
+
+#define SCB_ICSR_VECTACTIVE_Pos             0U                                            /*!< SCB ICSR: VECTACTIVE Position */
+#define SCB_ICSR_VECTACTIVE_Msk            (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/)       /*!< SCB ICSR: VECTACTIVE Mask */
+
+/* SCB Application Interrupt and Reset Control Register Definitions */
+#define SCB_AIRCR_VECTKEY_Pos              16U                                            /*!< SCB AIRCR: VECTKEY Position */
+#define SCB_AIRCR_VECTKEY_Msk              (0xFFFFUL << SCB_AIRCR_VECTKEY_Pos)            /*!< SCB AIRCR: VECTKEY Mask */
+
+#define SCB_AIRCR_VECTKEYSTAT_Pos          16U                                            /*!< SCB AIRCR: VECTKEYSTAT Position */
+#define SCB_AIRCR_VECTKEYSTAT_Msk          (0xFFFFUL << SCB_AIRCR_VECTKEYSTAT_Pos)        /*!< SCB AIRCR: VECTKEYSTAT Mask */
+
+#define SCB_AIRCR_ENDIANESS_Pos            15U                                            /*!< SCB AIRCR: ENDIANESS Position */
+#define SCB_AIRCR_ENDIANESS_Msk            (1UL << SCB_AIRCR_ENDIANESS_Pos)               /*!< SCB AIRCR: ENDIANESS Mask */
+
+#define SCB_AIRCR_SYSRESETREQ_Pos           2U                                            /*!< SCB AIRCR: SYSRESETREQ Position */
+#define SCB_AIRCR_SYSRESETREQ_Msk          (1UL << SCB_AIRCR_SYSRESETREQ_Pos)             /*!< SCB AIRCR: SYSRESETREQ Mask */
+
+#define SCB_AIRCR_VECTCLRACTIVE_Pos         1U                                            /*!< SCB AIRCR: VECTCLRACTIVE Position */
+#define SCB_AIRCR_VECTCLRACTIVE_Msk        (1UL << SCB_AIRCR_VECTCLRACTIVE_Pos)           /*!< SCB AIRCR: VECTCLRACTIVE Mask */
+
+/* SCB System Control Register Definitions */
+#define SCB_SCR_SEVONPEND_Pos               4U                                            /*!< SCB SCR: SEVONPEND Position */
+#define SCB_SCR_SEVONPEND_Msk              (1UL << SCB_SCR_SEVONPEND_Pos)                 /*!< SCB SCR: SEVONPEND Mask */
+
+#define SCB_SCR_SLEEPDEEP_Pos               2U                                            /*!< SCB SCR: SLEEPDEEP Position */
+#define SCB_SCR_SLEEPDEEP_Msk              (1UL << SCB_SCR_SLEEPDEEP_Pos)                 /*!< SCB SCR: SLEEPDEEP Mask */
+
+#define SCB_SCR_SLEEPONEXIT_Pos             1U                                            /*!< SCB SCR: SLEEPONEXIT Position */
+#define SCB_SCR_SLEEPONEXIT_Msk            (1UL << SCB_SCR_SLEEPONEXIT_Pos)               /*!< SCB SCR: SLEEPONEXIT Mask */
+
+/* SCB Configuration Control Register Definitions */
+#define SCB_CCR_STKALIGN_Pos                9U                                            /*!< SCB CCR: STKALIGN Position */
+#define SCB_CCR_STKALIGN_Msk               (1UL << SCB_CCR_STKALIGN_Pos)                  /*!< SCB CCR: STKALIGN Mask */
+
+#define SCB_CCR_UNALIGN_TRP_Pos             3U                                            /*!< SCB CCR: UNALIGN_TRP Position */
+#define SCB_CCR_UNALIGN_TRP_Msk            (1UL << SCB_CCR_UNALIGN_TRP_Pos)               /*!< SCB CCR: UNALIGN_TRP Mask */
+
+/* SCB System Handler Control and State Register Definitions */
+#define SCB_SHCSR_SVCALLPENDED_Pos         15U                                            /*!< SCB SHCSR: SVCALLPENDED Position */
+#define SCB_SHCSR_SVCALLPENDED_Msk         (1UL << SCB_SHCSR_SVCALLPENDED_Pos)            /*!< SCB SHCSR: SVCALLPENDED Mask */
+
+/*@} end of group CMSIS_SCB */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SCnSCB System Controls not in SCB (SCnSCB)
+  \brief    Type definitions for the System Control and ID Register not in the SCB
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Control and ID Register not in the SCB.
+ */
+typedef struct
+{
+        uint32_t RESERVED0[2U];
+  __IOM uint32_t ACTLR;                  /*!< Offset: 0x008 (R/W)  Auxiliary Control Register */
+} SCnSCB_Type;
+
+/* Auxiliary Control Register Definitions */
+#define SCnSCB_ACTLR_ITCMUAEN_Pos            4U                                        /*!< ACTLR: Instruction TCM Upper Alias Enable Position */
+#define SCnSCB_ACTLR_ITCMUAEN_Msk           (1UL << SCnSCB_ACTLR_ITCMUAEN_Pos)         /*!< ACTLR: Instruction TCM Upper Alias Enable Mask */
+
+#define SCnSCB_ACTLR_ITCMLAEN_Pos            3U                                        /*!< ACTLR: Instruction TCM Lower Alias Enable Position */
+#define SCnSCB_ACTLR_ITCMLAEN_Msk           (1UL << SCnSCB_ACTLR_ITCMLAEN_Pos)         /*!< ACTLR: Instruction TCM Lower Alias Enable Mask */
+
+/*@} end of group CMSIS_SCnotSCB */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SysTick     System Tick Timer (SysTick)
+  \brief    Type definitions for the System Timer Registers.
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Timer (SysTick).
+ */
+typedef struct
+{
+  __IOM uint32_t CTRL;                   /*!< Offset: 0x000 (R/W)  SysTick Control and Status Register */
+  __IOM uint32_t LOAD;                   /*!< Offset: 0x004 (R/W)  SysTick Reload Value Register */
+  __IOM uint32_t VAL;                    /*!< Offset: 0x008 (R/W)  SysTick Current Value Register */
+  __IM  uint32_t CALIB;                  /*!< Offset: 0x00C (R/ )  SysTick Calibration Register */
+} SysTick_Type;
+
+/* SysTick Control / Status Register Definitions */
+#define SysTick_CTRL_COUNTFLAG_Pos         16U                                            /*!< SysTick CTRL: COUNTFLAG Position */
+#define SysTick_CTRL_COUNTFLAG_Msk         (1UL << SysTick_CTRL_COUNTFLAG_Pos)            /*!< SysTick CTRL: COUNTFLAG Mask */
+
+#define SysTick_CTRL_CLKSOURCE_Pos          2U                                            /*!< SysTick CTRL: CLKSOURCE Position */
+#define SysTick_CTRL_CLKSOURCE_Msk         (1UL << SysTick_CTRL_CLKSOURCE_Pos)            /*!< SysTick CTRL: CLKSOURCE Mask */
+
+#define SysTick_CTRL_TICKINT_Pos            1U                                            /*!< SysTick CTRL: TICKINT Position */
+#define SysTick_CTRL_TICKINT_Msk           (1UL << SysTick_CTRL_TICKINT_Pos)              /*!< SysTick CTRL: TICKINT Mask */
+
+#define SysTick_CTRL_ENABLE_Pos             0U                                            /*!< SysTick CTRL: ENABLE Position */
+#define SysTick_CTRL_ENABLE_Msk            (1UL /*<< SysTick_CTRL_ENABLE_Pos*/)           /*!< SysTick CTRL: ENABLE Mask */
+
+/* SysTick Reload Register Definitions */
+#define SysTick_LOAD_RELOAD_Pos             0U                                            /*!< SysTick LOAD: RELOAD Position */
+#define SysTick_LOAD_RELOAD_Msk            (0xFFFFFFUL /*<< SysTick_LOAD_RELOAD_Pos*/)    /*!< SysTick LOAD: RELOAD Mask */
+
+/* SysTick Current Register Definitions */
+#define SysTick_VAL_CURRENT_Pos             0U                                            /*!< SysTick VAL: CURRENT Position */
+#define SysTick_VAL_CURRENT_Msk            (0xFFFFFFUL /*<< SysTick_VAL_CURRENT_Pos*/)    /*!< SysTick VAL: CURRENT Mask */
+
+/* SysTick Calibration Register Definitions */
+#define SysTick_CALIB_NOREF_Pos            31U                                            /*!< SysTick CALIB: NOREF Position */
+#define SysTick_CALIB_NOREF_Msk            (1UL << SysTick_CALIB_NOREF_Pos)               /*!< SysTick CALIB: NOREF Mask */
+
+#define SysTick_CALIB_SKEW_Pos             30U                                            /*!< SysTick CALIB: SKEW Position */
+#define SysTick_CALIB_SKEW_Msk             (1UL << SysTick_CALIB_SKEW_Pos)                /*!< SysTick CALIB: SKEW Mask */
+
+#define SysTick_CALIB_TENMS_Pos             0U                                            /*!< SysTick CALIB: TENMS Position */
+#define SysTick_CALIB_TENMS_Msk            (0xFFFFFFUL /*<< SysTick_CALIB_TENMS_Pos*/)    /*!< SysTick CALIB: TENMS Mask */
+
+/*@} end of group CMSIS_SysTick */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_CoreDebug       Core Debug Registers (CoreDebug)
+  \brief    Cortex-M1 Core Debug Registers (DCB registers, SHCSR, and DFSR) are only accessible over DAP and not via processor.
+            Therefore they are not covered by the Cortex-M1 header file.
+  @{
+ */
+/*@} end of group CMSIS_CoreDebug */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_bitfield     Core register bit field macros
+  \brief      Macros for use with bit field definitions (xxx_Pos, xxx_Msk).
+  @{
+ */
+
+/**
+  \brief   Mask and shift a bit field value for use in a register bit range.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of the bit field. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted value.
+*/
+#define _VAL2FLD(field, value)    (((uint32_t)(value) << field ## _Pos) & field ## _Msk)
+
+/**
+  \brief     Mask and shift a register value to extract a bit filed value.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of register. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted bit field value.
+*/
+#define _FLD2VAL(field, value)    (((uint32_t)(value) & field ## _Msk) >> field ## _Pos)
+
+/*@} end of group CMSIS_core_bitfield */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_base     Core Definitions
+  \brief      Definitions for base addresses, unions, and structures.
+  @{
+ */
+
+/* Memory mapping of Core Hardware */
+#define SCS_BASE            (0xE000E000UL)                            /*!< System Control Space Base Address */
+#define SysTick_BASE        (SCS_BASE +  0x0010UL)                    /*!< SysTick Base Address */
+#define NVIC_BASE           (SCS_BASE +  0x0100UL)                    /*!< NVIC Base Address */
+#define SCB_BASE            (SCS_BASE +  0x0D00UL)                    /*!< System Control Block Base Address */
+
+#define SCnSCB              ((SCnSCB_Type    *)     SCS_BASE      )   /*!< System control Register not in SCB */
+#define SCB                 ((SCB_Type       *)     SCB_BASE      )   /*!< SCB configuration struct */
+#define SysTick             ((SysTick_Type   *)     SysTick_BASE  )   /*!< SysTick configuration struct */
+#define NVIC                ((NVIC_Type      *)     NVIC_BASE     )   /*!< NVIC configuration struct */
+
+
+/*@} */
+
+
+
+/*******************************************************************************
+ *                Hardware Abstraction Layer
+  Core Function Interface contains:
+  - Core NVIC Functions
+  - Core SysTick Functions
+  - Core Register Access Functions
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_Core_FunctionInterface Functions and Instructions Reference
+*/
+
+
+
+/* ##########################   NVIC functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_NVICFunctions NVIC Functions
+  \brief    Functions that manage interrupts and exceptions via the NVIC.
+  @{
+ */
+
+#ifdef CMSIS_NVIC_VIRTUAL
+  #ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE
+    #define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h"
+  #endif
+  #include CMSIS_NVIC_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetPriorityGrouping    __NVIC_SetPriorityGrouping
+  #define NVIC_GetPriorityGrouping    __NVIC_GetPriorityGrouping
+  #define NVIC_EnableIRQ              __NVIC_EnableIRQ
+  #define NVIC_GetEnableIRQ           __NVIC_GetEnableIRQ
+  #define NVIC_DisableIRQ             __NVIC_DisableIRQ
+  #define NVIC_GetPendingIRQ          __NVIC_GetPendingIRQ
+  #define NVIC_SetPendingIRQ          __NVIC_SetPendingIRQ
+  #define NVIC_ClearPendingIRQ        __NVIC_ClearPendingIRQ
+/*#define NVIC_GetActive              __NVIC_GetActive             not available for Cortex-M1 */
+  #define NVIC_SetPriority            __NVIC_SetPriority
+  #define NVIC_GetPriority            __NVIC_GetPriority
+  #define NVIC_SystemReset            __NVIC_SystemReset
+#endif /* CMSIS_NVIC_VIRTUAL */
+
+#ifdef CMSIS_VECTAB_VIRTUAL
+  #ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+    #define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h"
+  #endif
+  #include CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetVector              __NVIC_SetVector
+  #define NVIC_GetVector              __NVIC_GetVector
+#endif  /* (CMSIS_VECTAB_VIRTUAL) */
+
+#define NVIC_USER_IRQ_OFFSET          16
+
+
+/* The following EXC_RETURN values are saved the LR on exception entry */
+#define EXC_RETURN_HANDLER         (0xFFFFFFF1UL)     /* return to Handler mode, uses MSP after return                               */
+#define EXC_RETURN_THREAD_MSP      (0xFFFFFFF9UL)     /* return to Thread mode, uses MSP after return                                */
+#define EXC_RETURN_THREAD_PSP      (0xFFFFFFFDUL)     /* return to Thread mode, uses PSP after return                                */
+
+
+/* Interrupt Priorities are WORD accessible only under Armv6-M                  */
+/* The following MACROS handle generation of the register offset and byte masks */
+#define _BIT_SHIFT(IRQn)         (  ((((uint32_t)(int32_t)(IRQn))         )      &  0x03UL) * 8UL)
+#define _SHP_IDX(IRQn)           ( (((((uint32_t)(int32_t)(IRQn)) & 0x0FUL)-8UL) >>    2UL)      )
+#define _IP_IDX(IRQn)            (   (((uint32_t)(int32_t)(IRQn))                >>    2UL)      )
+
+#define __NVIC_SetPriorityGrouping(X) (void)(X)
+#define __NVIC_GetPriorityGrouping()  (0U)
+
+/**
+  \brief   Enable Interrupt
+  \details Enables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Enable status
+  \details Returns a device specific interrupt enable status from the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt is not enabled.
+  \return             1  Interrupt is enabled.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISER[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Disable Interrupt
+  \details Disables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+    __DSB();
+    __ISB();
+  }
+}
+
+
+/**
+  \brief   Get Pending Interrupt
+  \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt status is not pending.
+  \return             1  Interrupt status is pending.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Set Pending Interrupt
+  \details Sets the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Clear Pending Interrupt
+  \details Clears the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Set Interrupt Priority
+  \details Sets the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]      IRQn  Interrupt number.
+  \param [in]  priority  Priority to set.
+  \note    The priority cannot be set for every processor exception.
+ */
+__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->IP[_IP_IDX(IRQn)]  = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)]  & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+  else
+  {
+    SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Priority
+  \details Reads the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn  Interrupt number.
+  \return             Interrupt Priority.
+                      Value is aligned automatically to the implemented priority bits of the microcontroller.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn)
+{
+
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+  else
+  {
+    return((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+}
+
+
+/**
+  \brief   Encode Priority
+  \details Encodes the priority for an interrupt with the given priority group,
+           preemptive priority value, and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set.
+  \param [in]     PriorityGroup  Used priority group.
+  \param [in]   PreemptPriority  Preemptive priority value (starting from 0).
+  \param [in]       SubPriority  Subpriority value (starting from 0).
+  \return                        Encoded priority. Value can be used in the function \ref NVIC_SetPriority().
+ */
+__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  return (
+           ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) |
+           ((SubPriority     & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL)))
+         );
+}
+
+
+/**
+  \brief   Decode Priority
+  \details Decodes an interrupt priority value with a given priority group to
+           preemptive priority value and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set.
+  \param [in]         Priority   Priority value, which can be retrieved with the function \ref NVIC_GetPriority().
+  \param [in]     PriorityGroup  Used priority group.
+  \param [out] pPreemptPriority  Preemptive priority value (starting from 0).
+  \param [out]     pSubPriority  Subpriority value (starting from 0).
+ */
+__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL);
+  *pSubPriority     = (Priority                   ) & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL);
+}
+
+
+
+/**
+  \brief   Set Interrupt Vector
+  \details Sets an interrupt vector in SRAM based interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+           Address 0 must be mapped to SRAM.
+  \param [in]   IRQn      Interrupt number
+  \param [in]   vector    Address of interrupt handler function
+ */
+__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector;
+}
+
+
+/**
+  \brief   Get Interrupt Vector
+  \details Reads an interrupt vector from interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn      Interrupt number.
+  \return                 Address of interrupt handler function
+ */
+__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET];
+}
+
+
+/**
+  \brief   System Reset
+  \details Initiates a system reset request to reset the MCU.
+ */
+__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void)
+{
+  __DSB();                                                          /* Ensure all outstanding memory accesses included
+                                                                       buffered write are completed before reset */
+  SCB->AIRCR  = ((0x5FAUL << SCB_AIRCR_VECTKEY_Pos) |
+                 SCB_AIRCR_SYSRESETREQ_Msk);
+  __DSB();                                                          /* Ensure completion of memory access */
+
+  for(;;)                                                           /* wait until reset */
+  {
+    __NOP();
+  }
+}
+
+/*@} end of CMSIS_Core_NVICFunctions */
+
+
+/* ##########################  FPU functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_FpuFunctions FPU Functions
+  \brief    Function that provides FPU type.
+  @{
+ */
+
+/**
+  \brief   get FPU type
+  \details returns the FPU type
+  \returns
+   - \b  0: No FPU
+   - \b  1: Single precision FPU
+   - \b  2: Double + Single precision FPU
+ */
+__STATIC_INLINE uint32_t SCB_GetFPUType(void)
+{
+    return 0U;           /* No FPU */
+}
+
+
+/*@} end of CMSIS_Core_FpuFunctions */
+
+
+
+/* ##################################    SysTick function  ############################################ */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_SysTickFunctions SysTick Functions
+  \brief    Functions that configure the System.
+  @{
+ */
+
+#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U)
+
+/**
+  \brief   System Tick Configuration
+  \details Initializes the System Timer and its interrupt, and starts the System Tick Timer.
+           Counter is in free running mode to generate periodic interrupts.
+  \param [in]  ticks  Number of ticks between two interrupts.
+  \return          0  Function succeeded.
+  \return          1  Function failed.
+  \note    When the variable <b>__Vendor_SysTickConfig</b> is set to 1, then the
+           function <b>SysTick_Config</b> is not included. In this case, the file <b><i>device</i>.h</b>
+           must contain a vendor-specific implementation of this function.
+ */
+__STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks)
+{
+  if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk)
+  {
+    return (1UL);                                                   /* Reload value impossible */
+  }
+
+  SysTick->LOAD  = (uint32_t)(ticks - 1UL);                         /* set reload register */
+  NVIC_SetPriority (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */
+  SysTick->VAL   = 0UL;                                             /* Load the SysTick Counter Value */
+  SysTick->CTRL  = SysTick_CTRL_CLKSOURCE_Msk |
+                   SysTick_CTRL_TICKINT_Msk   |
+                   SysTick_CTRL_ENABLE_Msk;                         /* Enable SysTick IRQ and SysTick Timer */
+  return (0UL);                                                     /* Function successful */
+}
+
+#endif
+
+/*@} end of CMSIS_Core_SysTickFunctions */
+
+
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM1_H_DEPENDANT */
+
+#endif /* __CMSIS_GENERIC */

Drivers/CMSIS/Core/Include/mpu_armv7.h

@@ -0,0 +1,270 @@
+/******************************************************************************
+ * @file     mpu_armv7.h
+ * @brief    CMSIS MPU API for Armv7-M MPU
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2017-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+ 
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header    /* treat file as system include file */
+#endif
+ 
+#ifndef ARM_MPU_ARMV7_H
+#define ARM_MPU_ARMV7_H
+
+#define ARM_MPU_REGION_SIZE_32B      ((uint8_t)0x04U) ///!< MPU Region Size 32 Bytes
+#define ARM_MPU_REGION_SIZE_64B      ((uint8_t)0x05U) ///!< MPU Region Size 64 Bytes
+#define ARM_MPU_REGION_SIZE_128B     ((uint8_t)0x06U) ///!< MPU Region Size 128 Bytes
+#define ARM_MPU_REGION_SIZE_256B     ((uint8_t)0x07U) ///!< MPU Region Size 256 Bytes
+#define ARM_MPU_REGION_SIZE_512B     ((uint8_t)0x08U) ///!< MPU Region Size 512 Bytes
+#define ARM_MPU_REGION_SIZE_1KB      ((uint8_t)0x09U) ///!< MPU Region Size 1 KByte
+#define ARM_MPU_REGION_SIZE_2KB      ((uint8_t)0x0AU) ///!< MPU Region Size 2 KBytes
+#define ARM_MPU_REGION_SIZE_4KB      ((uint8_t)0x0BU) ///!< MPU Region Size 4 KBytes
+#define ARM_MPU_REGION_SIZE_8KB      ((uint8_t)0x0CU) ///!< MPU Region Size 8 KBytes
+#define ARM_MPU_REGION_SIZE_16KB     ((uint8_t)0x0DU) ///!< MPU Region Size 16 KBytes
+#define ARM_MPU_REGION_SIZE_32KB     ((uint8_t)0x0EU) ///!< MPU Region Size 32 KBytes
+#define ARM_MPU_REGION_SIZE_64KB     ((uint8_t)0x0FU) ///!< MPU Region Size 64 KBytes
+#define ARM_MPU_REGION_SIZE_128KB    ((uint8_t)0x10U) ///!< MPU Region Size 128 KBytes
+#define ARM_MPU_REGION_SIZE_256KB    ((uint8_t)0x11U) ///!< MPU Region Size 256 KBytes
+#define ARM_MPU_REGION_SIZE_512KB    ((uint8_t)0x12U) ///!< MPU Region Size 512 KBytes
+#define ARM_MPU_REGION_SIZE_1MB      ((uint8_t)0x13U) ///!< MPU Region Size 1 MByte
+#define ARM_MPU_REGION_SIZE_2MB      ((uint8_t)0x14U) ///!< MPU Region Size 2 MBytes
+#define ARM_MPU_REGION_SIZE_4MB      ((uint8_t)0x15U) ///!< MPU Region Size 4 MBytes
+#define ARM_MPU_REGION_SIZE_8MB      ((uint8_t)0x16U) ///!< MPU Region Size 8 MBytes
+#define ARM_MPU_REGION_SIZE_16MB     ((uint8_t)0x17U) ///!< MPU Region Size 16 MBytes
+#define ARM_MPU_REGION_SIZE_32MB     ((uint8_t)0x18U) ///!< MPU Region Size 32 MBytes
+#define ARM_MPU_REGION_SIZE_64MB     ((uint8_t)0x19U) ///!< MPU Region Size 64 MBytes
+#define ARM_MPU_REGION_SIZE_128MB    ((uint8_t)0x1AU) ///!< MPU Region Size 128 MBytes
+#define ARM_MPU_REGION_SIZE_256MB    ((uint8_t)0x1BU) ///!< MPU Region Size 256 MBytes
+#define ARM_MPU_REGION_SIZE_512MB    ((uint8_t)0x1CU) ///!< MPU Region Size 512 MBytes
+#define ARM_MPU_REGION_SIZE_1GB      ((uint8_t)0x1DU) ///!< MPU Region Size 1 GByte
+#define ARM_MPU_REGION_SIZE_2GB      ((uint8_t)0x1EU) ///!< MPU Region Size 2 GBytes
+#define ARM_MPU_REGION_SIZE_4GB      ((uint8_t)0x1FU) ///!< MPU Region Size 4 GBytes
+
+#define ARM_MPU_AP_NONE 0U ///!< MPU Access Permission no access
+#define ARM_MPU_AP_PRIV 1U ///!< MPU Access Permission privileged access only
+#define ARM_MPU_AP_URO  2U ///!< MPU Access Permission unprivileged access read-only
+#define ARM_MPU_AP_FULL 3U ///!< MPU Access Permission full access
+#define ARM_MPU_AP_PRO  5U ///!< MPU Access Permission privileged access read-only
+#define ARM_MPU_AP_RO   6U ///!< MPU Access Permission read-only access
+
+/** MPU Region Base Address Register Value
+*
+* \param Region The region to be configured, number 0 to 15.
+* \param BaseAddress The base address for the region.
+*/
+#define ARM_MPU_RBAR(Region, BaseAddress) \
+  (((BaseAddress) & MPU_RBAR_ADDR_Msk) |  \
+   ((Region) & MPU_RBAR_REGION_Msk)    |  \
+   (MPU_RBAR_VALID_Msk))
+
+/**
+* MPU Memory Access Attributes
+* 
+* \param TypeExtField      Type extension field, allows you to configure memory access type, for example strongly ordered, peripheral.
+* \param IsShareable       Region is shareable between multiple bus masters.
+* \param IsCacheable       Region is cacheable, i.e. its value may be kept in cache.
+* \param IsBufferable      Region is bufferable, i.e. using write-back caching. Cacheable but non-bufferable regions use write-through policy.
+*/  
+#define ARM_MPU_ACCESS_(TypeExtField, IsShareable, IsCacheable, IsBufferable)   \
+  ((((TypeExtField ) << MPU_RASR_TEX_Pos) & MPU_RASR_TEX_Msk)                 | \
+   (((IsShareable ) << MPU_RASR_S_Pos) & MPU_RASR_S_Msk)                      | \
+   (((IsCacheable ) << MPU_RASR_C_Pos) & MPU_RASR_C_Msk)                      | \
+   (((IsBufferable ) << MPU_RASR_B_Pos) & MPU_RASR_B_Msk))
+
+/**
+* MPU Region Attribute and Size Register Value
+* 
+* \param DisableExec       Instruction access disable bit, 1= disable instruction fetches.
+* \param AccessPermission  Data access permissions, allows you to configure read/write access for User and Privileged mode.
+* \param AccessAttributes  Memory access attribution, see \ref ARM_MPU_ACCESS_.
+* \param SubRegionDisable  Sub-region disable field.
+* \param Size              Region size of the region to be configured, for example 4K, 8K.
+*/
+#define ARM_MPU_RASR_EX(DisableExec, AccessPermission, AccessAttributes, SubRegionDisable, Size)      \
+  ((((DisableExec ) << MPU_RASR_XN_Pos) & MPU_RASR_XN_Msk)                                          | \
+   (((AccessPermission) << MPU_RASR_AP_Pos) & MPU_RASR_AP_Msk)                                      | \
+   (((AccessAttributes) ) & (MPU_RASR_TEX_Msk | MPU_RASR_S_Msk | MPU_RASR_C_Msk | MPU_RASR_B_Msk)))
+  
+/**
+* MPU Region Attribute and Size Register Value
+* 
+* \param DisableExec       Instruction access disable bit, 1= disable instruction fetches.
+* \param AccessPermission  Data access permissions, allows you to configure read/write access for User and Privileged mode.
+* \param TypeExtField      Type extension field, allows you to configure memory access type, for example strongly ordered, peripheral.
+* \param IsShareable       Region is shareable between multiple bus masters.
+* \param IsCacheable       Region is cacheable, i.e. its value may be kept in cache.
+* \param IsBufferable      Region is bufferable, i.e. using write-back caching. Cacheable but non-bufferable regions use write-through policy.
+* \param SubRegionDisable  Sub-region disable field.
+* \param Size              Region size of the region to be configured, for example 4K, 8K.
+*/                         
+#define ARM_MPU_RASR(DisableExec, AccessPermission, TypeExtField, IsShareable, IsCacheable, IsBufferable, SubRegionDisable, Size) \
+  ARM_MPU_RASR_EX(DisableExec, AccessPermission, ARM_MPU_ACCESS_(TypeExtField, IsShareable, IsCacheable, IsBufferable), SubRegionDisable, Size)
+
+/**
+* MPU Memory Access Attribute for strongly ordered memory.
+*  - TEX: 000b
+*  - Shareable
+*  - Non-cacheable
+*  - Non-bufferable
+*/ 
+#define ARM_MPU_ACCESS_ORDERED ARM_MPU_ACCESS_(0U, 1U, 0U, 0U)
+
+/**
+* MPU Memory Access Attribute for device memory.
+*  - TEX: 000b (if non-shareable) or 010b (if shareable)
+*  - Shareable or non-shareable
+*  - Non-cacheable
+*  - Bufferable (if shareable) or non-bufferable (if non-shareable)
+*
+* \param IsShareable Configures the device memory as shareable or non-shareable.
+*/ 
+#define ARM_MPU_ACCESS_DEVICE(IsShareable) ((IsShareable) ? ARM_MPU_ACCESS_(0U, 1U, 0U, 1U) : ARM_MPU_ACCESS_(2U, 0U, 0U, 0U))
+
+/**
+* MPU Memory Access Attribute for normal memory.
+*  - TEX: 1BBb (reflecting outer cacheability rules)
+*  - Shareable or non-shareable
+*  - Cacheable or non-cacheable (reflecting inner cacheability rules)
+*  - Bufferable or non-bufferable (reflecting inner cacheability rules)
+*
+* \param OuterCp Configures the outer cache policy.
+* \param InnerCp Configures the inner cache policy.
+* \param IsShareable Configures the memory as shareable or non-shareable.
+*/ 
+#define ARM_MPU_ACCESS_NORMAL(OuterCp, InnerCp, IsShareable) ARM_MPU_ACCESS_((4U | (OuterCp)), IsShareable, ((InnerCp) & 2U), ((InnerCp) & 1U))
+
+/**
+* MPU Memory Access Attribute non-cacheable policy.
+*/
+#define ARM_MPU_CACHEP_NOCACHE 0U
+
+/**
+* MPU Memory Access Attribute write-back, write and read allocate policy.
+*/
+#define ARM_MPU_CACHEP_WB_WRA 1U
+
+/**
+* MPU Memory Access Attribute write-through, no write allocate policy.
+*/
+#define ARM_MPU_CACHEP_WT_NWA 2U
+
+/**
+* MPU Memory Access Attribute write-back, no write allocate policy.
+*/
+#define ARM_MPU_CACHEP_WB_NWA 3U
+
+
+/**
+* Struct for a single MPU Region
+*/
+typedef struct {
+  uint32_t RBAR; //!< The region base address register value (RBAR)
+  uint32_t RASR; //!< The region attribute and size register value (RASR) \ref MPU_RASR
+} ARM_MPU_Region_t;
+    
+/** Enable the MPU.
+* \param MPU_Control Default access permissions for unconfigured regions.
+*/
+__STATIC_INLINE void ARM_MPU_Enable(uint32_t MPU_Control)
+{
+  __DSB();
+  __ISB();
+  MPU->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk;
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+}
+
+/** Disable the MPU.
+*/
+__STATIC_INLINE void ARM_MPU_Disable(void)
+{
+  __DSB();
+  __ISB();
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+  MPU->CTRL  &= ~MPU_CTRL_ENABLE_Msk;
+}
+
+/** Clear and disable the given MPU region.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegion(uint32_t rnr)
+{
+  MPU->RNR = rnr;
+  MPU->RASR = 0U;
+}
+
+/** Configure an MPU region.
+* \param rbar Value for RBAR register.
+* \param rsar Value for RSAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegion(uint32_t rbar, uint32_t rasr)
+{
+  MPU->RBAR = rbar;
+  MPU->RASR = rasr;
+}
+
+/** Configure the given MPU region.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rsar Value for RSAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegionEx(uint32_t rnr, uint32_t rbar, uint32_t rasr)
+{
+  MPU->RNR = rnr;
+  MPU->RBAR = rbar;
+  MPU->RASR = rasr;
+}
+
+/** Memcopy with strictly ordered memory access, e.g. for register targets.
+* \param dst Destination data is copied to.
+* \param src Source data is copied from.
+* \param len Amount of data words to be copied.
+*/
+__STATIC_INLINE void orderedCpy(volatile uint32_t* dst, const uint32_t* __RESTRICT src, uint32_t len)
+{
+  uint32_t i;
+  for (i = 0U; i < len; ++i) 
+  {
+    dst[i] = src[i];
+  }
+}
+
+/** Load the given number of MPU regions from a table.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_Load(ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  const uint32_t rowWordSize = sizeof(ARM_MPU_Region_t)/4U;
+  while (cnt > MPU_TYPE_RALIASES) {
+    orderedCpy(&(MPU->RBAR), &(table->RBAR), MPU_TYPE_RALIASES*rowWordSize);
+    table += MPU_TYPE_RALIASES;
+    cnt -= MPU_TYPE_RALIASES;
+  }
+  orderedCpy(&(MPU->RBAR), &(table->RBAR), cnt*rowWordSize);
+}
+
+#endif

Drivers/CMSIS/Core/Include/mpu_armv8.h

@@ -0,0 +1,333 @@
+/******************************************************************************
+ * @file     mpu_armv8.h
+ * @brief    CMSIS MPU API for Armv8-M MPU
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2017-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header    /* treat file as system include file */
+#endif
+
+#ifndef ARM_MPU_ARMV8_H
+#define ARM_MPU_ARMV8_H
+
+/** \brief Attribute for device memory (outer only) */
+#define ARM_MPU_ATTR_DEVICE                           ( 0U )
+
+/** \brief Attribute for non-cacheable, normal memory */
+#define ARM_MPU_ATTR_NON_CACHEABLE                    ( 4U )
+
+/** \brief Attribute for normal memory (outer and inner)
+* \param NT Non-Transient: Set to 1 for non-transient data.
+* \param WB Write-Back: Set to 1 to use write-back update policy.
+* \param RA Read Allocation: Set to 1 to use cache allocation on read miss.
+* \param WA Write Allocation: Set to 1 to use cache allocation on write miss.
+*/
+#define ARM_MPU_ATTR_MEMORY_(NT, WB, RA, WA) \
+  (((NT & 1U) << 3U) | ((WB & 1U) << 2U) | ((RA & 1U) << 1U) | (WA & 1U))
+
+/** \brief Device memory type non Gathering, non Re-ordering, non Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_nGnRnE (0U)
+
+/** \brief Device memory type non Gathering, non Re-ordering, Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_nGnRE  (1U)
+
+/** \brief Device memory type non Gathering, Re-ordering, Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_nGRE   (2U)
+
+/** \brief Device memory type Gathering, Re-ordering, Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_GRE    (3U)
+
+/** \brief Memory Attribute
+* \param O Outer memory attributes
+* \param I O == ARM_MPU_ATTR_DEVICE: Device memory attributes, else: Inner memory attributes
+*/
+#define ARM_MPU_ATTR(O, I) (((O & 0xFU) << 4U) | (((O & 0xFU) != 0U) ? (I & 0xFU) : ((I & 0x3U) << 2U)))
+
+/** \brief Normal memory non-shareable  */
+#define ARM_MPU_SH_NON   (0U)
+
+/** \brief Normal memory outer shareable  */
+#define ARM_MPU_SH_OUTER (2U)
+
+/** \brief Normal memory inner shareable  */
+#define ARM_MPU_SH_INNER (3U)
+
+/** \brief Memory access permissions
+* \param RO Read-Only: Set to 1 for read-only memory.
+* \param NP Non-Privileged: Set to 1 for non-privileged memory.
+*/
+#define ARM_MPU_AP_(RO, NP) (((RO & 1U) << 1U) | (NP & 1U))
+
+/** \brief Region Base Address Register value
+* \param BASE The base address bits [31:5] of a memory region. The value is zero extended. Effective address gets 32 byte aligned.
+* \param SH Defines the Shareability domain for this memory region.
+* \param RO Read-Only: Set to 1 for a read-only memory region.
+* \param NP Non-Privileged: Set to 1 for a non-privileged memory region.
+* \oaram XN eXecute Never: Set to 1 for a non-executable memory region.
+*/
+#define ARM_MPU_RBAR(BASE, SH, RO, NP, XN) \
+  ((BASE & MPU_RBAR_BASE_Msk) | \
+  ((SH << MPU_RBAR_SH_Pos) & MPU_RBAR_SH_Msk) | \
+  ((ARM_MPU_AP_(RO, NP) << MPU_RBAR_AP_Pos) & MPU_RBAR_AP_Msk) | \
+  ((XN << MPU_RBAR_XN_Pos) & MPU_RBAR_XN_Msk))
+
+/** \brief Region Limit Address Register value
+* \param LIMIT The limit address bits [31:5] for this memory region. The value is one extended.
+* \param IDX The attribute index to be associated with this memory region.
+*/
+#define ARM_MPU_RLAR(LIMIT, IDX) \
+  ((LIMIT & MPU_RLAR_LIMIT_Msk) | \
+  ((IDX << MPU_RLAR_AttrIndx_Pos) & MPU_RLAR_AttrIndx_Msk) | \
+  (MPU_RLAR_EN_Msk))
+
+/**
+* Struct for a single MPU Region
+*/
+typedef struct {
+  uint32_t RBAR;                   /*!< Region Base Address Register value */
+  uint32_t RLAR;                   /*!< Region Limit Address Register value */
+} ARM_MPU_Region_t;
+    
+/** Enable the MPU.
+* \param MPU_Control Default access permissions for unconfigured regions.
+*/
+__STATIC_INLINE void ARM_MPU_Enable(uint32_t MPU_Control)
+{
+  __DSB();
+  __ISB();
+  MPU->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk;
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+}
+
+/** Disable the MPU.
+*/
+__STATIC_INLINE void ARM_MPU_Disable(void)
+{
+  __DSB();
+  __ISB();
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+  MPU->CTRL  &= ~MPU_CTRL_ENABLE_Msk;
+}
+
+#ifdef MPU_NS
+/** Enable the Non-secure MPU.
+* \param MPU_Control Default access permissions for unconfigured regions.
+*/
+__STATIC_INLINE void ARM_MPU_Enable_NS(uint32_t MPU_Control)
+{
+  __DSB();
+  __ISB();
+  MPU_NS->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk;
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB_NS->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+}
+
+/** Disable the Non-secure MPU.
+*/
+__STATIC_INLINE void ARM_MPU_Disable_NS(void)
+{
+  __DSB();
+  __ISB();
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB_NS->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+  MPU_NS->CTRL  &= ~MPU_CTRL_ENABLE_Msk;
+}
+#endif
+
+/** Set the memory attribute encoding to the given MPU.
+* \param mpu Pointer to the MPU to be configured.
+* \param idx The attribute index to be set [0-7]
+* \param attr The attribute value to be set.
+*/
+__STATIC_INLINE void ARM_MPU_SetMemAttrEx(MPU_Type* mpu, uint8_t idx, uint8_t attr)
+{
+  const uint8_t reg = idx / 4U;
+  const uint32_t pos = ((idx % 4U) * 8U);
+  const uint32_t mask = 0xFFU << pos;
+  
+  if (reg >= (sizeof(mpu->MAIR) / sizeof(mpu->MAIR[0]))) {
+    return; // invalid index
+  }
+  
+  mpu->MAIR[reg] = ((mpu->MAIR[reg] & ~mask) | ((attr << pos) & mask));
+}
+
+/** Set the memory attribute encoding.
+* \param idx The attribute index to be set [0-7]
+* \param attr The attribute value to be set.
+*/
+__STATIC_INLINE void ARM_MPU_SetMemAttr(uint8_t idx, uint8_t attr)
+{
+  ARM_MPU_SetMemAttrEx(MPU, idx, attr);
+}
+
+#ifdef MPU_NS
+/** Set the memory attribute encoding to the Non-secure MPU.
+* \param idx The attribute index to be set [0-7]
+* \param attr The attribute value to be set.
+*/
+__STATIC_INLINE void ARM_MPU_SetMemAttr_NS(uint8_t idx, uint8_t attr)
+{
+  ARM_MPU_SetMemAttrEx(MPU_NS, idx, attr);
+}
+#endif
+
+/** Clear and disable the given MPU region of the given MPU.
+* \param mpu Pointer to MPU to be used.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegionEx(MPU_Type* mpu, uint32_t rnr)
+{
+  mpu->RNR = rnr;
+  mpu->RLAR = 0U;
+}
+
+/** Clear and disable the given MPU region.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegion(uint32_t rnr)
+{
+  ARM_MPU_ClrRegionEx(MPU, rnr);
+}
+
+#ifdef MPU_NS
+/** Clear and disable the given Non-secure MPU region.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegion_NS(uint32_t rnr)
+{  
+  ARM_MPU_ClrRegionEx(MPU_NS, rnr);
+}
+#endif
+
+/** Configure the given MPU region of the given MPU.
+* \param mpu Pointer to MPU to be used.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rlar Value for RLAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegionEx(MPU_Type* mpu, uint32_t rnr, uint32_t rbar, uint32_t rlar)
+{
+  mpu->RNR = rnr;
+  mpu->RBAR = rbar;
+  mpu->RLAR = rlar;
+}
+
+/** Configure the given MPU region.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rlar Value for RLAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegion(uint32_t rnr, uint32_t rbar, uint32_t rlar)
+{
+  ARM_MPU_SetRegionEx(MPU, rnr, rbar, rlar);
+}
+
+#ifdef MPU_NS
+/** Configure the given Non-secure MPU region.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rlar Value for RLAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegion_NS(uint32_t rnr, uint32_t rbar, uint32_t rlar)
+{
+  ARM_MPU_SetRegionEx(MPU_NS, rnr, rbar, rlar);  
+}
+#endif
+
+/** Memcopy with strictly ordered memory access, e.g. for register targets.
+* \param dst Destination data is copied to.
+* \param src Source data is copied from.
+* \param len Amount of data words to be copied.
+*/
+__STATIC_INLINE void orderedCpy(volatile uint32_t* dst, const uint32_t* __RESTRICT src, uint32_t len)
+{
+  uint32_t i;
+  for (i = 0U; i < len; ++i) 
+  {
+    dst[i] = src[i];
+  }
+}
+
+/** Load the given number of MPU regions from a table to the given MPU.
+* \param mpu Pointer to the MPU registers to be used.
+* \param rnr First region number to be configured.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_LoadEx(MPU_Type* mpu, uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  const uint32_t rowWordSize = sizeof(ARM_MPU_Region_t)/4U;
+  if (cnt == 1U) {
+    mpu->RNR = rnr;
+    orderedCpy(&(mpu->RBAR), &(table->RBAR), rowWordSize);
+  } else {
+    uint32_t rnrBase   = rnr & ~(MPU_TYPE_RALIASES-1U);
+    uint32_t rnrOffset = rnr % MPU_TYPE_RALIASES;
+    
+    mpu->RNR = rnrBase;
+    while ((rnrOffset + cnt) > MPU_TYPE_RALIASES) {
+      uint32_t c = MPU_TYPE_RALIASES - rnrOffset;
+      orderedCpy(&(mpu->RBAR)+(rnrOffset*2U), &(table->RBAR), c*rowWordSize);
+      table += c;
+      cnt -= c;
+      rnrOffset = 0U;
+      rnrBase += MPU_TYPE_RALIASES;
+      mpu->RNR = rnrBase;
+    }
+    
+    orderedCpy(&(mpu->RBAR)+(rnrOffset*2U), &(table->RBAR), cnt*rowWordSize);
+  }
+}
+
+/** Load the given number of MPU regions from a table.
+* \param rnr First region number to be configured.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_Load(uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  ARM_MPU_LoadEx(MPU, rnr, table, cnt);
+}
+
+#ifdef MPU_NS
+/** Load the given number of MPU regions from a table to the Non-secure MPU.
+* \param rnr First region number to be configured.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_Load_NS(uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  ARM_MPU_LoadEx(MPU_NS, rnr, table, cnt);
+}
+#endif
+
+#endif
+

Drivers/CMSIS/Core/Include/tz_context.h

@@ -0,0 +1,70 @@
+/******************************************************************************
+ * @file     tz_context.h
+ * @brief    Context Management for Armv8-M TrustZone
+ * @version  V1.0.1
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2017-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef TZ_CONTEXT_H
+#define TZ_CONTEXT_H
+ 
+#include <stdint.h>
+ 
+#ifndef TZ_MODULEID_T
+#define TZ_MODULEID_T
+/// \details Data type that identifies secure software modules called by a process.
+typedef uint32_t TZ_ModuleId_t;
+#endif
+ 
+/// \details TZ Memory ID identifies an allocated memory slot.
+typedef uint32_t TZ_MemoryId_t;
+  
+/// Initialize secure context memory system
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_InitContextSystem_S (void);
+ 
+/// Allocate context memory for calling secure software modules in TrustZone
+/// \param[in]  module   identifies software modules called from non-secure mode
+/// \return value != 0 id TrustZone memory slot identifier
+/// \return value 0    no memory available or internal error
+TZ_MemoryId_t TZ_AllocModuleContext_S (TZ_ModuleId_t module);
+ 
+/// Free context memory that was previously allocated with \ref TZ_AllocModuleContext_S
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_FreeModuleContext_S (TZ_MemoryId_t id);
+ 
+/// Load secure context (called on RTOS thread context switch)
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_LoadContext_S (TZ_MemoryId_t id);
+ 
+/// Store secure context (called on RTOS thread context switch)
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_StoreContext_S (TZ_MemoryId_t id);
+ 
+#endif  // TZ_CONTEXT_H

Drivers/CMSIS/Core/Template/ARMv8-M/main_s.c

@@ -0,0 +1,58 @@
+/******************************************************************************
+ * @file     main_s.c
+ * @brief    Code template for secure main function
+ * @version  V1.1.1
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2013-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+/* Use CMSE intrinsics */
+#include <arm_cmse.h>
+ 
+#include "RTE_Components.h"
+#include CMSIS_device_header
+ 
+/* TZ_START_NS: Start address of non-secure application */
+#ifndef TZ_START_NS
+#define TZ_START_NS (0x200000U)
+#endif
+ 
+/* typedef for non-secure callback functions */
+typedef void (*funcptr_void) (void) __attribute__((cmse_nonsecure_call));
+ 
+/* Secure main() */
+int main(void) {
+  funcptr_void NonSecure_ResetHandler;
+ 
+  /* Add user setup code for secure part here*/
+ 
+  /* Set non-secure main stack (MSP_NS) */
+  __TZ_set_MSP_NS(*((uint32_t *)(TZ_START_NS)));
+ 
+  /* Get non-secure reset handler */
+  NonSecure_ResetHandler = (funcptr_void)(*((uint32_t *)((TZ_START_NS) + 4U)));
+ 
+  /* Start non-secure state software application */
+  NonSecure_ResetHandler();
+ 
+  /* Non-secure software does not return, this code is not executed */
+  while (1) {
+    __NOP();
+  }
+}

Drivers/CMSIS/Core/Template/ARMv8-M/tz_context.c

@@ -0,0 +1,200 @@
+/******************************************************************************
+ * @file     tz_context.c
+ * @brief    Context Management for Armv8-M TrustZone - Sample implementation
+ * @version  V1.1.1
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2016-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#include "RTE_Components.h"
+#include CMSIS_device_header
+#include "tz_context.h"
+
+/// Number of process slots (threads may call secure library code)
+#ifndef TZ_PROCESS_STACK_SLOTS
+#define TZ_PROCESS_STACK_SLOTS     8U
+#endif
+
+/// Stack size of the secure library code
+#ifndef TZ_PROCESS_STACK_SIZE
+#define TZ_PROCESS_STACK_SIZE      256U
+#endif
+
+typedef struct {
+  uint32_t sp_top;      // stack space top
+  uint32_t sp_limit;    // stack space limit
+  uint32_t sp;          // current stack pointer
+} stack_info_t;
+
+static stack_info_t ProcessStackInfo  [TZ_PROCESS_STACK_SLOTS];
+static uint64_t     ProcessStackMemory[TZ_PROCESS_STACK_SLOTS][TZ_PROCESS_STACK_SIZE/8U];
+static uint32_t     ProcessStackFreeSlot = 0xFFFFFFFFU;
+
+
+/// Initialize secure context memory system
+/// \return execution status (1: success, 0: error)
+__attribute__((cmse_nonsecure_entry))
+uint32_t TZ_InitContextSystem_S (void) {
+  uint32_t n;
+
+  if (__get_IPSR() == 0U) {
+    return 0U;  // Thread Mode
+  }
+
+  for (n = 0U; n < TZ_PROCESS_STACK_SLOTS; n++) {
+    ProcessStackInfo[n].sp = 0U;
+    ProcessStackInfo[n].sp_limit = (uint32_t)&ProcessStackMemory[n];
+    ProcessStackInfo[n].sp_top   = (uint32_t)&ProcessStackMemory[n] + TZ_PROCESS_STACK_SIZE;
+    *((uint32_t *)ProcessStackMemory[n]) = n + 1U;
+  }
+  *((uint32_t *)ProcessStackMemory[--n]) = 0xFFFFFFFFU;
+
+  ProcessStackFreeSlot = 0U;
+
+  // Default process stack pointer and stack limit
+  __set_PSPLIM((uint32_t)ProcessStackMemory);
+  __set_PSP   ((uint32_t)ProcessStackMemory);
+
+  // Privileged Thread Mode using PSP
+  __set_CONTROL(0x02U);
+
+  return 1U;    // Success
+}
+
+
+/// Allocate context memory for calling secure software modules in TrustZone
+/// \param[in]  module   identifies software modules called from non-secure mode
+/// \return value != 0 id TrustZone memory slot identifier
+/// \return value 0    no memory available or internal error
+__attribute__((cmse_nonsecure_entry))
+TZ_MemoryId_t TZ_AllocModuleContext_S (TZ_ModuleId_t module) {
+  uint32_t slot;
+
+  (void)module; // Ignore (fixed Stack size)
+
+  if (__get_IPSR() == 0U) {
+    return 0U;  // Thread Mode
+  }
+
+  if (ProcessStackFreeSlot == 0xFFFFFFFFU) {
+    return 0U;  // No slot available
+  }
+
+  slot = ProcessStackFreeSlot;
+  ProcessStackFreeSlot = *((uint32_t *)ProcessStackMemory[slot]);
+
+  ProcessStackInfo[slot].sp = ProcessStackInfo[slot].sp_top;
+
+  return (slot + 1U);
+}
+
+
+/// Free context memory that was previously allocated with \ref TZ_AllocModuleContext_S
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+__attribute__((cmse_nonsecure_entry))
+uint32_t TZ_FreeModuleContext_S (TZ_MemoryId_t id) {
+  uint32_t slot;
+
+  if (__get_IPSR() == 0U) {
+    return 0U;  // Thread Mode
+  }
+
+  if ((id == 0U) || (id > TZ_PROCESS_STACK_SLOTS)) {
+    return 0U;  // Invalid ID
+  }
+
+  slot = id - 1U;
+
+  if (ProcessStackInfo[slot].sp == 0U) {
+    return 0U;  // Inactive slot
+  }
+  ProcessStackInfo[slot].sp = 0U;
+
+  *((uint32_t *)ProcessStackMemory[slot]) = ProcessStackFreeSlot;
+  ProcessStackFreeSlot = slot;
+
+  return 1U;    // Success
+}
+
+
+/// Load secure context (called on RTOS thread context switch)
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+__attribute__((cmse_nonsecure_entry))
+uint32_t TZ_LoadContext_S (TZ_MemoryId_t id) {
+  uint32_t slot;
+
+  if ((__get_IPSR() == 0U) || ((__get_CONTROL() & 2U) == 0U)) {
+    return 0U;  // Thread Mode or using Main Stack for threads
+  }
+
+  if ((id == 0U) || (id > TZ_PROCESS_STACK_SLOTS)) {
+    return 0U;  // Invalid ID
+  }
+
+  slot = id - 1U;
+
+  if (ProcessStackInfo[slot].sp == 0U) {
+    return 0U;  // Inactive slot
+  }
+
+  // Setup process stack pointer and stack limit
+  __set_PSPLIM(ProcessStackInfo[slot].sp_limit);
+  __set_PSP   (ProcessStackInfo[slot].sp);
+
+  return 1U;    // Success
+}
+
+
+/// Store secure context (called on RTOS thread context switch)
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+__attribute__((cmse_nonsecure_entry))
+uint32_t TZ_StoreContext_S (TZ_MemoryId_t id) {
+  uint32_t slot;
+  uint32_t sp;
+
+  if ((__get_IPSR() == 0U) || ((__get_CONTROL() & 2U) == 0U)) {
+    return 0U;  // Thread Mode or using Main Stack for threads
+  }
+
+  if ((id == 0U) || (id > TZ_PROCESS_STACK_SLOTS)) {
+    return 0U;  // Invalid ID
+  }
+
+  slot = id - 1U;
+
+  if (ProcessStackInfo[slot].sp == 0U) {
+    return 0U;  // Inactive slot
+  }
+
+  sp = __get_PSP();
+  if ((sp < ProcessStackInfo[slot].sp_limit) ||
+      (sp > ProcessStackInfo[slot].sp_top)) {
+    return 0U;  // SP out of range
+  }
+  ProcessStackInfo[slot].sp = sp;
+
+  // Default process stack pointer and stack limit
+  __set_PSPLIM((uint32_t)ProcessStackMemory);
+  __set_PSP   ((uint32_t)ProcessStackMemory);
+
+  return 1U;    // Success
+}

Drivers/CMSIS/Core_A/Include/cmsis_armcc.h

@@ -0,0 +1,544 @@
+/**************************************************************************//**
+ * @file     cmsis_armcc.h
+ * @brief    CMSIS compiler specific macros, functions, instructions
+ * @version  V1.0.2
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef __CMSIS_ARMCC_H
+#define __CMSIS_ARMCC_H
+
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 400677)
+  #error "Please use Arm Compiler Toolchain V4.0.677 or later!"
+#endif
+
+/* CMSIS compiler control architecture macros */
+#if (defined (__TARGET_ARCH_7_A ) && (__TARGET_ARCH_7_A  == 1))
+  #define __ARM_ARCH_7A__           1
+#endif
+
+/* CMSIS compiler specific defines */
+#ifndef   __ASM
+  #define __ASM                                  __asm
+#endif
+#ifndef   __INLINE
+  #define __INLINE                               __inline
+#endif
+#ifndef   __FORCEINLINE
+  #define __FORCEINLINE                          __forceinline
+#endif
+#ifndef   __STATIC_INLINE
+  #define __STATIC_INLINE                        static __inline
+#endif
+#ifndef   __STATIC_FORCEINLINE
+  #define __STATIC_FORCEINLINE                   static __forceinline
+#endif
+#ifndef   __NO_RETURN
+  #define __NO_RETURN                            __declspec(noreturn)
+#endif
+#ifndef   CMSIS_DEPRECATED
+  #define CMSIS_DEPRECATED                       __attribute__((deprecated))
+#endif
+#ifndef   __USED
+  #define __USED                                 __attribute__((used))
+#endif
+#ifndef   __WEAK
+  #define __WEAK                                 __attribute__((weak))
+#endif
+#ifndef   __PACKED
+  #define __PACKED                               __attribute__((packed))
+#endif
+#ifndef   __PACKED_STRUCT
+  #define __PACKED_STRUCT                        __packed struct
+#endif
+#ifndef   __UNALIGNED_UINT16_WRITE
+  #define __UNALIGNED_UINT16_WRITE(addr, val)    ((*((__packed uint16_t *)(addr))) = (val))
+#endif
+#ifndef   __UNALIGNED_UINT16_READ
+  #define __UNALIGNED_UINT16_READ(addr)          (*((const __packed uint16_t *)(addr)))
+#endif
+#ifndef   __UNALIGNED_UINT32_WRITE
+  #define __UNALIGNED_UINT32_WRITE(addr, val)    ((*((__packed uint32_t *)(addr))) = (val))
+#endif
+#ifndef   __UNALIGNED_UINT32_READ
+  #define __UNALIGNED_UINT32_READ(addr)          (*((const __packed uint32_t *)(addr)))
+#endif
+#ifndef   __ALIGNED
+  #define __ALIGNED(x)                           __attribute__((aligned(x)))
+#endif
+#ifndef   __PACKED
+  #define __PACKED                               __attribute__((packed))
+#endif
+
+/* ##########################  Core Instruction Access  ######################### */
+/**
+  \brief   No Operation
+ */
+#define __NOP                             __nop
+
+/**
+  \brief   Wait For Interrupt
+ */
+#define __WFI                             __wfi
+
+/**
+  \brief   Wait For Event
+ */
+#define __WFE                             __wfe
+
+/**
+  \brief   Send Event
+ */
+#define __SEV                             __sev
+
+/**
+  \brief   Instruction Synchronization Barrier
+ */
+#define __ISB() do {\
+                   __schedule_barrier();\
+                   __isb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+/**
+  \brief   Data Synchronization Barrier
+ */
+#define __DSB() do {\
+                   __schedule_barrier();\
+                   __dsb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+/**
+  \brief   Data Memory Barrier
+ */
+#define __DMB() do {\
+                   __schedule_barrier();\
+                   __dmb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+/**
+  \brief   Reverse byte order (32 bit)
+  \details Reverses the byte order in unsigned integer value. For example, 0x12345678 becomes 0x78563412.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#define __REV                             __rev
+
+/**
+  \brief   Reverse byte order (16 bit)
+  \details Reverses the byte order within each halfword of a word. For example, 0x12345678 becomes 0x34127856.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".rev16_text"))) __STATIC_INLINE __ASM uint32_t __REV16(uint32_t value)
+{
+  rev16 r0, r0
+  bx lr
+}
+#endif
+
+/**
+  \brief   Reverse byte order (16 bit)
+  \details Reverses the byte order in a 16-bit value and returns the signed 16-bit result. For example, 0x0080 becomes 0x8000.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".revsh_text"))) __STATIC_INLINE __ASM int16_t __REVSH(int16_t value)
+{
+  revsh r0, r0
+  bx lr
+}
+#endif
+
+/**
+  \brief   Rotate Right in unsigned value (32 bit)
+  \param [in]    op1  Value to rotate
+  \param [in]    op2  Number of Bits to rotate
+  \return               Rotated value
+ */
+#define __ROR                             __ror
+
+/**
+  \brief   Breakpoint
+  \param [in]    value  is ignored by the processor.
+                 If required, a debugger can use it to store additional information about the breakpoint.
+ */
+#define __BKPT(value)                     __breakpoint(value)
+
+/**
+  \brief   Reverse bit order of value
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#define __RBIT                            __rbit
+
+/**
+  \brief   Count leading zeros
+  \param [in]  value  Value to count the leading zeros
+  \return             number of leading zeros in value
+ */
+#define __CLZ                             __clz
+
+/**
+  \brief   LDR Exclusive (8 bit)
+  \details Executes a exclusive LDR instruction for 8 bit value.
+  \param [in]    ptr  Pointer to data
+  \return             value of type uint8_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXB(ptr)                                                        ((uint8_t ) __ldrex(ptr))
+#else
+  #define __LDREXB(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint8_t ) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+/**
+  \brief   LDR Exclusive (16 bit)
+  \details Executes a exclusive LDR instruction for 16 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint16_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXH(ptr)                                                        ((uint16_t) __ldrex(ptr))
+#else
+  #define __LDREXH(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint16_t) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+/**
+  \brief   LDR Exclusive (32 bit)
+  \details Executes a exclusive LDR instruction for 32 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint32_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXW(ptr)                                                        ((uint32_t ) __ldrex(ptr))
+#else
+  #define __LDREXW(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint32_t ) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+/**
+  \brief   STR Exclusive (8 bit)
+  \details Executes a exclusive STR instruction for 8 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXB(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXB(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+/**
+  \brief   STR Exclusive (16 bit)
+  \details Executes a exclusive STR instruction for 16 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXH(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXH(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+/**
+  \brief   STR Exclusive (32 bit)
+  \details Executes a exclusive STR instruction for 32 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXW(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXW(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+/**
+  \brief   Remove the exclusive lock
+  \details Removes the exclusive lock which is created by LDREX.
+ */
+#define __CLREX                           __clrex
+
+
+/**
+  \brief   Signed Saturate
+  \details Saturates a signed value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (1..32)
+  \return             Saturated value
+ */
+#define __SSAT                            __ssat
+
+/**
+  \brief   Unsigned Saturate
+  \details Saturates an unsigned value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (0..31)
+  \return             Saturated value
+ */
+#define __USAT                            __usat
+
+/* ###########################  Core Function Access  ########################### */
+
+/**
+  \brief   Get FPSCR (Floating Point Status/Control)
+  \return               Floating Point Status/Control register value
+ */
+__STATIC_INLINE uint32_t __get_FPSCR(void)
+{
+#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+     (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+  register uint32_t __regfpscr         __ASM("fpscr");
+  return(__regfpscr);
+#else
+   return(0U);
+#endif
+}
+
+/**
+  \brief   Set FPSCR (Floating Point Status/Control)
+  \param [in]    fpscr  Floating Point Status/Control value to set
+ */
+__STATIC_INLINE void __set_FPSCR(uint32_t fpscr)
+{
+#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+     (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+  register uint32_t __regfpscr         __ASM("fpscr");
+  __regfpscr = (fpscr);
+#else
+  (void)fpscr;
+#endif
+}
+
+/** \brief  Get CPSR (Current Program Status Register)
+    \return               CPSR Register value
+ */
+__STATIC_INLINE uint32_t __get_CPSR(void)
+{
+  register uint32_t __regCPSR          __ASM("cpsr");
+  return(__regCPSR);
+}
+
+
+/** \brief  Set CPSR (Current Program Status Register)
+    \param [in]    cpsr  CPSR value to set
+ */
+__STATIC_INLINE void __set_CPSR(uint32_t cpsr)
+{
+  register uint32_t __regCPSR          __ASM("cpsr");
+  __regCPSR = cpsr;
+}
+
+/** \brief  Get Mode
+    \return                Processor Mode
+ */
+__STATIC_INLINE uint32_t __get_mode(void)
+{
+  return (__get_CPSR() & 0x1FU);
+}
+
+/** \brief  Set Mode
+    \param [in]    mode  Mode value to set
+ */
+__STATIC_INLINE __ASM void __set_mode(uint32_t mode)
+{
+  MOV  r1, lr
+  MSR  CPSR_C, r0
+  BX   r1
+}
+
+/** \brief  Get Stack Pointer
+    \return Stack Pointer
+ */
+__STATIC_INLINE __ASM uint32_t __get_SP(void)
+{
+  MOV  r0, sp
+  BX   lr
+}
+
+/** \brief  Set Stack Pointer
+    \param [in]    stack  Stack Pointer value to set
+ */
+__STATIC_INLINE __ASM void __set_SP(uint32_t stack)
+{
+  MOV  sp, r0
+  BX   lr
+}
+
+
+/** \brief  Get USR/SYS Stack Pointer
+    \return USR/SYSStack Pointer
+ */
+__STATIC_INLINE __ASM uint32_t __get_SP_usr(void)
+{
+  ARM
+  PRESERVE8
+
+  MRS     R1, CPSR
+  CPS     #0x1F       ;no effect in USR mode
+  MOV     R0, SP
+  MSR     CPSR_c, R1  ;no effect in USR mode
+  ISB
+  BX      LR
+}
+
+/** \brief  Set USR/SYS Stack Pointer
+    \param [in]    topOfProcStack  USR/SYS Stack Pointer value to set
+ */
+__STATIC_INLINE __ASM void __set_SP_usr(uint32_t topOfProcStack)
+{
+  ARM
+  PRESERVE8
+
+  MRS     R1, CPSR
+  CPS     #0x1F       ;no effect in USR mode
+  MOV     SP, R0
+  MSR     CPSR_c, R1  ;no effect in USR mode
+  ISB
+  BX      LR
+}
+
+/** \brief  Get FPEXC (Floating Point Exception Control Register)
+    \return               Floating Point Exception Control Register value
+ */
+__STATIC_INLINE uint32_t __get_FPEXC(void)
+{
+#if (__FPU_PRESENT == 1)
+  register uint32_t __regfpexc         __ASM("fpexc");
+  return(__regfpexc);
+#else
+  return(0);
+#endif
+}
+
+/** \brief  Set FPEXC (Floating Point Exception Control Register)
+    \param [in]    fpexc  Floating Point Exception Control value to set
+ */
+__STATIC_INLINE void __set_FPEXC(uint32_t fpexc)
+{
+#if (__FPU_PRESENT == 1)
+  register uint32_t __regfpexc         __ASM("fpexc");
+  __regfpexc = (fpexc);
+#endif
+}
+
+/*
+ * Include common core functions to access Coprocessor 15 registers
+ */
+
+#define __get_CP(cp, op1, Rt, CRn, CRm, op2) do { register volatile uint32_t tmp __ASM("cp" # cp ":" # op1 ":c" # CRn ":c" # CRm ":" # op2); (Rt) = tmp; } while(0)
+#define __set_CP(cp, op1, Rt, CRn, CRm, op2) do { register volatile uint32_t tmp __ASM("cp" # cp ":" # op1 ":c" # CRn ":c" # CRm ":" # op2); tmp = (Rt); } while(0)
+#define __get_CP64(cp, op1, Rt, CRm) \
+  do { \
+    uint32_t ltmp, htmp; \
+    __ASM volatile("MRRC p" # cp ", " # op1 ", ltmp, htmp, c" # CRm); \
+    (Rt) = ((((uint64_t)htmp) << 32U) | ((uint64_t)ltmp)); \
+  } while(0)
+
+#define __set_CP64(cp, op1, Rt, CRm) \
+  do { \
+    const uint64_t tmp = (Rt); \
+    const uint32_t ltmp = (uint32_t)(tmp); \
+    const uint32_t htmp = (uint32_t)(tmp >> 32U); \
+    __ASM volatile("MCRR p" # cp ", " # op1 ", ltmp, htmp, c" # CRm); \
+  } while(0)
+
+#include "cmsis_cp15.h"
+
+/** \brief  Enable Floating Point Unit
+
+  Critical section, called from undef handler, so systick is disabled
+ */
+__STATIC_INLINE __ASM void __FPU_Enable(void)
+{
+        ARM
+
+        //Permit access to VFP/NEON, registers by modifying CPACR
+        MRC     p15,0,R1,c1,c0,2
+        ORR     R1,R1,#0x00F00000
+        MCR     p15,0,R1,c1,c0,2
+
+        //Ensure that subsequent instructions occur in the context of VFP/NEON access permitted
+        ISB
+
+        //Enable VFP/NEON
+        VMRS    R1,FPEXC
+        ORR     R1,R1,#0x40000000
+        VMSR    FPEXC,R1
+
+        //Initialise VFP/NEON registers to 0
+        MOV     R2,#0
+
+        //Initialise D16 registers to 0
+        VMOV    D0, R2,R2
+        VMOV    D1, R2,R2
+        VMOV    D2, R2,R2
+        VMOV    D3, R2,R2
+        VMOV    D4, R2,R2
+        VMOV    D5, R2,R2
+        VMOV    D6, R2,R2
+        VMOV    D7, R2,R2
+        VMOV    D8, R2,R2
+        VMOV    D9, R2,R2
+        VMOV    D10,R2,R2
+        VMOV    D11,R2,R2
+        VMOV    D12,R2,R2
+        VMOV    D13,R2,R2
+        VMOV    D14,R2,R2
+        VMOV    D15,R2,R2
+
+  IF {TARGET_FEATURE_EXTENSION_REGISTER_COUNT} == 32
+        //Initialise D32 registers to 0
+        VMOV    D16,R2,R2
+        VMOV    D17,R2,R2
+        VMOV    D18,R2,R2
+        VMOV    D19,R2,R2
+        VMOV    D20,R2,R2
+        VMOV    D21,R2,R2
+        VMOV    D22,R2,R2
+        VMOV    D23,R2,R2
+        VMOV    D24,R2,R2
+        VMOV    D25,R2,R2
+        VMOV    D26,R2,R2
+        VMOV    D27,R2,R2
+        VMOV    D28,R2,R2
+        VMOV    D29,R2,R2
+        VMOV    D30,R2,R2
+        VMOV    D31,R2,R2
+  ENDIF
+
+        //Initialise FPSCR to a known state
+        VMRS    R2,FPSCR
+        LDR     R3,=0x00086060 //Mask off all bits that do not have to be preserved. Non-preserved bits can/should be zero.
+        AND     R2,R2,R3
+        VMSR    FPSCR,R2
+
+        BX      LR
+}
+
+#endif /* __CMSIS_ARMCC_H */

Drivers/CMSIS/Core_A/Include/cmsis_armclang.h

@@ -0,0 +1,503 @@
+/**************************************************************************//**
+ * @file     cmsis_armclang.h
+ * @brief    CMSIS compiler specific macros, functions, instructions
+ * @version  V1.0.2
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef __CMSIS_ARMCLANG_H
+#define __CMSIS_ARMCLANG_H
+
+#pragma clang system_header   /* treat file as system include file */
+
+#ifndef __ARM_COMPAT_H
+#include <arm_compat.h>    /* Compatibility header for Arm Compiler 5 intrinsics */
+#endif
+
+/* CMSIS compiler specific defines */
+#ifndef   __ASM
+  #define __ASM                                  __asm
+#endif
+#ifndef   __INLINE
+  #define __INLINE                               __inline
+#endif
+#ifndef   __FORCEINLINE
+  #define __FORCEINLINE                          __attribute__((always_inline))
+#endif
+#ifndef   __STATIC_INLINE
+  #define __STATIC_INLINE                        static __inline
+#endif
+#ifndef   __STATIC_FORCEINLINE
+  #define __STATIC_FORCEINLINE                   __attribute__((always_inline)) static __inline
+#endif
+#ifndef   __NO_RETURN
+  #define __NO_RETURN                            __attribute__((__noreturn__))
+#endif
+#ifndef   CMSIS_DEPRECATED
+  #define CMSIS_DEPRECATED                       __attribute__((deprecated))
+#endif
+#ifndef   __USED
+  #define __USED                                 __attribute__((used))
+#endif
+#ifndef   __WEAK
+  #define __WEAK                                 __attribute__((weak))
+#endif
+#ifndef   __PACKED
+  #define __PACKED                               __attribute__((packed, aligned(1)))
+#endif
+#ifndef   __PACKED_STRUCT
+  #define __PACKED_STRUCT                        struct __attribute__((packed, aligned(1)))
+#endif
+#ifndef   __UNALIGNED_UINT16_WRITE
+  #pragma clang diagnostic push
+  #pragma clang diagnostic ignored "-Wpacked"
+/*lint -esym(9058, T_UINT16_WRITE)*/ /* disable MISRA 2012 Rule 2.4 for T_UINT16_WRITE */
+  __PACKED_STRUCT T_UINT16_WRITE { uint16_t v; };
+  #pragma clang diagnostic pop
+  #define __UNALIGNED_UINT16_WRITE(addr, val)    (void)((((struct T_UINT16_WRITE *)(void *)(addr))->v) = (val))
+#endif
+#ifndef   __UNALIGNED_UINT16_READ
+  #pragma clang diagnostic push
+  #pragma clang diagnostic ignored "-Wpacked"
+/*lint -esym(9058, T_UINT16_READ)*/ /* disable MISRA 2012 Rule 2.4 for T_UINT16_READ */
+  __PACKED_STRUCT T_UINT16_READ { uint16_t v; };
+  #pragma clang diagnostic pop
+  #define __UNALIGNED_UINT16_READ(addr)          (((const struct T_UINT16_READ *)(const void *)(addr))->v)
+#endif
+#ifndef   __UNALIGNED_UINT32_WRITE
+  #pragma clang diagnostic push
+  #pragma clang diagnostic ignored "-Wpacked"
+/*lint -esym(9058, T_UINT32_WRITE)*/ /* disable MISRA 2012 Rule 2.4 for T_UINT32_WRITE */
+  __PACKED_STRUCT T_UINT32_WRITE { uint32_t v; };
+  #pragma clang diagnostic pop
+  #define __UNALIGNED_UINT32_WRITE(addr, val)    (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val))
+#endif
+#ifndef   __UNALIGNED_UINT32_READ
+  #pragma clang diagnostic push
+  #pragma clang diagnostic ignored "-Wpacked"
+  __PACKED_STRUCT T_UINT32_READ { uint32_t v; };
+  #pragma clang diagnostic pop
+  #define __UNALIGNED_UINT32_READ(addr)          (((const struct T_UINT32_READ *)(const void *)(addr))->v)
+#endif
+#ifndef   __ALIGNED
+  #define __ALIGNED(x)                           __attribute__((aligned(x)))
+#endif
+#ifndef   __PACKED
+  #define __PACKED                               __attribute__((packed))
+#endif
+
+/* ##########################  Core Instruction Access  ######################### */
+/**
+  \brief   No Operation
+ */
+#define __NOP                             __builtin_arm_nop
+
+/**
+  \brief   Wait For Interrupt
+ */
+#define __WFI                             __builtin_arm_wfi
+
+/**
+  \brief   Wait For Event
+ */
+#define __WFE                             __builtin_arm_wfe
+
+/**
+  \brief   Send Event
+ */
+#define __SEV                             __builtin_arm_sev
+
+/**
+  \brief   Instruction Synchronization Barrier
+ */
+#define __ISB() do {\
+                   __schedule_barrier();\
+                   __builtin_arm_isb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+/**
+  \brief   Data Synchronization Barrier
+ */
+#define __DSB() do {\
+                   __schedule_barrier();\
+                   __builtin_arm_dsb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+/**
+  \brief   Data Memory Barrier
+ */
+#define __DMB() do {\
+                   __schedule_barrier();\
+                   __builtin_arm_dmb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+/**
+  \brief   Reverse byte order (32 bit)
+  \details Reverses the byte order in unsigned integer value. For example, 0x12345678 becomes 0x78563412.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#define __REV(value)   __builtin_bswap32(value)
+
+/**
+  \brief   Reverse byte order (16 bit)
+  \details Reverses the byte order within each halfword of a word. For example, 0x12345678 becomes 0x34127856.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#define __REV16(value) __ROR(__REV(value), 16)
+
+
+/**
+  \brief   Reverse byte order (16 bit)
+  \details Reverses the byte order in a 16-bit value and returns the signed 16-bit result. For example, 0x0080 becomes 0x8000.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#define __REVSH(value) (int16_t)__builtin_bswap16(value)
+
+
+/**
+  \brief   Rotate Right in unsigned value (32 bit)
+  \details Rotate Right (immediate) provides the value of the contents of a register rotated by a variable number of bits.
+  \param [in]    op1  Value to rotate
+  \param [in]    op2  Number of Bits to rotate
+  \return               Rotated value
+ */
+__STATIC_FORCEINLINE uint32_t __ROR(uint32_t op1, uint32_t op2)
+{
+  op2 %= 32U;
+  if (op2 == 0U)
+  {
+    return op1;
+  }
+  return (op1 >> op2) | (op1 << (32U - op2));
+}
+
+
+/**
+  \brief   Breakpoint
+  \param [in]    value  is ignored by the processor.
+                 If required, a debugger can use it to store additional information about the breakpoint.
+ */
+#define __BKPT(value)   __ASM volatile ("bkpt "#value)
+
+/**
+  \brief   Reverse bit order of value
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#define __RBIT          __builtin_arm_rbit
+
+/**
+  \brief   Count leading zeros
+  \param [in]  value  Value to count the leading zeros
+  \return             number of leading zeros in value
+ */
+#define __CLZ           (uint8_t)__builtin_clz
+
+/**
+  \brief   LDR Exclusive (8 bit)
+  \details Executes a exclusive LDR instruction for 8 bit value.
+  \param [in]    ptr  Pointer to data
+  \return             value of type uint8_t at (*ptr)
+ */
+#define __LDREXB        (uint8_t)__builtin_arm_ldrex
+
+
+/**
+  \brief   LDR Exclusive (16 bit)
+  \details Executes a exclusive LDR instruction for 16 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint16_t at (*ptr)
+ */
+#define __LDREXH        (uint16_t)__builtin_arm_ldrex
+
+/**
+  \brief   LDR Exclusive (32 bit)
+  \details Executes a exclusive LDR instruction for 32 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint32_t at (*ptr)
+ */
+#define __LDREXW        (uint32_t)__builtin_arm_ldrex
+
+/**
+  \brief   STR Exclusive (8 bit)
+  \details Executes a exclusive STR instruction for 8 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#define __STREXB        (uint32_t)__builtin_arm_strex
+
+/**
+  \brief   STR Exclusive (16 bit)
+  \details Executes a exclusive STR instruction for 16 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#define __STREXH        (uint32_t)__builtin_arm_strex
+
+/**
+  \brief   STR Exclusive (32 bit)
+  \details Executes a exclusive STR instruction for 32 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#define __STREXW        (uint32_t)__builtin_arm_strex
+
+/**
+  \brief   Remove the exclusive lock
+  \details Removes the exclusive lock which is created by LDREX.
+ */
+#define __CLREX             __builtin_arm_clrex
+
+/**
+  \brief   Signed Saturate
+  \details Saturates a signed value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (1..32)
+  \return             Saturated value
+ */
+#define __SSAT             __builtin_arm_ssat
+
+/**
+  \brief   Unsigned Saturate
+  \details Saturates an unsigned value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (0..31)
+  \return             Saturated value
+ */
+#define __USAT             __builtin_arm_usat
+
+
+/* ###########################  Core Function Access  ########################### */
+
+/**
+  \brief   Get FPSCR
+  \details Returns the current value of the Floating Point Status/Control register.
+  \return               Floating Point Status/Control register value
+ */
+#define __get_FPSCR      __builtin_arm_get_fpscr
+
+/**
+  \brief   Set FPSCR
+  \details Assigns the given value to the Floating Point Status/Control register.
+  \param [in]    fpscr  Floating Point Status/Control value to set
+ */
+#define __set_FPSCR      __builtin_arm_set_fpscr
+
+/** \brief  Get CPSR Register
+    \return               CPSR Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_CPSR(void)
+{
+  uint32_t result;
+  __ASM volatile("MRS %0, cpsr" : "=r" (result) );
+  return(result);
+}
+
+/** \brief  Set CPSR Register
+    \param [in]    cpsr  CPSR value to set
+ */
+__STATIC_FORCEINLINE void __set_CPSR(uint32_t cpsr)
+{
+__ASM volatile ("MSR cpsr, %0" : : "r" (cpsr) : "memory");
+}
+
+/** \brief  Get Mode
+    \return                Processor Mode
+ */
+__STATIC_FORCEINLINE uint32_t __get_mode(void)
+{
+	return (__get_CPSR() & 0x1FU);
+}
+
+/** \brief  Set Mode
+    \param [in]    mode  Mode value to set
+ */
+__STATIC_FORCEINLINE void __set_mode(uint32_t mode)
+{
+  __ASM volatile("MSR  cpsr_c, %0" : : "r" (mode) : "memory");
+}
+
+/** \brief  Get Stack Pointer
+    \return Stack Pointer value
+ */
+__STATIC_FORCEINLINE uint32_t __get_SP()
+{
+  uint32_t result;
+  __ASM volatile("MOV  %0, sp" : "=r" (result) : : "memory");
+  return result;
+}
+
+/** \brief  Set Stack Pointer
+    \param [in]    stack  Stack Pointer value to set
+ */
+__STATIC_FORCEINLINE void __set_SP(uint32_t stack)
+{
+  __ASM volatile("MOV  sp, %0" : : "r" (stack) : "memory");
+}
+
+/** \brief  Get USR/SYS Stack Pointer
+    \return USR/SYS Stack Pointer value
+ */
+__STATIC_FORCEINLINE uint32_t __get_SP_usr()
+{
+  uint32_t cpsr;
+  uint32_t result;
+  __ASM volatile(
+    "MRS     %0, cpsr   \n"
+    "CPS     #0x1F      \n" // no effect in USR mode
+    "MOV     %1, sp     \n"
+    "MSR     cpsr_c, %2 \n" // no effect in USR mode
+    "ISB" :  "=r"(cpsr), "=r"(result) : "r"(cpsr) : "memory"
+   );
+  return result;
+}
+
+/** \brief  Set USR/SYS Stack Pointer
+    \param [in]    topOfProcStack  USR/SYS Stack Pointer value to set
+ */
+__STATIC_FORCEINLINE void __set_SP_usr(uint32_t topOfProcStack)
+{
+  uint32_t cpsr;
+  __ASM volatile(
+    "MRS     %0, cpsr   \n"
+    "CPS     #0x1F      \n" // no effect in USR mode
+    "MOV     sp, %1     \n"
+    "MSR     cpsr_c, %2 \n" // no effect in USR mode
+    "ISB" : "=r"(cpsr) : "r" (topOfProcStack), "r"(cpsr) : "memory"
+   );
+}
+
+/** \brief  Get FPEXC
+    \return               Floating Point Exception Control register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_FPEXC(void)
+{
+#if (__FPU_PRESENT == 1)
+  uint32_t result;
+  __ASM volatile("VMRS %0, fpexc" : "=r" (result) : : "memory");
+  return(result);
+#else
+  return(0);
+#endif
+}
+
+/** \brief  Set FPEXC
+    \param [in]    fpexc  Floating Point Exception Control value to set
+ */
+__STATIC_FORCEINLINE void __set_FPEXC(uint32_t fpexc)
+{
+#if (__FPU_PRESENT == 1)
+  __ASM volatile ("VMSR fpexc, %0" : : "r" (fpexc) : "memory");
+#endif
+}
+
+/*
+ * Include common core functions to access Coprocessor 15 registers
+ */
+
+#define __get_CP(cp, op1, Rt, CRn, CRm, op2) __ASM volatile("MRC p" # cp ", " # op1 ", %0, c" # CRn ", c" # CRm ", " # op2 : "=r" (Rt) : : "memory" )
+#define __set_CP(cp, op1, Rt, CRn, CRm, op2) __ASM volatile("MCR p" # cp ", " # op1 ", %0, c" # CRn ", c" # CRm ", " # op2 : : "r" (Rt) : "memory" )
+#define __get_CP64(cp, op1, Rt, CRm)         __ASM volatile("MRRC p" # cp ", " # op1 ", %Q0, %R0, c" # CRm  : "=r" (Rt) : : "memory" )
+#define __set_CP64(cp, op1, Rt, CRm)         __ASM volatile("MCRR p" # cp ", " # op1 ", %Q0, %R0, c" # CRm  : : "r" (Rt) : "memory" )
+
+#include "cmsis_cp15.h"
+
+/** \brief  Enable Floating Point Unit
+
+  Critical section, called from undef handler, so systick is disabled
+ */
+__STATIC_INLINE void __FPU_Enable(void)
+{
+  __ASM volatile(
+    //Permit access to VFP/NEON, registers by modifying CPACR
+    "        MRC     p15,0,R1,c1,c0,2  \n"
+    "        ORR     R1,R1,#0x00F00000 \n"
+    "        MCR     p15,0,R1,c1,c0,2  \n"
+
+    //Ensure that subsequent instructions occur in the context of VFP/NEON access permitted
+    "        ISB                       \n"
+
+    //Enable VFP/NEON
+    "        VMRS    R1,FPEXC          \n"
+    "        ORR     R1,R1,#0x40000000 \n"
+    "        VMSR    FPEXC,R1          \n"
+
+    //Initialise VFP/NEON registers to 0
+    "        MOV     R2,#0             \n"
+
+    //Initialise D16 registers to 0
+    "        VMOV    D0, R2,R2         \n"
+    "        VMOV    D1, R2,R2         \n"
+    "        VMOV    D2, R2,R2         \n"
+    "        VMOV    D3, R2,R2         \n"
+    "        VMOV    D4, R2,R2         \n"
+    "        VMOV    D5, R2,R2         \n"
+    "        VMOV    D6, R2,R2         \n"
+    "        VMOV    D7, R2,R2         \n"
+    "        VMOV    D8, R2,R2         \n"
+    "        VMOV    D9, R2,R2         \n"
+    "        VMOV    D10,R2,R2         \n"
+    "        VMOV    D11,R2,R2         \n"
+    "        VMOV    D12,R2,R2         \n"
+    "        VMOV    D13,R2,R2         \n"
+    "        VMOV    D14,R2,R2         \n"
+    "        VMOV    D15,R2,R2         \n"
+
+#if __ARM_NEON == 1
+    //Initialise D32 registers to 0
+    "        VMOV    D16,R2,R2         \n"
+    "        VMOV    D17,R2,R2         \n"
+    "        VMOV    D18,R2,R2         \n"
+    "        VMOV    D19,R2,R2         \n"
+    "        VMOV    D20,R2,R2         \n"
+    "        VMOV    D21,R2,R2         \n"
+    "        VMOV    D22,R2,R2         \n"
+    "        VMOV    D23,R2,R2         \n"
+    "        VMOV    D24,R2,R2         \n"
+    "        VMOV    D25,R2,R2         \n"
+    "        VMOV    D26,R2,R2         \n"
+    "        VMOV    D27,R2,R2         \n"
+    "        VMOV    D28,R2,R2         \n"
+    "        VMOV    D29,R2,R2         \n"
+    "        VMOV    D30,R2,R2         \n"
+    "        VMOV    D31,R2,R2         \n"
+#endif
+
+    //Initialise FPSCR to a known state
+    "        VMRS    R2,FPSCR          \n"
+    "        LDR     R3,=0x00086060    \n" //Mask off all bits that do not have to be preserved. Non-preserved bits can/should be zero.
+    "        AND     R2,R2,R3          \n"
+    "        VMSR    FPSCR,R2            "
+  );
+}
+
+#endif /* __CMSIS_ARMCLANG_H */

Drivers/CMSIS/Core_A/Include/cmsis_compiler.h

@@ -0,0 +1,201 @@
+/**************************************************************************//**
+ * @file     cmsis_compiler.h
+ * @brief    CMSIS compiler specific macros, functions, instructions
+ * @version  V1.0.2
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef __CMSIS_COMPILER_H
+#define __CMSIS_COMPILER_H
+
+#include <stdint.h>
+
+/*
+ * Arm Compiler 4/5
+ */
+#if   defined ( __CC_ARM )
+  #include "cmsis_armcc.h"
+
+
+/*
+ * Arm Compiler 6 (armclang)
+ */
+#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)
+  #include "cmsis_armclang.h"
+
+
+/*
+ * GNU Compiler
+ */
+#elif defined ( __GNUC__ )
+  #include "cmsis_gcc.h"
+
+
+/*
+ * IAR Compiler
+ */
+#elif defined ( __ICCARM__ )
+  #include "cmsis_iccarm.h"
+
+
+/*
+ * TI Arm Compiler
+ */
+#elif defined ( __TI_ARM__ )
+  #include <cmsis_ccs.h>
+
+  #ifndef   __ASM
+    #define __ASM                     __asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                  inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE           static inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE           static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE      __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    #define __NO_RETURN               __attribute__((noreturn))
+  #endif
+  #ifndef   CMSIS_DEPRECATED
+    #define CMSIS_DEPRECATED          __attribute__((deprecated))
+  #endif
+  #ifndef   __USED
+    #define __USED                    __attribute__((used))
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                    __attribute__((weak))
+  #endif
+  #ifndef   __UNALIGNED_UINT32
+    struct __attribute__((packed)) T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)     (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #define __ALIGNED(x)              __attribute__((aligned(x)))
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                  __attribute__((packed))
+  #endif
+
+
+/*
+ * TASKING Compiler
+ */
+#elif defined ( __TASKING__ )
+  /*
+   * The CMSIS functions have been implemented as intrinsics in the compiler.
+   * Please use "carm -?i" to get an up to date list of all intrinsics,
+   * Including the CMSIS ones.
+   */
+
+  #ifndef   __ASM
+    #define __ASM                     __asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                  inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE           static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE      __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    #define __NO_RETURN               __attribute__((noreturn))
+  #endif
+  #ifndef   CMSIS_DEPRECATED
+    #define CMSIS_DEPRECATED          __attribute__((deprecated))
+  #endif
+  #ifndef   __USED
+    #define __USED                    __attribute__((used))
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                    __attribute__((weak))
+  #endif
+  #ifndef   __UNALIGNED_UINT32
+    struct __packed__ T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)     (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #define __ALIGNED(x)              __align(x)
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                  __packed__
+  #endif
+
+
+/*
+ * COSMIC Compiler
+ */
+#elif defined ( __CSMC__ )
+   #include <cmsis_csm.h>
+
+ #ifndef   __ASM
+    #define __ASM                     _asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                  inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE           static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE      __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    // NO RETURN is automatically detected hence no warning here
+    #define __NO_RETURN
+  #endif
+  #ifndef   __USED
+    #warning No compiler specific solution for __USED. __USED is ignored.
+    #define __USED
+  #endif
+  #ifndef   CMSIS_DEPRECATED
+    #warning No compiler specific solution for CMSIS_DEPRECATED. CMSIS_DEPRECATED is ignored.
+    #define CMSIS_DEPRECATED
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                    __weak
+  #endif
+  #ifndef   __UNALIGNED_UINT32
+    @packed struct T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)     (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #warning No compiler specific solution for __ALIGNED. __ALIGNED is ignored.
+    #define __ALIGNED(x)
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                  @packed
+  #endif
+
+
+#else
+  #error Unknown compiler.
+#endif
+
+
+#endif /* __CMSIS_COMPILER_H */
+

Drivers/CMSIS/Core_A/Include/cmsis_cp15.h

@@ -0,0 +1,514 @@
+/**************************************************************************//**
+ * @file     cmsis_cp15.h
+ * @brief    CMSIS compiler specific macros, functions, instructions
+ * @version  V1.0.1
+ * @date     07. Sep 2017
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2017 ARM Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef __CMSIS_CP15_H
+#define __CMSIS_CP15_H
+
+/** \brief  Get ACTLR
+    \return               Auxiliary Control register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_ACTLR(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 1, 0, 1);
+  return(result);
+}
+
+/** \brief  Set ACTLR
+    \param [in]    actlr  Auxiliary Control value to set
+ */
+__STATIC_FORCEINLINE void __set_ACTLR(uint32_t actlr)
+{
+  __set_CP(15, 0, actlr, 1, 0, 1);
+}
+
+/** \brief  Get CPACR
+    \return               Coprocessor Access Control register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_CPACR(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 1, 0, 2);
+  return result;
+}
+
+/** \brief  Set CPACR
+    \param [in]    cpacr  Coprocessor Access Control value to set
+ */
+__STATIC_FORCEINLINE void __set_CPACR(uint32_t cpacr)
+{
+  __set_CP(15, 0, cpacr, 1, 0, 2);
+}
+
+/** \brief  Get DFSR
+    \return               Data Fault Status Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_DFSR(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 5, 0, 0);
+  return result;
+}
+
+/** \brief  Set DFSR
+    \param [in]    dfsr  Data Fault Status value to set
+ */
+__STATIC_FORCEINLINE void __set_DFSR(uint32_t dfsr)
+{
+  __set_CP(15, 0, dfsr, 5, 0, 0);
+}
+
+/** \brief  Get IFSR
+    \return               Instruction Fault Status Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_IFSR(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 5, 0, 1);
+  return result;
+}
+
+/** \brief  Set IFSR
+    \param [in]    ifsr  Instruction Fault Status value to set
+ */
+__STATIC_FORCEINLINE void __set_IFSR(uint32_t ifsr)
+{
+  __set_CP(15, 0, ifsr, 5, 0, 1);
+}
+
+/** \brief  Get ISR
+    \return               Interrupt Status Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_ISR(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 12, 1, 0);
+  return result;
+}
+
+/** \brief  Get CBAR
+    \return               Configuration Base Address register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_CBAR(void)
+{
+  uint32_t result;
+  __get_CP(15, 4, result, 15, 0, 0);
+  return result;
+}
+
+/** \brief  Get TTBR0
+
+    This function returns the value of the Translation Table Base Register 0.
+
+    \return               Translation Table Base Register 0 value
+ */
+__STATIC_FORCEINLINE uint32_t __get_TTBR0(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 2, 0, 0);
+  return result;
+}
+
+/** \brief  Set TTBR0
+
+    This function assigns the given value to the Translation Table Base Register 0.
+
+    \param [in]    ttbr0  Translation Table Base Register 0 value to set
+ */
+__STATIC_FORCEINLINE void __set_TTBR0(uint32_t ttbr0)
+{
+  __set_CP(15, 0, ttbr0, 2, 0, 0);
+}
+
+/** \brief  Get DACR
+
+    This function returns the value of the Domain Access Control Register.
+
+    \return               Domain Access Control Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_DACR(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 3, 0, 0);
+  return result;
+}
+
+/** \brief  Set DACR
+
+    This function assigns the given value to the Domain Access Control Register.
+
+    \param [in]    dacr   Domain Access Control Register value to set
+ */
+__STATIC_FORCEINLINE void __set_DACR(uint32_t dacr)
+{
+  __set_CP(15, 0, dacr, 3, 0, 0);
+}
+
+/** \brief  Set SCTLR
+
+    This function assigns the given value to the System Control Register.
+
+    \param [in]    sctlr  System Control Register value to set
+ */
+__STATIC_FORCEINLINE void __set_SCTLR(uint32_t sctlr)
+{
+  __set_CP(15, 0, sctlr, 1, 0, 0);
+}
+
+/** \brief  Get SCTLR
+    \return               System Control Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_SCTLR(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 1, 0, 0);
+  return result;
+}
+
+/** \brief  Set ACTRL
+    \param [in]    actrl  Auxiliary Control Register value to set
+ */
+__STATIC_FORCEINLINE void __set_ACTRL(uint32_t actrl)
+{
+  __set_CP(15, 0, actrl, 1, 0, 1);
+}
+
+/** \brief  Get ACTRL
+    \return               Auxiliary Control Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_ACTRL(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 1, 0, 1);
+  return result;
+}
+
+/** \brief  Get MPIDR
+
+    This function returns the value of the Multiprocessor Affinity Register.
+
+    \return               Multiprocessor Affinity Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_MPIDR(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 0, 0, 5);
+  return result;
+}
+
+/** \brief  Get VBAR
+
+    This function returns the value of the Vector Base Address Register.
+
+    \return               Vector Base Address Register
+ */
+__STATIC_FORCEINLINE uint32_t __get_VBAR(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 12, 0, 0);
+  return result;
+}
+
+/** \brief  Set VBAR
+
+    This function assigns the given value to the Vector Base Address Register.
+
+    \param [in]    vbar  Vector Base Address Register value to set
+ */
+__STATIC_FORCEINLINE void __set_VBAR(uint32_t vbar)
+{
+  __set_CP(15, 0, vbar, 12, 0, 0);
+}
+
+/** \brief  Get MVBAR
+
+    This function returns the value of the Monitor Vector Base Address Register.
+
+    \return               Monitor Vector Base Address Register
+ */
+__STATIC_FORCEINLINE uint32_t __get_MVBAR(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 12, 0, 1);
+  return result;
+}
+
+/** \brief  Set MVBAR
+
+    This function assigns the given value to the Monitor Vector Base Address Register.
+
+    \param [in]    mvbar  Monitor Vector Base Address Register value to set
+ */
+__STATIC_FORCEINLINE void __set_MVBAR(uint32_t mvbar)
+{
+  __set_CP(15, 0, mvbar, 12, 0, 1);
+}
+
+#if (defined(__CORTEX_A) && (__CORTEX_A == 7U) && \
+    defined(__TIM_PRESENT) && (__TIM_PRESENT == 1U)) || \
+    defined(DOXYGEN)
+
+/** \brief  Set CNTFRQ
+
+  This function assigns the given value to PL1 Physical Timer Counter Frequency Register (CNTFRQ).
+
+  \param [in]    value  CNTFRQ Register value to set
+*/
+__STATIC_FORCEINLINE void __set_CNTFRQ(uint32_t value)
+{
+  __set_CP(15, 0, value, 14, 0, 0);
+}
+
+/** \brief  Get CNTFRQ
+
+    This function returns the value of the PL1 Physical Timer Counter Frequency Register (CNTFRQ).
+
+    \return               CNTFRQ Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_CNTFRQ(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 14, 0 , 0);
+  return result;
+}
+
+/** \brief  Set CNTP_TVAL
+
+  This function assigns the given value to PL1 Physical Timer Value Register (CNTP_TVAL).
+
+  \param [in]    value  CNTP_TVAL Register value to set
+*/
+__STATIC_FORCEINLINE void __set_CNTP_TVAL(uint32_t value)
+{
+  __set_CP(15, 0, value, 14, 2, 0);
+}
+
+/** \brief  Get CNTP_TVAL
+
+    This function returns the value of the PL1 Physical Timer Value Register (CNTP_TVAL).
+
+    \return               CNTP_TVAL Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_CNTP_TVAL(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 14, 2, 0);
+  return result;
+}
+
+/** \brief  Get CNTPCT
+
+    This function returns the value of the 64 bits PL1 Physical Count Register (CNTPCT).
+
+    \return               CNTPCT Register value
+ */
+__STATIC_FORCEINLINE uint64_t __get_CNTPCT(void)
+{
+  uint64_t result;
+  __get_CP64(15, 0, result, 14);
+  return result;
+}
+
+/** \brief  Set CNTP_CVAL
+
+  This function assigns the given value to 64bits PL1 Physical Timer CompareValue Register (CNTP_CVAL).
+
+  \param [in]    value  CNTP_CVAL Register value to set
+*/
+__STATIC_FORCEINLINE void __set_CNTP_CVAL(uint64_t value)
+{
+  __set_CP64(15, 2, value, 14);
+}
+
+/** \brief  Get CNTP_CVAL
+
+    This function returns the value of the 64 bits PL1 Physical Timer CompareValue Register (CNTP_CVAL).
+
+    \return               CNTP_CVAL Register value
+ */
+__STATIC_FORCEINLINE uint64_t __get_CNTP_CVAL(void)
+{
+  uint64_t result;
+  __get_CP64(15, 2, result, 14);
+  return result;
+}
+
+/** \brief  Set CNTP_CTL
+
+  This function assigns the given value to PL1 Physical Timer Control Register (CNTP_CTL).
+
+  \param [in]    value  CNTP_CTL Register value to set
+*/
+__STATIC_FORCEINLINE void __set_CNTP_CTL(uint32_t value)
+{
+  __set_CP(15, 0, value, 14, 2, 1);
+}
+
+/** \brief  Get CNTP_CTL register
+    \return               CNTP_CTL Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_CNTP_CTL(void)
+{
+  uint32_t result;
+  __get_CP(15, 0, result, 14, 2, 1);
+  return result;
+}
+
+#endif
+
+/** \brief  Set TLBIALL
+
+  TLB Invalidate All
+ */
+__STATIC_FORCEINLINE void __set_TLBIALL(uint32_t value)
+{
+  __set_CP(15, 0, value, 8, 7, 0);
+}
+
+/** \brief  Set BPIALL.
+
+  Branch Predictor Invalidate All
+ */
+__STATIC_FORCEINLINE void __set_BPIALL(uint32_t value)
+{
+  __set_CP(15, 0, value, 7, 5, 6);
+}
+
+/** \brief  Set ICIALLU
+
+  Instruction Cache Invalidate All
+ */
+__STATIC_FORCEINLINE void __set_ICIALLU(uint32_t value)
+{
+  __set_CP(15, 0, value, 7, 5, 0);
+}
+
+/** \brief  Set DCCMVAC
+
+  Data cache clean
+ */
+__STATIC_FORCEINLINE void __set_DCCMVAC(uint32_t value)
+{
+  __set_CP(15, 0, value, 7, 10, 1);
+}
+
+/** \brief  Set DCIMVAC
+
+  Data cache invalidate
+ */
+__STATIC_FORCEINLINE void __set_DCIMVAC(uint32_t value)
+{
+  __set_CP(15, 0, value, 7, 6, 1);
+}
+
+/** \brief  Set DCCIMVAC
+
+  Data cache clean and invalidate
+ */
+__STATIC_FORCEINLINE void __set_DCCIMVAC(uint32_t value)
+{
+  __set_CP(15, 0, value, 7, 14, 1);
+}
+
+/** \brief  Set CSSELR
+ */
+__STATIC_FORCEINLINE void __set_CSSELR(uint32_t value)
+{
+//  __ASM volatile("MCR p15, 2, %0, c0, c0, 0" : : "r"(value) : "memory");
+  __set_CP(15, 2, value, 0, 0, 0);
+}
+
+/** \brief  Get CSSELR
+    \return CSSELR Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_CSSELR(void)
+{
+  uint32_t result;
+//  __ASM volatile("MRC p15, 2, %0, c0, c0, 0" : "=r"(result) : : "memory");
+  __get_CP(15, 2, result, 0, 0, 0);
+  return result;
+}
+
+/** \brief  Set CCSIDR
+    \deprecated CCSIDR itself is read-only. Use __set_CSSELR to select cache level instead.
+ */
+CMSIS_DEPRECATED
+__STATIC_FORCEINLINE void __set_CCSIDR(uint32_t value)
+{
+  __set_CSSELR(value);
+}
+
+/** \brief  Get CCSIDR
+    \return CCSIDR Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_CCSIDR(void)
+{
+  uint32_t result;
+//  __ASM volatile("MRC p15, 1, %0, c0, c0, 0" : "=r"(result) : : "memory");
+  __get_CP(15, 1, result, 0, 0, 0);
+  return result;
+}
+
+/** \brief  Get CLIDR
+    \return CLIDR Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_CLIDR(void)
+{
+  uint32_t result;
+//  __ASM volatile("MRC p15, 1, %0, c0, c0, 1" : "=r"(result) : : "memory");
+  __get_CP(15, 1, result, 0, 0, 1);
+  return result;
+}
+
+/** \brief  Set DCISW
+ */
+__STATIC_FORCEINLINE void __set_DCISW(uint32_t value)
+{
+//  __ASM volatile("MCR p15, 0, %0, c7, c6, 2" : : "r"(value) : "memory")
+  __set_CP(15, 0, value, 7, 6, 2);
+}
+
+/** \brief  Set DCCSW
+ */
+__STATIC_FORCEINLINE void __set_DCCSW(uint32_t value)
+{
+//  __ASM volatile("MCR p15, 0, %0, c7, c10, 2" : : "r"(value) : "memory")
+  __set_CP(15, 0, value, 7, 10, 2);
+}
+
+/** \brief  Set DCCISW
+ */
+__STATIC_FORCEINLINE void __set_DCCISW(uint32_t value)
+{
+//  __ASM volatile("MCR p15, 0, %0, c7, c14, 2" : : "r"(value) : "memory")
+  __set_CP(15, 0, value, 7, 14, 2);
+}
+
+#endif

Drivers/CMSIS/Core_A/Include/cmsis_gcc.h

@@ -0,0 +1,679 @@
+/**************************************************************************//**
+ * @file     cmsis_gcc.h
+ * @brief    CMSIS compiler specific macros, functions, instructions
+ * @version  V1.0.2
+ * @date     09. April 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef __CMSIS_GCC_H
+#define __CMSIS_GCC_H
+
+/* ignore some GCC warnings */
+#pragma GCC diagnostic push
+#pragma GCC diagnostic ignored "-Wsign-conversion"
+#pragma GCC diagnostic ignored "-Wconversion"
+#pragma GCC diagnostic ignored "-Wunused-parameter"
+
+/* Fallback for __has_builtin */
+#ifndef __has_builtin
+  #define __has_builtin(x) (0)
+#endif
+
+/* CMSIS compiler specific defines */
+#ifndef   __ASM
+  #define __ASM                                  asm
+#endif
+#ifndef   __INLINE
+  #define __INLINE                               inline
+#endif
+#ifndef   __FORCEINLINE
+  #define __FORCEINLINE                          __attribute__((always_inline))
+#endif
+#ifndef   __STATIC_INLINE
+  #define __STATIC_INLINE                        static inline
+#endif
+#ifndef   __STATIC_FORCEINLINE
+  #define __STATIC_FORCEINLINE                   __attribute__((always_inline)) static inline
+#endif
+#ifndef   __NO_RETURN
+  #define __NO_RETURN                            __attribute__((__noreturn__))
+#endif
+#ifndef   CMSIS_DEPRECATED
+ #define  CMSIS_DEPRECATED                       __attribute__((deprecated))
+#endif
+#ifndef   __USED
+  #define __USED                                 __attribute__((used))
+#endif
+#ifndef   __WEAK
+  #define __WEAK                                 __attribute__((weak))
+#endif
+#ifndef   __PACKED
+  #define __PACKED                               __attribute__((packed, aligned(1)))
+#endif
+#ifndef   __PACKED_STRUCT
+  #define __PACKED_STRUCT                        struct __attribute__((packed, aligned(1)))
+#endif
+#ifndef   __UNALIGNED_UINT16_WRITE
+  #pragma GCC diagnostic push
+  #pragma GCC diagnostic ignored "-Wpacked"
+/*lint -esym(9058, T_UINT16_WRITE)*/ /* disable MISRA 2012 Rule 2.4 for T_UINT16_WRITE */
+  __PACKED_STRUCT T_UINT16_WRITE { uint16_t v; };
+  #pragma GCC diagnostic pop
+  #define __UNALIGNED_UINT16_WRITE(addr, val)    (void)((((struct T_UINT16_WRITE *)(void *)(addr))->v) = (val))
+#endif
+#ifndef   __UNALIGNED_UINT16_READ
+  #pragma GCC diagnostic push
+  #pragma GCC diagnostic ignored "-Wpacked"
+/*lint -esym(9058, T_UINT16_READ)*/ /* disable MISRA 2012 Rule 2.4 for T_UINT16_READ */
+  __PACKED_STRUCT T_UINT16_READ { uint16_t v; };
+  #pragma GCC diagnostic pop
+  #define __UNALIGNED_UINT16_READ(addr)          (((const struct T_UINT16_READ *)(const void *)(addr))->v)
+#endif
+#ifndef   __UNALIGNED_UINT32_WRITE
+  #pragma GCC diagnostic push
+  #pragma GCC diagnostic ignored "-Wpacked"
+/*lint -esym(9058, T_UINT32_WRITE)*/ /* disable MISRA 2012 Rule 2.4 for T_UINT32_WRITE */
+  __PACKED_STRUCT T_UINT32_WRITE { uint32_t v; };
+  #pragma GCC diagnostic pop
+  #define __UNALIGNED_UINT32_WRITE(addr, val)    (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val))
+#endif
+#ifndef   __UNALIGNED_UINT32_READ
+  #pragma GCC diagnostic push
+  #pragma GCC diagnostic ignored "-Wpacked"
+  __PACKED_STRUCT T_UINT32_READ { uint32_t v; };
+  #pragma GCC diagnostic pop
+  #define __UNALIGNED_UINT32_READ(addr)          (((const struct T_UINT32_READ *)(const void *)(addr))->v)
+#endif
+#ifndef   __ALIGNED
+  #define __ALIGNED(x)                           __attribute__((aligned(x)))
+#endif
+
+/* ##########################  Core Instruction Access  ######################### */
+/**
+  \brief   No Operation
+ */
+#define __NOP()                             __ASM volatile ("nop")
+
+/**
+  \brief   Wait For Interrupt
+ */
+#define __WFI()                             __ASM volatile ("wfi")
+
+/**
+  \brief   Wait For Event
+ */
+#define __WFE()                             __ASM volatile ("wfe")
+
+/**
+  \brief   Send Event
+ */
+#define __SEV()                             __ASM volatile ("sev")
+
+/**
+  \brief   Instruction Synchronization Barrier
+  \details Instruction Synchronization Barrier flushes the pipeline in the processor,
+           so that all instructions following the ISB are fetched from cache or memory,
+           after the instruction has been completed.
+ */
+__STATIC_FORCEINLINE  void __ISB(void)
+{
+  __ASM volatile ("isb 0xF":::"memory");
+}
+
+
+/**
+  \brief   Data Synchronization Barrier
+  \details Acts as a special kind of Data Memory Barrier.
+           It completes when all explicit memory accesses before this instruction complete.
+ */
+__STATIC_FORCEINLINE  void __DSB(void)
+{
+  __ASM volatile ("dsb 0xF":::"memory");
+}
+
+/**
+  \brief   Data Memory Barrier
+  \details Ensures the apparent order of the explicit memory operations before
+           and after the instruction, without ensuring their completion.
+ */
+__STATIC_FORCEINLINE  void __DMB(void)
+{
+  __ASM volatile ("dmb 0xF":::"memory");
+}
+
+/**
+  \brief   Reverse byte order (32 bit)
+  \details Reverses the byte order in unsigned integer value. For example, 0x12345678 becomes 0x78563412.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+__STATIC_FORCEINLINE  uint32_t __REV(uint32_t value)
+{
+#if (__GNUC__ > 4) || (__GNUC__ == 4 && __GNUC_MINOR__ >= 5)
+  return __builtin_bswap32(value);
+#else
+  uint32_t result;
+
+  __ASM volatile ("rev %0, %1" : __CMSIS_GCC_OUT_REG (result) : __CMSIS_GCC_USE_REG (value) );
+  return result;
+#endif
+}
+
+/**
+  \brief   Reverse byte order (16 bit)
+  \details Reverses the byte order within each halfword of a word. For example, 0x12345678 becomes 0x34127856.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".rev16_text"))) __STATIC_INLINE uint32_t __REV16(uint32_t value)
+{
+  uint32_t result;
+  __ASM volatile("rev16 %0, %1" : "=r" (result) : "r" (value));
+  return result;
+}
+#endif
+
+/**
+  \brief   Reverse byte order (16 bit)
+  \details Reverses the byte order in a 16-bit value and returns the signed 16-bit result. For example, 0x0080 becomes 0x8000.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+__STATIC_FORCEINLINE  int16_t __REVSH(int16_t value)
+{
+#if (__GNUC__ > 4) || (__GNUC__ == 4 && __GNUC_MINOR__ >= 8)
+  return (int16_t)__builtin_bswap16(value);
+#else
+  int16_t result;
+
+  __ASM volatile ("revsh %0, %1" : __CMSIS_GCC_OUT_REG (result) : __CMSIS_GCC_USE_REG (value) );
+  return result;
+#endif
+}
+
+/**
+  \brief   Rotate Right in unsigned value (32 bit)
+  \details Rotate Right (immediate) provides the value of the contents of a register rotated by a variable number of bits.
+  \param [in]    op1  Value to rotate
+  \param [in]    op2  Number of Bits to rotate
+  \return               Rotated value
+ */
+__STATIC_FORCEINLINE  uint32_t __ROR(uint32_t op1, uint32_t op2)
+{
+  op2 %= 32U;
+  if (op2 == 0U) {
+    return op1;
+  }
+  return (op1 >> op2) | (op1 << (32U - op2));
+}
+
+
+/**
+  \brief   Breakpoint
+  \param [in]    value  is ignored by the processor.
+                 If required, a debugger can use it to store additional information about the breakpoint.
+ */
+#define __BKPT(value)                       __ASM volatile ("bkpt "#value)
+
+/**
+  \brief   Reverse bit order of value
+  \details Reverses the bit order of the given value.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+__STATIC_FORCEINLINE  uint32_t __RBIT(uint32_t value)
+{
+  uint32_t result;
+
+#if ((defined (__ARM_ARCH_7M__      ) && (__ARM_ARCH_7M__      == 1)) || \
+     (defined (__ARM_ARCH_7EM__     ) && (__ARM_ARCH_7EM__     == 1)) || \
+     (defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1))    )
+   __ASM volatile ("rbit %0, %1" : "=r" (result) : "r" (value) );
+#else
+  int32_t s = (4U /*sizeof(v)*/ * 8U) - 1U; /* extra shift needed at end */
+
+  result = value;                      /* r will be reversed bits of v; first get LSB of v */
+  for (value >>= 1U; value; value >>= 1U)
+  {
+    result <<= 1U;
+    result |= value & 1U;
+    s--;
+  }
+  result <<= s;                        /* shift when v's highest bits are zero */
+#endif
+  return result;
+}
+
+/**
+  \brief   Count leading zeros
+  \param [in]  value  Value to count the leading zeros
+  \return             number of leading zeros in value
+ */
+#define __CLZ                             (uint8_t)__builtin_clz
+
+/**
+  \brief   LDR Exclusive (8 bit)
+  \details Executes a exclusive LDR instruction for 8 bit value.
+  \param [in]    ptr  Pointer to data
+  \return             value of type uint8_t at (*ptr)
+ */
+__STATIC_FORCEINLINE  uint8_t __LDREXB(volatile uint8_t *addr)
+{
+    uint32_t result;
+
+#if (__GNUC__ > 4) || (__GNUC__ == 4 && __GNUC_MINOR__ >= 8)
+   __ASM volatile ("ldrexb %0, %1" : "=r" (result) : "Q" (*addr) );
+#else
+    /* Prior to GCC 4.8, "Q" will be expanded to [rx, #0] which is not
+       accepted by assembler. So has to use following less efficient pattern.
+    */
+   __ASM volatile ("ldrexb %0, [%1]" : "=r" (result) : "r" (addr) : "memory" );
+#endif
+   return ((uint8_t) result);    /* Add explicit type cast here */
+}
+
+
+/**
+  \brief   LDR Exclusive (16 bit)
+  \details Executes a exclusive LDR instruction for 16 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint16_t at (*ptr)
+ */
+__STATIC_FORCEINLINE  uint16_t __LDREXH(volatile uint16_t *addr)
+{
+    uint32_t result;
+
+#if (__GNUC__ > 4) || (__GNUC__ == 4 && __GNUC_MINOR__ >= 8)
+   __ASM volatile ("ldrexh %0, %1" : "=r" (result) : "Q" (*addr) );
+#else
+    /* Prior to GCC 4.8, "Q" will be expanded to [rx, #0] which is not
+       accepted by assembler. So has to use following less efficient pattern.
+    */
+   __ASM volatile ("ldrexh %0, [%1]" : "=r" (result) : "r" (addr) : "memory" );
+#endif
+   return ((uint16_t) result);    /* Add explicit type cast here */
+}
+
+
+/**
+  \brief   LDR Exclusive (32 bit)
+  \details Executes a exclusive LDR instruction for 32 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint32_t at (*ptr)
+ */
+__STATIC_FORCEINLINE  uint32_t __LDREXW(volatile uint32_t *addr)
+{
+    uint32_t result;
+
+   __ASM volatile ("ldrex %0, %1" : "=r" (result) : "Q" (*addr) );
+   return(result);
+}
+
+
+/**
+  \brief   STR Exclusive (8 bit)
+  \details Executes a exclusive STR instruction for 8 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+__STATIC_FORCEINLINE  uint32_t __STREXB(uint8_t value, volatile uint8_t *addr)
+{
+   uint32_t result;
+
+   __ASM volatile ("strexb %0, %2, %1" : "=&r" (result), "=Q" (*addr) : "r" ((uint32_t)value) );
+   return(result);
+}
+
+
+/**
+  \brief   STR Exclusive (16 bit)
+  \details Executes a exclusive STR instruction for 16 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+__STATIC_FORCEINLINE  uint32_t __STREXH(uint16_t value, volatile uint16_t *addr)
+{
+   uint32_t result;
+
+   __ASM volatile ("strexh %0, %2, %1" : "=&r" (result), "=Q" (*addr) : "r" ((uint32_t)value) );
+   return(result);
+}
+
+
+/**
+  \brief   STR Exclusive (32 bit)
+  \details Executes a exclusive STR instruction for 32 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+__STATIC_FORCEINLINE  uint32_t __STREXW(uint32_t value, volatile uint32_t *addr)
+{
+   uint32_t result;
+
+   __ASM volatile ("strex %0, %2, %1" : "=&r" (result), "=Q" (*addr) : "r" (value) );
+   return(result);
+}
+
+
+/**
+  \brief   Remove the exclusive lock
+  \details Removes the exclusive lock which is created by LDREX.
+ */
+__STATIC_FORCEINLINE  void __CLREX(void)
+{
+  __ASM volatile ("clrex" ::: "memory");
+}
+
+/**
+  \brief   Signed Saturate
+  \details Saturates a signed value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (1..32)
+  \return             Saturated value
+ */
+#define __SSAT(ARG1,ARG2) \
+__extension__ \
+({                          \
+  int32_t __RES, __ARG1 = (ARG1); \
+  __ASM ("ssat %0, %1, %2" : "=r" (__RES) :  "I" (ARG2), "r" (__ARG1) ); \
+  __RES; \
+ })
+
+
+/**
+  \brief   Unsigned Saturate
+  \details Saturates an unsigned value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (0..31)
+  \return             Saturated value
+ */
+#define __USAT(ARG1,ARG2) \
+__extension__ \
+({                          \
+  uint32_t __RES, __ARG1 = (ARG1); \
+  __ASM ("usat %0, %1, %2" : "=r" (__RES) :  "I" (ARG2), "r" (__ARG1) ); \
+  __RES; \
+ })
+
+/* ###########################  Core Function Access  ########################### */
+
+/**
+  \brief   Enable IRQ Interrupts
+  \details Enables IRQ interrupts by clearing the I-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+__STATIC_FORCEINLINE void __enable_irq(void)
+{
+  __ASM volatile ("cpsie i" : : : "memory");
+}
+
+/**
+  \brief   Disable IRQ Interrupts
+  \details Disables IRQ interrupts by setting the I-bit in the CPSR.
+  Can only be executed in Privileged modes.
+ */
+__STATIC_FORCEINLINE  void __disable_irq(void)
+{
+  __ASM volatile ("cpsid i" : : : "memory");
+}
+
+/**
+  \brief   Get FPSCR
+  \details Returns the current value of the Floating Point Status/Control register.
+  \return Floating Point Status/Control register value
+*/
+__STATIC_FORCEINLINE  uint32_t __get_FPSCR(void)
+{
+  #if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+       (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+  #if __has_builtin(__builtin_arm_get_fpscr) 
+  // Re-enable using built-in when GCC has been fixed
+  // || (__GNUC__ > 7) || (__GNUC__ == 7 && __GNUC_MINOR__ >= 2)
+    /* see https://gcc.gnu.org/ml/gcc-patches/2017-04/msg00443.html */
+    return __builtin_arm_get_fpscr();
+  #else
+    uint32_t result;
+
+    __ASM volatile ("VMRS %0, fpscr" : "=r" (result) );
+    return(result);
+  #endif
+  #else
+    return(0U);
+  #endif
+}
+
+/**
+  \brief   Set FPSCR
+  \details Assigns the given value to the Floating Point Status/Control register.
+  \param [in] fpscr  Floating Point Status/Control value to set
+*/
+__STATIC_FORCEINLINE void __set_FPSCR(uint32_t fpscr)
+{
+  #if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+       (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+  #if __has_builtin(__builtin_arm_set_fpscr)
+  // Re-enable using built-in when GCC has been fixed
+  // || (__GNUC__ > 7) || (__GNUC__ == 7 && __GNUC_MINOR__ >= 2)
+    /* see https://gcc.gnu.org/ml/gcc-patches/2017-04/msg00443.html */
+    __builtin_arm_set_fpscr(fpscr);
+  #else
+    __ASM volatile ("VMSR fpscr, %0" : : "r" (fpscr) : "vfpcc", "memory");
+  #endif
+  #else
+    (void)fpscr;
+  #endif
+}
+
+/** \brief  Get CPSR Register
+    \return               CPSR Register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_CPSR(void)
+{
+  uint32_t result;
+  __ASM volatile("MRS %0, cpsr" : "=r" (result) );
+  return(result);
+}
+
+/** \brief  Set CPSR Register
+    \param [in]    cpsr  CPSR value to set
+ */
+__STATIC_FORCEINLINE void __set_CPSR(uint32_t cpsr)
+{
+__ASM volatile ("MSR cpsr, %0" : : "r" (cpsr) : "memory");
+}
+
+/** \brief  Get Mode
+    \return                Processor Mode
+ */
+__STATIC_FORCEINLINE uint32_t __get_mode(void)
+{
+    return (__get_CPSR() & 0x1FU);
+}
+
+/** \brief  Set Mode
+    \param [in]    mode  Mode value to set
+ */
+__STATIC_FORCEINLINE void __set_mode(uint32_t mode)
+{
+  __ASM volatile("MSR  cpsr_c, %0" : : "r" (mode) : "memory");
+}
+
+/** \brief  Get Stack Pointer
+    \return Stack Pointer value
+ */
+__STATIC_FORCEINLINE uint32_t __get_SP(void)
+{
+  uint32_t result;
+  __ASM volatile("MOV  %0, sp" : "=r" (result) : : "memory");
+  return result;
+}
+
+/** \brief  Set Stack Pointer
+    \param [in]    stack  Stack Pointer value to set
+ */
+__STATIC_FORCEINLINE void __set_SP(uint32_t stack)
+{
+  __ASM volatile("MOV  sp, %0" : : "r" (stack) : "memory");
+}
+
+/** \brief  Get USR/SYS Stack Pointer
+    \return USR/SYS Stack Pointer value
+ */
+__STATIC_FORCEINLINE uint32_t __get_SP_usr(void)
+{
+  uint32_t cpsr = __get_CPSR();
+  uint32_t result;
+  __ASM volatile(
+    "CPS     #0x1F  \n"
+    "MOV     %0, sp   " : "=r"(result) : : "memory"
+   );
+  __set_CPSR(cpsr);
+  __ISB();
+  return result;
+}
+
+/** \brief  Set USR/SYS Stack Pointer
+    \param [in]    topOfProcStack  USR/SYS Stack Pointer value to set
+ */
+__STATIC_FORCEINLINE void __set_SP_usr(uint32_t topOfProcStack)
+{
+  uint32_t cpsr = __get_CPSR();
+  __ASM volatile(
+    "CPS     #0x1F  \n"
+    "MOV     sp, %0   " : : "r" (topOfProcStack) : "memory"
+   );
+  __set_CPSR(cpsr);
+  __ISB();
+}
+
+/** \brief  Get FPEXC
+    \return               Floating Point Exception Control register value
+ */
+__STATIC_FORCEINLINE uint32_t __get_FPEXC(void)
+{
+#if (__FPU_PRESENT == 1)
+  uint32_t result;
+  __ASM volatile("VMRS %0, fpexc" : "=r" (result) );
+  return(result);
+#else
+  return(0);
+#endif
+}
+
+/** \brief  Set FPEXC
+    \param [in]    fpexc  Floating Point Exception Control value to set
+ */
+__STATIC_FORCEINLINE void __set_FPEXC(uint32_t fpexc)
+{
+#if (__FPU_PRESENT == 1)
+  __ASM volatile ("VMSR fpexc, %0" : : "r" (fpexc) : "memory");
+#endif
+}
+
+/*
+ * Include common core functions to access Coprocessor 15 registers
+ */
+
+#define __get_CP(cp, op1, Rt, CRn, CRm, op2) __ASM volatile("MRC p" # cp ", " # op1 ", %0, c" # CRn ", c" # CRm ", " # op2 : "=r" (Rt) : : "memory" )
+#define __set_CP(cp, op1, Rt, CRn, CRm, op2) __ASM volatile("MCR p" # cp ", " # op1 ", %0, c" # CRn ", c" # CRm ", " # op2 : : "r" (Rt) : "memory" )
+#define __get_CP64(cp, op1, Rt, CRm) __ASM volatile("MRRC p" # cp ", " # op1 ", %Q0, %R0, c" # CRm  : "=r" (Rt) : : "memory" )
+#define __set_CP64(cp, op1, Rt, CRm) __ASM volatile("MCRR p" # cp ", " # op1 ", %Q0, %R0, c" # CRm  : : "r" (Rt) : "memory" )
+
+#include "cmsis_cp15.h"
+
+/** \brief  Enable Floating Point Unit
+
+  Critical section, called from undef handler, so systick is disabled
+ */
+__STATIC_INLINE void __FPU_Enable(void)
+{
+  __ASM volatile(
+    //Permit access to VFP/NEON, registers by modifying CPACR
+    "        MRC     p15,0,R1,c1,c0,2  \n"
+    "        ORR     R1,R1,#0x00F00000 \n"
+    "        MCR     p15,0,R1,c1,c0,2  \n"
+
+    //Ensure that subsequent instructions occur in the context of VFP/NEON access permitted
+    "        ISB                       \n"
+
+    //Enable VFP/NEON
+    "        VMRS    R1,FPEXC          \n"
+    "        ORR     R1,R1,#0x40000000 \n"
+    "        VMSR    FPEXC,R1          \n"
+
+    //Initialise VFP/NEON registers to 0
+    "        MOV     R2,#0             \n"
+
+    //Initialise D16 registers to 0
+    "        VMOV    D0, R2,R2         \n"
+    "        VMOV    D1, R2,R2         \n"
+    "        VMOV    D2, R2,R2         \n"
+    "        VMOV    D3, R2,R2         \n"
+    "        VMOV    D4, R2,R2         \n"
+    "        VMOV    D5, R2,R2         \n"
+    "        VMOV    D6, R2,R2         \n"
+    "        VMOV    D7, R2,R2         \n"
+    "        VMOV    D8, R2,R2         \n"
+    "        VMOV    D9, R2,R2         \n"
+    "        VMOV    D10,R2,R2         \n"
+    "        VMOV    D11,R2,R2         \n"
+    "        VMOV    D12,R2,R2         \n"
+    "        VMOV    D13,R2,R2         \n"
+    "        VMOV    D14,R2,R2         \n"
+    "        VMOV    D15,R2,R2         \n"
+
+#if (defined(__ARM_NEON) && (__ARM_NEON == 1))
+    //Initialise D32 registers to 0
+    "        VMOV    D16,R2,R2         \n"
+    "        VMOV    D17,R2,R2         \n"
+    "        VMOV    D18,R2,R2         \n"
+    "        VMOV    D19,R2,R2         \n"
+    "        VMOV    D20,R2,R2         \n"
+    "        VMOV    D21,R2,R2         \n"
+    "        VMOV    D22,R2,R2         \n"
+    "        VMOV    D23,R2,R2         \n"
+    "        VMOV    D24,R2,R2         \n"
+    "        VMOV    D25,R2,R2         \n"
+    "        VMOV    D26,R2,R2         \n"
+    "        VMOV    D27,R2,R2         \n"
+    "        VMOV    D28,R2,R2         \n"
+    "        VMOV    D29,R2,R2         \n"
+    "        VMOV    D30,R2,R2         \n"
+    "        VMOV    D31,R2,R2         \n"
+#endif
+
+    //Initialise FPSCR to a known state
+    "        VMRS    R2,FPSCR          \n"
+    "        LDR     R3,=0x00086060    \n" //Mask off all bits that do not have to be preserved. Non-preserved bits can/should be zero.
+    "        AND     R2,R2,R3          \n"
+    "        VMSR    FPSCR,R2            "
+  );
+}
+
+#pragma GCC diagnostic pop
+
+#endif /* __CMSIS_GCC_H */

Drivers/CMSIS/Core_A/Include/cmsis_iccarm.h

@@ -0,0 +1,559 @@
+/**************************************************************************//**
+ * @file     cmsis_iccarm.h
+ * @brief    CMSIS compiler ICCARM (IAR Compiler for Arm) header file
+ * @version  V5.0.6
+ * @date     02. March 2018
+ ******************************************************************************/
+
+//------------------------------------------------------------------------------
+//
+// Copyright (c) 2017-2018 IAR Systems
+//
+// Licensed under the Apache License, Version 2.0 (the "License")
+// you may not use this file except in compliance with the License.
+// You may obtain a copy of the License at
+//     http://www.apache.org/licenses/LICENSE-2.0
+//
+// Unless required by applicable law or agreed to in writing, software
+// distributed under the License is distributed on an "AS IS" BASIS,
+// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+// See the License for the specific language governing permissions and
+// limitations under the License.
+//
+//------------------------------------------------------------------------------
+
+
+#ifndef __CMSIS_ICCARM_H__
+#define __CMSIS_ICCARM_H__
+
+#ifndef __ICCARM__
+  #error This file should only be compiled by ICCARM
+#endif
+
+#pragma system_include
+
+#define __IAR_FT _Pragma("inline=forced") __intrinsic
+
+#if (__VER__ >= 8000000)
+  #define __ICCARM_V8 1
+#else
+  #define __ICCARM_V8 0
+#endif
+
+#pragma language=extended
+
+#ifndef __ALIGNED
+  #if __ICCARM_V8
+    #define __ALIGNED(x) __attribute__((aligned(x)))
+  #elif (__VER__ >= 7080000)
+    /* Needs IAR language extensions */
+    #define __ALIGNED(x) __attribute__((aligned(x)))
+  #else
+    #warning No compiler specific solution for __ALIGNED.__ALIGNED is ignored.
+    #define __ALIGNED(x)
+  #endif
+#endif
+
+
+/* Define compiler macros for CPU architecture, used in CMSIS 5.
+ */
+#if __ARM_ARCH_7A__
+/* Macro already defined */
+#else
+  #if defined(__ARM7A__)
+    #define __ARM_ARCH_7A__ 1
+  #endif
+#endif
+
+#ifndef __ASM
+  #define __ASM __asm
+#endif
+
+#ifndef __INLINE
+  #define __INLINE inline
+#endif
+
+#ifndef   __NO_RETURN
+  #if __ICCARM_V8
+    #define __NO_RETURN __attribute__((__noreturn__))
+  #else
+    #define __NO_RETURN _Pragma("object_attribute=__noreturn")
+  #endif
+#endif
+
+#ifndef   __PACKED
+  /* Needs IAR language extensions */
+  #if __ICCARM_V8
+    #define __PACKED __attribute__((packed, aligned(1)))
+  #else
+    #define __PACKED __packed
+  #endif
+#endif
+
+#ifndef   __PACKED_STRUCT
+  /* Needs IAR language extensions */
+  #if __ICCARM_V8
+    #define __PACKED_STRUCT struct __attribute__((packed, aligned(1)))
+  #else
+    #define __PACKED_STRUCT __packed struct
+  #endif
+#endif
+
+#ifndef   __PACKED_UNION
+  /* Needs IAR language extensions */
+  #if __ICCARM_V8
+    #define __PACKED_UNION union __attribute__((packed, aligned(1)))
+  #else
+    #define __PACKED_UNION __packed union
+  #endif
+#endif
+
+#ifndef   __RESTRICT
+  #define __RESTRICT            __restrict
+#endif
+
+#ifndef   __STATIC_INLINE
+  #define __STATIC_INLINE       static inline
+#endif
+
+#ifndef   __FORCEINLINE
+  #define __FORCEINLINE         _Pragma("inline=forced")
+#endif
+
+#ifndef   __STATIC_FORCEINLINE
+  #define __STATIC_FORCEINLINE  __FORCEINLINE __STATIC_INLINE
+#endif
+
+#ifndef   CMSIS_DEPRECATED
+  #define CMSIS_DEPRECATED      __attribute__((deprecated))
+#endif
+
+#ifndef __UNALIGNED_UINT16_READ
+  #pragma language=save
+  #pragma language=extended
+  __IAR_FT uint16_t __iar_uint16_read(void const *ptr)
+  {
+    return *(__packed uint16_t*)(ptr);
+  }
+  #pragma language=restore
+  #define __UNALIGNED_UINT16_READ(PTR) __iar_uint16_read(PTR)
+#endif
+
+
+#ifndef __UNALIGNED_UINT16_WRITE
+  #pragma language=save
+  #pragma language=extended
+  __IAR_FT void __iar_uint16_write(void const *ptr, uint16_t val)
+  {
+    *(__packed uint16_t*)(ptr) = val;;
+  }
+  #pragma language=restore
+  #define __UNALIGNED_UINT16_WRITE(PTR,VAL) __iar_uint16_write(PTR,VAL)
+#endif
+
+#ifndef __UNALIGNED_UINT32_READ
+  #pragma language=save
+  #pragma language=extended
+  __IAR_FT uint32_t __iar_uint32_read(void const *ptr)
+  {
+    return *(__packed uint32_t*)(ptr);
+  }
+  #pragma language=restore
+  #define __UNALIGNED_UINT32_READ(PTR) __iar_uint32_read(PTR)
+#endif
+
+#ifndef __UNALIGNED_UINT32_WRITE
+  #pragma language=save
+  #pragma language=extended
+  __IAR_FT void __iar_uint32_write(void const *ptr, uint32_t val)
+  {
+    *(__packed uint32_t*)(ptr) = val;;
+  }
+  #pragma language=restore
+  #define __UNALIGNED_UINT32_WRITE(PTR,VAL) __iar_uint32_write(PTR,VAL)
+#endif
+
+#if 0
+#ifndef __UNALIGNED_UINT32   /* deprecated */
+  #pragma language=save
+  #pragma language=extended
+  __packed struct  __iar_u32 { uint32_t v; };
+  #pragma language=restore
+  #define __UNALIGNED_UINT32(PTR) (((struct __iar_u32 *)(PTR))->v)
+#endif
+#endif
+
+#ifndef   __USED
+  #if __ICCARM_V8
+    #define __USED __attribute__((used))
+  #else
+    #define __USED _Pragma("__root")
+  #endif
+#endif
+
+#ifndef   __WEAK
+  #if __ICCARM_V8
+    #define __WEAK __attribute__((weak))
+  #else
+    #define __WEAK _Pragma("__weak")
+  #endif
+#endif
+
+
+#ifndef __ICCARM_INTRINSICS_VERSION__
+  #define __ICCARM_INTRINSICS_VERSION__  0
+#endif
+
+#if __ICCARM_INTRINSICS_VERSION__ == 2
+
+  #if defined(__CLZ)
+    #undef __CLZ
+  #endif
+  #if defined(__REVSH)
+    #undef __REVSH
+  #endif
+  #if defined(__RBIT)
+    #undef __RBIT
+  #endif
+  #if defined(__SSAT)
+    #undef __SSAT
+  #endif
+  #if defined(__USAT)
+    #undef __USAT
+  #endif
+
+  #include "iccarm_builtin.h"
+
+  #define __enable_irq        __iar_builtin_enable_interrupt
+  #define __disable_irq       __iar_builtin_disable_interrupt
+  #define __enable_fault_irq    __iar_builtin_enable_fiq
+  #define __disable_fault_irq   __iar_builtin_disable_fiq
+  #define __arm_rsr           __iar_builtin_rsr
+  #define __arm_wsr           __iar_builtin_wsr
+
+  #if __FPU_PRESENT
+    #define __get_FPSCR()             (__arm_rsr("FPSCR"))
+  #else
+    #define __get_FPSCR()             ( 0 )
+  #endif
+
+  #define __set_FPSCR(VALUE)          (__arm_wsr("FPSCR", VALUE))
+
+  #define __get_CPSR()                (__arm_rsr("CPSR"))
+  #define __get_mode()                (__get_CPSR() & 0x1FU)
+
+  #define __set_CPSR(VALUE)           (__arm_wsr("CPSR", (VALUE)))
+  #define __set_mode(VALUE)           (__arm_wsr("CPSR_c", (VALUE)))
+
+
+  #define __get_FPEXC()       (__arm_rsr("FPEXC"))
+  #define __set_FPEXC(VALUE)    (__arm_wsr("FPEXC", VALUE))
+
+  #define __get_CP(cp, op1, RT, CRn, CRm, op2) \
+    ((RT) = __arm_rsr("p" # cp ":" # op1 ":c" # CRn ":c" # CRm ":" # op2))
+
+  #define __set_CP(cp, op1, RT, CRn, CRm, op2) \
+    (__arm_wsr("p" # cp ":" # op1 ":c" # CRn ":c" # CRm ":" # op2, (RT)))
+
+  #define __get_CP64(cp, op1, Rt, CRm) \
+    __ASM volatile("MRRC p" # cp ", " # op1 ", %Q0, %R0, c" # CRm  : "=r" (Rt) : : "memory" )
+
+  #define __set_CP64(cp, op1, Rt, CRm) \
+    __ASM volatile("MCRR p" # cp ", " # op1 ", %Q0, %R0, c" # CRm  : : "r" (Rt) : "memory" )
+
+  #include "cmsis_cp15.h"
+
+  #define __NOP     __iar_builtin_no_operation
+
+  #define __CLZ     __iar_builtin_CLZ
+  #define __CLREX   __iar_builtin_CLREX
+
+  #define __DMB     __iar_builtin_DMB
+  #define __DSB     __iar_builtin_DSB
+  #define __ISB     __iar_builtin_ISB
+
+  #define __LDREXB  __iar_builtin_LDREXB
+  #define __LDREXH  __iar_builtin_LDREXH
+  #define __LDREXW  __iar_builtin_LDREX
+
+  #define __RBIT    __iar_builtin_RBIT
+  #define __REV     __iar_builtin_REV
+  #define __REV16   __iar_builtin_REV16
+
+  __IAR_FT int16_t __REVSH(int16_t val)
+  {
+    return (int16_t) __iar_builtin_REVSH(val);
+  }
+
+  #define __ROR     __iar_builtin_ROR
+  #define __RRX     __iar_builtin_RRX
+
+  #define __SEV     __iar_builtin_SEV
+
+  #define __SSAT    __iar_builtin_SSAT
+
+  #define __STREXB  __iar_builtin_STREXB
+  #define __STREXH  __iar_builtin_STREXH
+  #define __STREXW  __iar_builtin_STREX
+
+  #define __USAT    __iar_builtin_USAT
+
+  #define __WFE     __iar_builtin_WFE
+  #define __WFI     __iar_builtin_WFI
+
+  #define __SADD8   __iar_builtin_SADD8
+  #define __QADD8   __iar_builtin_QADD8
+  #define __SHADD8  __iar_builtin_SHADD8
+  #define __UADD8   __iar_builtin_UADD8
+  #define __UQADD8  __iar_builtin_UQADD8
+  #define __UHADD8  __iar_builtin_UHADD8
+  #define __SSUB8   __iar_builtin_SSUB8
+  #define __QSUB8   __iar_builtin_QSUB8
+  #define __SHSUB8  __iar_builtin_SHSUB8
+  #define __USUB8   __iar_builtin_USUB8
+  #define __UQSUB8  __iar_builtin_UQSUB8
+  #define __UHSUB8  __iar_builtin_UHSUB8
+  #define __SADD16  __iar_builtin_SADD16
+  #define __QADD16  __iar_builtin_QADD16
+  #define __SHADD16 __iar_builtin_SHADD16
+  #define __UADD16  __iar_builtin_UADD16
+  #define __UQADD16 __iar_builtin_UQADD16
+  #define __UHADD16 __iar_builtin_UHADD16
+  #define __SSUB16  __iar_builtin_SSUB16
+  #define __QSUB16  __iar_builtin_QSUB16
+  #define __SHSUB16 __iar_builtin_SHSUB16
+  #define __USUB16  __iar_builtin_USUB16
+  #define __UQSUB16 __iar_builtin_UQSUB16
+  #define __UHSUB16 __iar_builtin_UHSUB16
+  #define __SASX    __iar_builtin_SASX
+  #define __QASX    __iar_builtin_QASX
+  #define __SHASX   __iar_builtin_SHASX
+  #define __UASX    __iar_builtin_UASX
+  #define __UQASX   __iar_builtin_UQASX
+  #define __UHASX   __iar_builtin_UHASX
+  #define __SSAX    __iar_builtin_SSAX
+  #define __QSAX    __iar_builtin_QSAX
+  #define __SHSAX   __iar_builtin_SHSAX
+  #define __USAX    __iar_builtin_USAX
+  #define __UQSAX   __iar_builtin_UQSAX
+  #define __UHSAX   __iar_builtin_UHSAX
+  #define __USAD8   __iar_builtin_USAD8
+  #define __USADA8  __iar_builtin_USADA8
+  #define __SSAT16  __iar_builtin_SSAT16
+  #define __USAT16  __iar_builtin_USAT16
+  #define __UXTB16  __iar_builtin_UXTB16
+  #define __UXTAB16 __iar_builtin_UXTAB16
+  #define __SXTB16  __iar_builtin_SXTB16
+  #define __SXTAB16 __iar_builtin_SXTAB16
+  #define __SMUAD   __iar_builtin_SMUAD
+  #define __SMUADX  __iar_builtin_SMUADX
+  #define __SMMLA   __iar_builtin_SMMLA
+  #define __SMLAD   __iar_builtin_SMLAD
+  #define __SMLADX  __iar_builtin_SMLADX
+  #define __SMLALD  __iar_builtin_SMLALD
+  #define __SMLALDX __iar_builtin_SMLALDX
+  #define __SMUSD   __iar_builtin_SMUSD
+  #define __SMUSDX  __iar_builtin_SMUSDX
+  #define __SMLSD   __iar_builtin_SMLSD
+  #define __SMLSDX  __iar_builtin_SMLSDX
+  #define __SMLSLD  __iar_builtin_SMLSLD
+  #define __SMLSLDX __iar_builtin_SMLSLDX
+  #define __SEL     __iar_builtin_SEL
+  #define __QADD    __iar_builtin_QADD
+  #define __QSUB    __iar_builtin_QSUB
+  #define __PKHBT   __iar_builtin_PKHBT
+  #define __PKHTB   __iar_builtin_PKHTB
+
+#else /* __ICCARM_INTRINSICS_VERSION__ == 2 */
+
+  #if !__FPU_PRESENT
+  #define __get_FPSCR __cmsis_iar_get_FPSR_not_active
+  #endif
+
+  #ifdef __INTRINSICS_INCLUDED
+  #error intrinsics.h is already included previously!
+  #endif
+
+  #include <intrinsics.h>
+
+  #if !__FPU_PRESENT
+  #define __get_FPSCR() (0)
+  #endif
+
+  #pragma diag_suppress=Pe940
+  #pragma diag_suppress=Pe177
+
+  #define __enable_irq        __enable_interrupt
+  #define __disable_irq       __disable_interrupt
+  #define __enable_fault_irq    __enable_fiq
+  #define __disable_fault_irq   __disable_fiq
+  #define __NOP               __no_operation
+
+  #define __get_xPSR          __get_PSR
+
+  __IAR_FT void __set_mode(uint32_t mode)
+  {
+    __ASM volatile("MSR  cpsr_c, %0" : : "r" (mode) : "memory");
+  }
+
+  __IAR_FT uint32_t __LDREXW(uint32_t volatile *ptr)
+  {
+    return __LDREX((unsigned long *)ptr);
+  }
+
+  __IAR_FT uint32_t __STREXW(uint32_t value, uint32_t volatile *ptr)
+  {
+    return __STREX(value, (unsigned long *)ptr);
+  }
+
+
+  __IAR_FT uint32_t __RRX(uint32_t value)
+  {
+    uint32_t result;
+    __ASM("RRX      %0, %1" : "=r"(result) : "r" (value) : "cc");
+    return(result);
+  }
+
+
+  __IAR_FT uint32_t __ROR(uint32_t op1, uint32_t op2)
+  {
+    return (op1 >> op2) | (op1 << ((sizeof(op1)*8)-op2));
+  }
+
+  __IAR_FT uint32_t __get_FPEXC(void)
+  {
+  #if (__FPU_PRESENT == 1)
+    uint32_t result;
+    __ASM volatile("VMRS %0, fpexc" : "=r" (result) : : "memory");
+    return(result);
+  #else
+    return(0);
+  #endif
+  }
+
+  __IAR_FT void __set_FPEXC(uint32_t fpexc)
+  {
+  #if (__FPU_PRESENT == 1)
+    __ASM volatile ("VMSR fpexc, %0" : : "r" (fpexc) : "memory");
+  #endif
+  }
+
+
+  #define __get_CP(cp, op1, Rt, CRn, CRm, op2) \
+    __ASM volatile("MRC p" # cp ", " # op1 ", %0, c" # CRn ", c" # CRm ", " # op2 : "=r" (Rt) : : "memory" )
+  #define __set_CP(cp, op1, Rt, CRn, CRm, op2) \
+    __ASM volatile("MCR p" # cp ", " # op1 ", %0, c" # CRn ", c" # CRm ", " # op2 : : "r" (Rt) : "memory" )
+  #define __get_CP64(cp, op1, Rt, CRm) \
+    __ASM volatile("MRRC p" # cp ", " # op1 ", %Q0, %R0, c" # CRm  : "=r" (Rt) : : "memory" )
+  #define __set_CP64(cp, op1, Rt, CRm) \
+    __ASM volatile("MCRR p" # cp ", " # op1 ", %Q0, %R0, c" # CRm  : : "r" (Rt) : "memory" )
+
+  #include "cmsis_cp15.h"
+
+#endif   /* __ICCARM_INTRINSICS_VERSION__ == 2 */
+
+#define __BKPT(value)    __asm volatile ("BKPT     %0" : : "i"(value))
+
+
+__IAR_FT uint32_t __get_SP_usr(void)
+{
+  uint32_t cpsr;
+  uint32_t result;
+  __ASM volatile(
+    "MRS     %0, cpsr   \n"
+    "CPS     #0x1F      \n" // no effect in USR mode
+    "MOV     %1, sp     \n"
+    "MSR     cpsr_c, %2 \n" // no effect in USR mode
+    "ISB" :  "=r"(cpsr), "=r"(result) : "r"(cpsr) : "memory"
+   );
+  return result;
+}
+
+__IAR_FT void __set_SP_usr(uint32_t topOfProcStack)
+{
+  uint32_t cpsr;
+  __ASM volatile(
+    "MRS     %0, cpsr   \n"
+    "CPS     #0x1F      \n" // no effect in USR mode
+    "MOV     sp, %1     \n"
+    "MSR     cpsr_c, %2 \n" // no effect in USR mode
+    "ISB" : "=r"(cpsr) : "r" (topOfProcStack), "r"(cpsr) : "memory"
+   );
+}
+
+#define __get_mode()                (__get_CPSR() & 0x1FU)
+
+__STATIC_INLINE
+void __FPU_Enable(void)
+{
+  __ASM volatile(
+    //Permit access to VFP/NEON, registers by modifying CPACR
+    "        MRC     p15,0,R1,c1,c0,2  \n"
+    "        ORR     R1,R1,#0x00F00000 \n"
+    "        MCR     p15,0,R1,c1,c0,2  \n"
+
+    //Ensure that subsequent instructions occur in the context of VFP/NEON access permitted
+    "        ISB                       \n"
+
+    //Enable VFP/NEON
+    "        VMRS    R1,FPEXC          \n"
+    "        ORR     R1,R1,#0x40000000 \n"
+    "        VMSR    FPEXC,R1          \n"
+
+    //Initialise VFP/NEON registers to 0
+    "        MOV     R2,#0             \n"
+
+    //Initialise D16 registers to 0
+    "        VMOV    D0, R2,R2         \n"
+    "        VMOV    D1, R2,R2         \n"
+    "        VMOV    D2, R2,R2         \n"
+    "        VMOV    D3, R2,R2         \n"
+    "        VMOV    D4, R2,R2         \n"
+    "        VMOV    D5, R2,R2         \n"
+    "        VMOV    D6, R2,R2         \n"
+    "        VMOV    D7, R2,R2         \n"
+    "        VMOV    D8, R2,R2         \n"
+    "        VMOV    D9, R2,R2         \n"
+    "        VMOV    D10,R2,R2         \n"
+    "        VMOV    D11,R2,R2         \n"
+    "        VMOV    D12,R2,R2         \n"
+    "        VMOV    D13,R2,R2         \n"
+    "        VMOV    D14,R2,R2         \n"
+    "        VMOV    D15,R2,R2         \n"
+
+#ifdef __ARM_ADVANCED_SIMD__
+    //Initialise D32 registers to 0
+    "        VMOV    D16,R2,R2         \n"
+    "        VMOV    D17,R2,R2         \n"
+    "        VMOV    D18,R2,R2         \n"
+    "        VMOV    D19,R2,R2         \n"
+    "        VMOV    D20,R2,R2         \n"
+    "        VMOV    D21,R2,R2         \n"
+    "        VMOV    D22,R2,R2         \n"
+    "        VMOV    D23,R2,R2         \n"
+    "        VMOV    D24,R2,R2         \n"
+    "        VMOV    D25,R2,R2         \n"
+    "        VMOV    D26,R2,R2         \n"
+    "        VMOV    D27,R2,R2         \n"
+    "        VMOV    D28,R2,R2         \n"
+    "        VMOV    D29,R2,R2         \n"
+    "        VMOV    D30,R2,R2         \n"
+    "        VMOV    D31,R2,R2         \n"
+#endif
+
+    //Initialise FPSCR to a known state
+    "        VMRS    R2,FPSCR          \n"
+    "        MOV32   R3,#0x00086060    \n" //Mask off all bits that do not have to be preserved. Non-preserved bits can/should be zero.
+    "        AND     R2,R2,R3          \n"
+    "        VMSR    FPSCR,R2          \n");
+}
+
+
+
+#undef __IAR_FT
+#undef __ICCARM_V8
+
+#pragma diag_default=Pe940
+#pragma diag_default=Pe177
+
+#endif /* __CMSIS_ICCARM_H__ */

Drivers/CMSIS/Core_A/Include/irq_ctrl.h

@@ -0,0 +1,186 @@
+/**************************************************************************//**
+ * @file     irq_ctrl.h
+ * @brief    Interrupt Controller API header file
+ * @version  V1.0.0
+ * @date     23. June 2017
+ ******************************************************************************/
+/*
+ * Copyright (c) 2017 ARM Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef IRQ_CTRL_H_
+#define IRQ_CTRL_H_
+
+#include <stdint.h>
+
+#ifndef IRQHANDLER_T
+#define IRQHANDLER_T
+/// Interrupt handler data type
+typedef void (*IRQHandler_t) (void);
+#endif
+
+#ifndef IRQN_ID_T
+#define IRQN_ID_T
+/// Interrupt ID number data type
+typedef int32_t IRQn_ID_t;
+#endif
+
+/* Interrupt mode bit-masks */
+#define IRQ_MODE_TRIG_Pos           (0U)
+#define IRQ_MODE_TRIG_Msk           (0x07UL /*<< IRQ_MODE_TRIG_Pos*/)
+#define IRQ_MODE_TRIG_LEVEL         (0x00UL /*<< IRQ_MODE_TRIG_Pos*/) ///< Trigger: level triggered interrupt
+#define IRQ_MODE_TRIG_LEVEL_LOW     (0x01UL /*<< IRQ_MODE_TRIG_Pos*/) ///< Trigger: low level triggered interrupt
+#define IRQ_MODE_TRIG_LEVEL_HIGH    (0x02UL /*<< IRQ_MODE_TRIG_Pos*/) ///< Trigger: high level triggered interrupt
+#define IRQ_MODE_TRIG_EDGE          (0x04UL /*<< IRQ_MODE_TRIG_Pos*/) ///< Trigger: edge triggered interrupt
+#define IRQ_MODE_TRIG_EDGE_RISING   (0x05UL /*<< IRQ_MODE_TRIG_Pos*/) ///< Trigger: rising edge triggered interrupt
+#define IRQ_MODE_TRIG_EDGE_FALLING  (0x06UL /*<< IRQ_MODE_TRIG_Pos*/) ///< Trigger: falling edge triggered interrupt
+#define IRQ_MODE_TRIG_EDGE_BOTH     (0x07UL /*<< IRQ_MODE_TRIG_Pos*/) ///< Trigger: rising and falling edge triggered interrupt
+
+#define IRQ_MODE_TYPE_Pos           (3U)
+#define IRQ_MODE_TYPE_Msk           (0x01UL << IRQ_MODE_TYPE_Pos)
+#define IRQ_MODE_TYPE_IRQ           (0x00UL << IRQ_MODE_TYPE_Pos)     ///< Type: interrupt source triggers CPU IRQ line
+#define IRQ_MODE_TYPE_FIQ           (0x01UL << IRQ_MODE_TYPE_Pos)     ///< Type: interrupt source triggers CPU FIQ line
+
+#define IRQ_MODE_DOMAIN_Pos         (4U)
+#define IRQ_MODE_DOMAIN_Msk         (0x01UL << IRQ_MODE_DOMAIN_Pos)
+#define IRQ_MODE_DOMAIN_NONSECURE   (0x00UL << IRQ_MODE_DOMAIN_Pos)   ///< Domain: interrupt is targeting non-secure domain
+#define IRQ_MODE_DOMAIN_SECURE      (0x01UL << IRQ_MODE_DOMAIN_Pos)   ///< Domain: interrupt is targeting secure domain
+
+#define IRQ_MODE_CPU_Pos            (5U)
+#define IRQ_MODE_CPU_Msk            (0xFFUL << IRQ_MODE_CPU_Pos)
+#define IRQ_MODE_CPU_ALL            (0x00UL << IRQ_MODE_CPU_Pos)      ///< CPU: interrupt targets all CPUs
+#define IRQ_MODE_CPU_0              (0x01UL << IRQ_MODE_CPU_Pos)      ///< CPU: interrupt targets CPU 0
+#define IRQ_MODE_CPU_1              (0x02UL << IRQ_MODE_CPU_Pos)      ///< CPU: interrupt targets CPU 1
+#define IRQ_MODE_CPU_2              (0x04UL << IRQ_MODE_CPU_Pos)      ///< CPU: interrupt targets CPU 2
+#define IRQ_MODE_CPU_3              (0x08UL << IRQ_MODE_CPU_Pos)      ///< CPU: interrupt targets CPU 3
+#define IRQ_MODE_CPU_4              (0x10UL << IRQ_MODE_CPU_Pos)      ///< CPU: interrupt targets CPU 4
+#define IRQ_MODE_CPU_5              (0x20UL << IRQ_MODE_CPU_Pos)      ///< CPU: interrupt targets CPU 5
+#define IRQ_MODE_CPU_6              (0x40UL << IRQ_MODE_CPU_Pos)      ///< CPU: interrupt targets CPU 6
+#define IRQ_MODE_CPU_7              (0x80UL << IRQ_MODE_CPU_Pos)      ///< CPU: interrupt targets CPU 7
+
+#define IRQ_MODE_ERROR              (0x80000000UL)                    ///< Bit indicating mode value error
+
+/* Interrupt priority bit-masks */
+#define IRQ_PRIORITY_Msk            (0x0000FFFFUL)                    ///< Interrupt priority value bit-mask
+#define IRQ_PRIORITY_ERROR          (0x80000000UL)                    ///< Bit indicating priority value error
+
+/// Initialize interrupt controller.
+/// \return 0 on success, -1 on error.
+int32_t IRQ_Initialize (void);
+
+/// Register interrupt handler.
+/// \param[in]     irqn          interrupt ID number
+/// \param[in]     handler       interrupt handler function address
+/// \return 0 on success, -1 on error.
+int32_t IRQ_SetHandler (IRQn_ID_t irqn, IRQHandler_t handler);
+
+/// Get the registered interrupt handler.
+/// \param[in]     irqn          interrupt ID number
+/// \return registered interrupt handler function address.
+IRQHandler_t IRQ_GetHandler (IRQn_ID_t irqn);
+
+/// Enable interrupt.
+/// \param[in]     irqn          interrupt ID number
+/// \return 0 on success, -1 on error.
+int32_t IRQ_Enable (IRQn_ID_t irqn);
+
+/// Disable interrupt.
+/// \param[in]     irqn          interrupt ID number
+/// \return 0 on success, -1 on error.
+int32_t IRQ_Disable (IRQn_ID_t irqn);
+
+/// Get interrupt enable state.
+/// \param[in]     irqn          interrupt ID number
+/// \return 0 - interrupt is disabled, 1 - interrupt is enabled.
+uint32_t IRQ_GetEnableState (IRQn_ID_t irqn);
+
+/// Configure interrupt request mode.
+/// \param[in]     irqn          interrupt ID number
+/// \param[in]     mode          mode configuration
+/// \return 0 on success, -1 on error.
+int32_t IRQ_SetMode (IRQn_ID_t irqn, uint32_t mode);
+
+/// Get interrupt mode configuration.
+/// \param[in]     irqn          interrupt ID number
+/// \return current interrupt mode configuration with optional IRQ_MODE_ERROR bit set.
+uint32_t IRQ_GetMode (IRQn_ID_t irqn);
+
+/// Get ID number of current interrupt request (IRQ).
+/// \return interrupt ID number.
+IRQn_ID_t IRQ_GetActiveIRQ (void);
+
+/// Get ID number of current fast interrupt request (FIQ).
+/// \return interrupt ID number.
+IRQn_ID_t IRQ_GetActiveFIQ (void);
+
+/// Signal end of interrupt processing.
+/// \param[in]     irqn          interrupt ID number
+/// \return 0 on success, -1 on error.
+int32_t IRQ_EndOfInterrupt (IRQn_ID_t irqn);
+
+/// Set interrupt pending flag.
+/// \param[in]     irqn          interrupt ID number
+/// \return 0 on success, -1 on error.
+int32_t IRQ_SetPending (IRQn_ID_t irqn);
+
+/// Get interrupt pending flag.
+/// \param[in]     irqn          interrupt ID number
+/// \return 0 - interrupt is not pending, 1 - interrupt is pending.
+uint32_t IRQ_GetPending (IRQn_ID_t irqn);
+
+/// Clear interrupt pending flag.
+/// \param[in]     irqn          interrupt ID number
+/// \return 0 on success, -1 on error.
+int32_t IRQ_ClearPending (IRQn_ID_t irqn);
+
+/// Set interrupt priority value.
+/// \param[in]     irqn          interrupt ID number
+/// \param[in]     priority      interrupt priority value
+/// \return 0 on success, -1 on error.
+int32_t IRQ_SetPriority (IRQn_ID_t irqn, uint32_t priority);
+
+/// Get interrupt priority.
+/// \param[in]     irqn          interrupt ID number
+/// \return current interrupt priority value with optional IRQ_PRIORITY_ERROR bit set.
+uint32_t IRQ_GetPriority (IRQn_ID_t irqn);
+
+/// Set priority masking threshold.
+/// \param[in]     priority      priority masking threshold value
+/// \return 0 on success, -1 on error.
+int32_t IRQ_SetPriorityMask (uint32_t priority);
+
+/// Get priority masking threshold
+/// \return current priority masking threshold value with optional IRQ_PRIORITY_ERROR bit set.
+uint32_t IRQ_GetPriorityMask (void);
+
+/// Set priority grouping field split point
+/// \param[in]     bits          number of MSB bits included in the group priority field comparison
+/// \return 0 on success, -1 on error.
+int32_t IRQ_SetPriorityGroupBits (uint32_t bits);
+
+/// Get priority grouping field split point
+/// \return current number of MSB bits included in the group priority field comparison with
+///         optional IRQ_PRIORITY_ERROR bit set.
+uint32_t IRQ_GetPriorityGroupBits (void);
+
+#endif  // IRQ_CTRL_H_

Drivers/CMSIS/Core_A/Source/irq_ctrl_gic.c

@@ -0,0 +1,410 @@
+/**************************************************************************//**
+ * @file     irq_ctrl_gic.c
+ * @brief    Interrupt controller handling implementation for GIC
+ * @version  V1.0.1
+ * @date     9. April 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2017 ARM Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#include <stddef.h>
+
+#include "RTE_Components.h"
+#include CMSIS_device_header
+
+#include "irq_ctrl.h"
+
+#if defined(__GIC_PRESENT) && (__GIC_PRESENT == 1U)
+
+/// Number of implemented interrupt lines
+#ifndef IRQ_GIC_LINE_COUNT
+#define IRQ_GIC_LINE_COUNT      (1020U)
+#endif
+
+static IRQHandler_t IRQTable[IRQ_GIC_LINE_COUNT] = { 0U };
+static uint32_t     IRQ_ID0;
+
+/// Initialize interrupt controller.
+__WEAK int32_t IRQ_Initialize (void) {
+  uint32_t i;
+
+  for (i = 0U; i < IRQ_GIC_LINE_COUNT; i++) {
+    IRQTable[i] = (IRQHandler_t)NULL;
+  }
+  GIC_Enable();
+  return (0);
+}
+
+
+/// Register interrupt handler.
+__WEAK int32_t IRQ_SetHandler (IRQn_ID_t irqn, IRQHandler_t handler) {
+  int32_t status;
+
+  if ((irqn >= 0) && (irqn < (IRQn_ID_t)IRQ_GIC_LINE_COUNT)) {
+    IRQTable[irqn] = handler;
+    status =  0;
+  } else {
+    status = -1;
+  }
+
+  return (status);
+}
+
+
+/// Get the registered interrupt handler.
+__WEAK IRQHandler_t IRQ_GetHandler (IRQn_ID_t irqn) {
+  IRQHandler_t h;
+
+  // Ignore CPUID field (software generated interrupts)
+  irqn &= 0x3FFU;
+
+  if ((irqn >= 0) && (irqn < (IRQn_ID_t)IRQ_GIC_LINE_COUNT)) {
+    h = IRQTable[irqn];
+  } else {
+    h = (IRQHandler_t)0;
+  }
+
+  return (h);
+}
+
+
+/// Enable interrupt.
+__WEAK int32_t IRQ_Enable (IRQn_ID_t irqn) {
+  int32_t status;
+
+  if ((irqn >= 0) && (irqn < (IRQn_ID_t)IRQ_GIC_LINE_COUNT)) {
+    GIC_EnableIRQ ((IRQn_Type)irqn);
+    status = 0;
+  } else {
+    status = -1;
+  }
+
+  return (status);
+}
+
+
+/// Disable interrupt.
+__WEAK int32_t IRQ_Disable (IRQn_ID_t irqn) {
+  int32_t status;
+
+  if ((irqn >= 0) && (irqn < (IRQn_ID_t)IRQ_GIC_LINE_COUNT)) {
+    GIC_DisableIRQ ((IRQn_Type)irqn);
+    status = 0;
+  } else {
+    status = -1;
+  }
+
+  return (status);
+}
+
+
+/// Get interrupt enable state.
+__WEAK uint32_t IRQ_GetEnableState (IRQn_ID_t irqn) {
+  uint32_t enable;
+
+  if ((irqn >= 0) && (irqn < (IRQn_ID_t)IRQ_GIC_LINE_COUNT)) {
+    enable = GIC_GetEnableIRQ((IRQn_Type)irqn);
+  } else {
+    enable = 0U;
+  }
+
+  return (enable);
+}
+
+
+/// Configure interrupt request mode.
+__WEAK int32_t IRQ_SetMode (IRQn_ID_t irqn, uint32_t mode) {
+  uint32_t val;
+  uint8_t cfg;
+  uint8_t secure;
+  uint8_t cpu;
+  int32_t status = 0;
+
+  if ((irqn >= 0) && (irqn < (IRQn_ID_t)IRQ_GIC_LINE_COUNT)) {
+    // Check triggering mode
+    val = (mode & IRQ_MODE_TRIG_Msk);
+
+    if (val == IRQ_MODE_TRIG_LEVEL) {
+      cfg = 0x00U;
+    } else if (val == IRQ_MODE_TRIG_EDGE) {
+      cfg = 0x02U;
+    } else {
+      cfg = 0x00U;
+      status = -1;
+    }
+
+    // Check interrupt type
+    val = mode & IRQ_MODE_TYPE_Msk;
+
+    if (val != IRQ_MODE_TYPE_IRQ) {
+      status = -1;
+    }
+
+    // Check interrupt domain
+    val = mode & IRQ_MODE_DOMAIN_Msk;
+
+    if (val == IRQ_MODE_DOMAIN_NONSECURE) {
+      secure = 0U;
+    } else {
+      // Check security extensions support
+      val = GIC_DistributorInfo() & (1UL << 10U);
+
+      if (val != 0U) {
+        // Security extensions are supported
+        secure = 1U;
+      } else {
+        secure = 0U;
+        status = -1;
+      }
+    }
+
+    // Check interrupt CPU targets
+    val = mode & IRQ_MODE_CPU_Msk;
+
+    if (val == IRQ_MODE_CPU_ALL) {
+      cpu = 0xFFU;
+    } else {
+      cpu = val >> IRQ_MODE_CPU_Pos;
+    }
+
+    // Apply configuration if no mode error
+    if (status == 0) {
+      GIC_SetConfiguration((IRQn_Type)irqn, cfg);
+      GIC_SetTarget       ((IRQn_Type)irqn, cpu);
+
+      if (secure != 0U) {
+        GIC_SetGroup ((IRQn_Type)irqn, secure);
+      }
+    }
+  }
+
+  return (status);
+}
+
+
+/// Get interrupt mode configuration.
+__WEAK uint32_t IRQ_GetMode (IRQn_ID_t irqn) {
+  uint32_t mode;
+  uint32_t val;
+
+  if ((irqn >= 0) && (irqn < (IRQn_ID_t)IRQ_GIC_LINE_COUNT)) {
+    mode = IRQ_MODE_TYPE_IRQ;
+
+    // Get trigger mode
+    val = GIC_GetConfiguration((IRQn_Type)irqn);
+
+    if ((val & 2U) != 0U) {
+      // Corresponding interrupt is edge triggered
+      mode |= IRQ_MODE_TRIG_EDGE;
+    } else {
+      // Corresponding interrupt is level triggered
+      mode |= IRQ_MODE_TRIG_LEVEL;
+    }
+
+    // Get interrupt CPU targets
+    mode |= GIC_GetTarget ((IRQn_Type)irqn) << IRQ_MODE_CPU_Pos;
+
+  } else {
+    mode = IRQ_MODE_ERROR;
+  }
+
+  return (mode);
+}
+
+
+/// Get ID number of current interrupt request (IRQ).
+__WEAK IRQn_ID_t IRQ_GetActiveIRQ (void) {
+  IRQn_ID_t irqn;
+  uint32_t prio;
+
+  /* Dummy read to avoid GIC 390 errata 801120 */
+  GIC_GetHighPendingIRQ();
+
+  irqn = GIC_AcknowledgePending();
+
+  __DSB();
+
+  /* Workaround GIC 390 errata 733075 (GIC-390_Errata_Notice_v6.pdf, 09-Jul-2014)  */
+  /* The following workaround code is for a single-core system.  It would be       */
+  /* different in a multi-core system.                                             */
+  /* If the ID is 0 or 0x3FE or 0x3FF, then the GIC CPU interface may be locked-up */
+  /* so unlock it, otherwise service the interrupt as normal.                      */
+  /* Special IDs 1020=0x3FC and 1021=0x3FD are reserved values in GICv1 and GICv2  */
+  /* so will not occur here.                                                       */
+
+  if ((irqn == 0) || (irqn >= 0x3FE)) {
+    /* Unlock the CPU interface with a dummy write to Interrupt Priority Register */
+    prio = GIC_GetPriority((IRQn_Type)0);
+    GIC_SetPriority ((IRQn_Type)0, prio);
+
+    __DSB();
+
+    if ((irqn == 0U) && ((GIC_GetIRQStatus ((IRQn_Type)irqn) & 1U) != 0U) && (IRQ_ID0 == 0U)) {
+      /* If the ID is 0, is active and has not been seen before */
+      IRQ_ID0 = 1U;
+    }
+    /* End of Workaround GIC 390 errata 733075 */
+  }
+
+  return (irqn);
+}
+
+
+/// Get ID number of current fast interrupt request (FIQ).
+__WEAK IRQn_ID_t IRQ_GetActiveFIQ (void) {
+  return ((IRQn_ID_t)-1);
+}
+
+
+/// Signal end of interrupt processing.
+__WEAK int32_t IRQ_EndOfInterrupt (IRQn_ID_t irqn) {
+  int32_t status;
+  IRQn_Type irq = (IRQn_Type)irqn;
+
+  irqn &= 0x3FFU;
+
+  if ((irqn >= 0) && (irqn < (IRQn_ID_t)IRQ_GIC_LINE_COUNT)) {
+    GIC_EndInterrupt (irq);
+
+    if (irqn == 0) {
+      IRQ_ID0 = 0U;
+    }
+
+    status = 0;
+  } else {
+    status = -1;
+  }
+
+  return (status);
+}
+
+
+/// Set interrupt pending flag.
+__WEAK int32_t IRQ_SetPending (IRQn_ID_t irqn) {
+  int32_t status;
+
+  if ((irqn >= 0) && (irqn < (IRQn_ID_t)IRQ_GIC_LINE_COUNT)) {
+    GIC_SetPendingIRQ ((IRQn_Type)irqn);
+    status = 0;
+  } else {
+    status = -1;
+  }
+
+  return (status);
+}
+
+/// Get interrupt pending flag.
+__WEAK uint32_t IRQ_GetPending (IRQn_ID_t irqn) {
+  uint32_t pending;
+
+  if ((irqn >= 16) && (irqn < (IRQn_ID_t)IRQ_GIC_LINE_COUNT)) {
+    pending = GIC_GetPendingIRQ ((IRQn_Type)irqn);
+  } else {
+    pending = 0U;
+  }
+
+  return (pending & 1U);
+}
+
+
+/// Clear interrupt pending flag.
+__WEAK int32_t IRQ_ClearPending (IRQn_ID_t irqn) {
+  int32_t status;
+
+  if ((irqn >= 16) && (irqn < (IRQn_ID_t)IRQ_GIC_LINE_COUNT)) {
+    GIC_ClearPendingIRQ ((IRQn_Type)irqn);
+    status = 0;
+  } else {
+    status = -1;
+  }
+
+  return (status);
+}
+
+
+/// Set interrupt priority value.
+__WEAK int32_t IRQ_SetPriority (IRQn_ID_t irqn, uint32_t priority) {
+  int32_t status;
+
+  if ((irqn >= 0) && (irqn < (IRQn_ID_t)IRQ_GIC_LINE_COUNT)) {
+    GIC_SetPriority ((IRQn_Type)irqn, priority);
+    status = 0;
+  } else {
+    status = -1;
+  }
+
+  return (status);
+}
+
+
+/// Get interrupt priority.
+__WEAK uint32_t IRQ_GetPriority (IRQn_ID_t irqn) {
+  uint32_t priority;
+
+  if ((irqn >= 0) && (irqn < (IRQn_ID_t)IRQ_GIC_LINE_COUNT)) {
+    priority = GIC_GetPriority ((IRQn_Type)irqn);
+  } else {
+    priority = IRQ_PRIORITY_ERROR;
+  }
+
+  return (priority);
+}
+
+
+/// Set priority masking threshold.
+__WEAK int32_t IRQ_SetPriorityMask (uint32_t priority) {
+  GIC_SetInterfacePriorityMask (priority);
+  return (0);
+}
+
+
+/// Get priority masking threshold
+__WEAK uint32_t IRQ_GetPriorityMask (void) {
+  return GIC_GetInterfacePriorityMask();
+}
+
+
+/// Set priority grouping field split point
+__WEAK int32_t IRQ_SetPriorityGroupBits (uint32_t bits) {
+  int32_t status;
+
+  if (bits == IRQ_PRIORITY_Msk) {
+    bits = 7U;
+  }
+
+  if (bits < 8U) {
+    GIC_SetBinaryPoint (7U - bits);
+    status = 0;
+  } else {
+    status = -1;
+  }
+
+  return (status);
+}
+
+
+/// Get priority grouping field split point
+__WEAK uint32_t IRQ_GetPriorityGroupBits (void) {
+  uint32_t bp;
+
+  bp = GIC_GetBinaryPoint() & 0x07U;
+
+  return (7U - bp);
+}
+
+#endif

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/arr_desc/arr_desc.h

@@ -0,0 +1,220 @@
+#ifndef _ARR_DESC_H_
+#define _ARR_DESC_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+#include <stdint.h>
+#include <string.h>             /* memset() */
+#include "../util/util.h"       /* CONCAT() */
+
+/*--------------------------------------------------------------------------------*/
+/* Type Definitions */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Array-descriptor struct.
+ */
+typedef struct ARR_DESC_struct
+{
+    void *  data_ptr;                /* Pointer to the array contents. */
+    int32_t element_count;           /* Number of current elements. */
+    int32_t element_size;            /* Size of current elements in bytes. */
+    int32_t underlying_size;         /* Size of underlying array in bytes. */
+} ARR_DESC_t;
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Prefix of the array variable's name when creating an array and an array
+ *  descriptor at the same time.
+ */
+#define ARR_DESC_ARR_PREFIX ARR_DESC_ARR_
+
+/**
+ *  Evaluate to the array variable's name when creating an array and an array
+ *  descriptor at the same time.
+ */
+#define ARR_DESC_ARR_NAME(name)                 \
+    CONCAT(ARR_DESC_ARR_PREFIX, name)
+
+/**
+ *  Define an #ARR_DESC_t by itself.
+ *
+ *  @note The user must supply an array to store the data used by the
+ *  #ARR_DESC_t.
+ */
+#define ARR_DESC_INTERNAL_DEFINE(name, data_ptr,                \
+                                 element_count, element_size)   \
+    ARR_DESC_t name = {                                         \
+        data_ptr,                                               \
+        element_count,                                          \
+        element_size,                                           \
+        element_count * element_size                            \
+    }                                                           \
+
+/**
+ *  Define both an array and an #ARR_DESC_t that describes it.
+ *
+ *  @note Use the #CURLY() macro for the content field; it provides the curly
+ *  braces necessary for an array initialization.
+ */
+#define ARR_DESC_DEFINE(type, name, element_count, content)             \
+    type ARR_DESC_ARR_NAME(name)[element_count] = content;              \
+    ARR_DESC_INTERNAL_DEFINE(name,                                      \
+                             &ARR_DESC_ARR_NAME(name),                  \
+                             element_count,                             \
+                             sizeof(type)) /* Note the lacking semicolon */
+
+/**
+ *  Create a #ARR_DESC_t which refers to a subset of the data in another.
+ *
+ *  The new #ARR_DESC_t shares the same underlying array as the aliased
+ *  #ARR_DESC_t, but only describes a subset of the originals values.
+ */
+#define ARR_DESC_DEFINE_SUBSET(name, original, element_cnt)         \
+    ARR_DESC_INTERNAL_DEFINE(name,                                  \
+                             &ARR_DESC_ARR_NAME(original),          \
+                             element_cnt,                           \
+                             sizeof(ARR_DESC_ARR_NAME(original)[0]) \
+        ) /* Note the lacking semicolon */
+
+/**
+ *  Creat an #ARR_DESC_t which points to the data in an existing array.
+ *
+ *  @param start_idx Offset in array_ptr of first element.
+ *  @param element_cnt Number of elements to include in the #ARR_DESC_t.
+ *
+ *  @example
+ *
+ *  float my_floats[4] = {0.0f, 1.0f, 2.0f, 3.0f};
+ *
+ *  ARR_DESC_DEFINE_USING_ARR(my_arr_desc, my_floats, 1, 3);
+ *
+ *  printf("Element 0: %f\n", ARR_DESC_ELT(float, 0, &my_arr_desc));
+ *  printf("Element 1: %f\n", ARR_DESC_ELT(float, 1, &my_arr_desc));
+ *
+ *  Outputs:
+ *
+ *  Element 0: 1.000000
+ *  Element 1: 2.000000
+ *
+ *  @warning There are no checks in place to catch invalid start indices; This
+ *  is left to the user.
+ */
+#define ARR_DESC_DEFINE_USING_ARR(type, name, array_ptr, start_idx, element_cnt) \
+    ARR_DESC_INTERNAL_DEFINE(                                           \
+        name,                                                           \
+        (type *) (array_ptr + start_idx),                               \
+        element_cnt,                                                    \
+        sizeof(type)                                                    \
+        ) /* Note the lacking semicolon*/
+
+/**
+ *  Declare an #ARR_DESC_t object.
+ */
+#define ARR_DESC_DECLARE(name)                              \
+    extern ARR_DESC_t name /* Note the lacking semicolon */
+
+/**
+ *  Evaluate to the number of bytes stored in the #ARR_DESC_t.
+ */
+#define ARR_DESC_BYTES(arr_desc_ptr)                                \
+    ((arr_desc_ptr)->element_count * (arr_desc_ptr)->element_size)
+
+/**
+ *  Set the contents of #ARR_DESC_t to value.
+ */
+#define ARR_DESC_MEMSET(arr_desc_ptr, value, bytes)     \
+    do                                                  \
+    {                                                   \
+        memset((arr_desc_ptr)->data_ptr,                \
+               value,                                   \
+               BOUND(0,                                 \
+                     (arr_desc_ptr)->underlying_size,   \
+                     bytes)                             \
+            );                                          \
+    } while (0)
+
+/**
+ *  Perform a memcpy of 'bytes' bytes from the source #ARR_DESC_t to the
+ *  destination #ARR_DESC_t.
+ */
+#define ARR_DESC_MEMCPY(arr_desc_dest_ptr, arr_desc_src_ptr, bytes) \
+    do                                                              \
+    {                                                               \
+        memcpy((arr_desc_dest_ptr)->data_ptr,                       \
+               (arr_desc_src_ptr)->data_ptr,                        \
+               BOUND(0,                                             \
+                     (arr_desc_dest_ptr)->underlying_size,          \
+                     bytes));                                       \
+    } while (0)
+
+/**
+ *  Evaluate to true if the source #ARR_DESC_t contents will fit into the
+ *  destination #ARR_DESC_t and false otherwise.
+ */
+#define ARR_DESC_COPYABLE(arr_desc_dest_ptr, arr_desc_src_ptr)  \
+      (ARR_DESC_BYTES(arr_desc_src_ptr) <=                      \
+       (arr_desc_dest_ptr)->underlying_size)
+
+/**
+ *  Copy all the data from the source #ARR_DESC_t to the destination
+ *  #ARR_DESC_t.
+ *
+ *  @note If the destination #ARR_DESC_t is too small to fit the source data the
+ *  copy is aborted and nothing happens.
+ */
+#define ARR_DESC_COPY(arr_desc_dest_ptr, arr_desc_src_ptr)      \
+    do                                                          \
+    {                                                           \
+        if (ARR_DESC_COPYABLE(arr_desc_dest_ptr,                 \
+                             arr_desc_src_ptr))                 \
+        {                                                       \
+            ARR_DESC_MEMCPY(arr_desc_dest_ptr,                  \
+                            arr_desc_src_ptr,                   \
+                            ARR_DESC_BYTES(arr_desc_src_ptr));  \
+            /* Update the properties*/                          \
+            (arr_desc_dest_ptr)->element_count =                \
+                (arr_desc_src_ptr)->element_count;              \
+            (arr_desc_dest_ptr)->element_size =                 \
+                (arr_desc_src_ptr)->element_size;               \
+        }                                                       \
+    } while (0)
+
+/**
+ *  Compare the data in two #ARR_DESC_t structs for the specified number of
+ *  bytes.
+ */
+#define ARR_DESC_MEMCMP(arr_desc_ptr_a, arr_desc_ptr_b, bytes)  \
+        memcmp((arr_desc_ptr_a)->data_ptr,                      \
+            (arr_desc_ptr_b)->data_ptr,                         \
+               bytes) /* Note the lacking semicolon */          \
+
+/**
+ *  Zero out the contents of the #ARR_DESC_t.
+ */
+#define ARR_DESC_ZERO(arr_desc_ptr)             \
+        ARR_DESC_MEMSET(arr_desc_ptr,           \
+                        0,                      \
+                        (arr_desc_ptr)->underlying_size)
+
+/**
+ *  Evaluate to the data address in #ARR_DESC_t at offset.
+ */
+#define ARR_DESC_DATA_ADDR(type, arr_desc_ptr, offset)  \
+        ((void*)(((type *)                              \
+                  ((arr_desc_ptr)->data_ptr))           \
+                 + offset))
+
+/**
+ *  Evaluate to the element in #ARR_DESC_t with type at idx.
+ */
+#define ARR_DESC_ELT(type, idx, arr_desc_ptr)           \
+        (*((type *) ARR_DESC_DATA_ADDR(type,            \
+                                       arr_desc_ptr,    \
+                                       idx)))
+
+#endif /* _ARR_DESC_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/jtest.h

@@ -0,0 +1,17 @@
+#ifndef _JTEST_H_
+#define _JTEST_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+
+#include "jtest_fw.h"
+#include "jtest_test.h"
+#include "jtest_test_define.h"
+#include "jtest_test_call.h"
+#include "jtest_group.h"
+#include "jtest_group_define.h"
+#include "jtest_group_call.h"
+#include "jtest_cycle.h"
+
+#endif /* _JTEST_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/jtest_cycle.h

@@ -0,0 +1,65 @@
+#ifndef _JTEST_CYCLE_H_
+#define _JTEST_CYCLE_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+
+#include "jtest_fw.h"           /* JTEST_DUMP_STRF() */
+#include "jtest_systick.h"
+#include "jtest_util.h"         /* STR() */
+
+/*--------------------------------------------------------------------------------*/
+/* Declare Module Variables */
+/*--------------------------------------------------------------------------------*/
+extern const char * JTEST_CYCLE_STRF;
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Wrap the function call, fn_call, to count execution cycles and display the
+ *  results.
+ */
+/* skipp function name + param
+#define JTEST_COUNT_CYCLES(fn_call)                     \
+    do                                                  \
+    {                                                   \
+        uint32_t __jtest_cycle_end_count;               \
+                                                        \
+        JTEST_SYSTICK_RESET(SysTick);                   \
+        JTEST_SYSTICK_START(SysTick);                   \
+                                                        \
+        fn_call;                                        \
+                                                        \
+        __jtest_cycle_end_count =                       \
+            JTEST_SYSTICK_VALUE(SysTick);               \
+                                                        \
+		JTEST_SYSTICK_RESET(SysTick);                   \
+        JTEST_DUMP_STRF(JTEST_CYCLE_STRF,               \
+                        STR(fn_call),                   \
+                        (JTEST_SYSTICK_INITIAL_VALUE -  \
+                         __jtest_cycle_end_count));     \
+    } while (0)
+*/
+#define JTEST_COUNT_CYCLES(fn_call)                     \
+    do                                                  \
+    {                                                   \
+        uint32_t __jtest_cycle_end_count;               \
+                                                        \
+        JTEST_SYSTICK_RESET(SysTick);                   \
+        JTEST_SYSTICK_START(SysTick);                   \
+                                                        \
+        fn_call;                                        \
+                                                        \
+        __jtest_cycle_end_count =                       \
+            JTEST_SYSTICK_VALUE(SysTick);               \
+                                                        \
+		JTEST_SYSTICK_RESET(SysTick);                   \
+        JTEST_DUMP_STRF(JTEST_CYCLE_STRF,               \
+                        (JTEST_SYSTICK_INITIAL_VALUE -  \
+                         __jtest_cycle_end_count));     \
+    } while (0)
+
+#endif /* _JTEST_CYCLE_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/jtest_define.h

@@ -0,0 +1,37 @@
+#ifndef _JTEST_DEFINE_H_
+#define _JTEST_DEFINE_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Makes a symbol for use as a struct name. Names made this way have two parts;
+ *  the first parts is a prefix common to all structs of that class. The second
+ *  is a specifier which differs for each instance of that struct type.
+ */
+#define JTEST_STRUCT_NAME(prefix, specifier)    \
+    CONCAT(prefix, specifier)
+
+/**
+ *  Define a struct with type with a name generated by #JTEST_STRUCT_NAME().
+ */
+#define JTEST_DEFINE_STRUCT(type, struct_name)    \
+    type struct_name
+
+/**
+ *  Declare a struct with type with a name generated by #JTEST_STRUCT_NAME().
+ */
+#define JTEST_DECLARE_STRUCT(struct_definition) \
+    extern struct_definition
+
+/**
+ *  Define and initialize a struct (created with JTEST_DEFINE_STRUCT()) and
+ *  initialize it with init_values.
+ */
+#define JTEST_INIT_STRUCT(struct_definition, init_values)       \
+    struct_definition = {                                       \
+        init_values                                             \
+    }
+
+#endif /* _JTEST_DEFINE_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/jtest_fw.h

@@ -0,0 +1,253 @@
+#ifndef _JTEST_FW_H_
+#define _JTEST_FW_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+
+#include <stdint.h>             /* int32_t */
+#include <string.h>             /* strcpy() */
+#include <stdio.h>              /* sprintf() */
+#include "jtest_pf.h"           /* Extend JTEST_FW_t with Pass/Fail data */
+#include "jtest_group.h"
+
+/*--------------------------------------------------------------------------------*/
+/* Type Definitions */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  A struct used to interface with the Keil Debugger.
+ */
+typedef struct JTEST_FW_struct
+{
+    /* Action Triggers: The Keil debugger monitors these values for changes.  In
+     * response to a change, the debugger executes code on the host. */
+    volatile int32_t test_start;
+    volatile int32_t test_end;
+    volatile int32_t group_start;
+    volatile int32_t group_end;
+    volatile int32_t dump_str;
+    volatile int32_t dump_data;
+    volatile int32_t exit_fw;
+
+    JTEST_GROUP_t * current_group_ptr;
+
+    /* Buffers: The C-code cannot send strings and data directly to the
+     * debugging framework. Instead, the debugger can be told to read 128 byte
+     * (by default) chunks of memory.  Data received in this manner requires
+     * post-processing to be legible.*/
+    char * str_buffer;
+    char * data_buffer;
+
+    /* Pass/Fail Data */
+    JTEST_PF_MEMBERS;
+
+} JTEST_FW_t;
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Default name for the JTEST_FW struct.
+ *
+ *  Define your own if you want the variable containing the #JTEST_FW_t to have
+ *  a different name.
+ */
+#ifndef JTEST_FW
+#define JTEST_FW JTEST_FW
+#endif
+
+/**
+ *  Default name for the JTEST_FW_STR_BUFFER.
+ *
+ *  Define your own if you want the variable containing the char buffer to have
+ *  a different name.
+ */
+#ifndef JTEST_FW_STR_BUFFER
+#define JTEST_FW_STR_BUFFER JTEST_FW_STR_BUFFER
+#endif
+
+/**
+ *  Size of the #JTEST_FW_t, output string-buffer.
+ *
+ *  If you change this value, make sure the "dump_str_fn" and "dump_data_fn"
+ *  functions in jtest_fns.ini uses the same size. If you aren't sure, read the
+ *  documentation Keil Debugger Command 'DISPLAY'.
+ */
+#define JTEST_BUF_SIZE 256
+
+
+/**
+ *  The maximum number of bytes output at once using #JTEST_DUMP_STRF().
+ */
+#define JTEST_STR_MAX_OUTPUT_SIZE 128
+
+/**
+ *  The maximum number of block transimissions needed to send a string from a
+ *  buffer with JTEST_BUF_SIZE.
+ */
+#define JTEST_STR_MAX_OUTPUT_SEGMENTS           \
+    (JTEST_BUF_SIZE / JTEST_STR_MAX_OUTPUT_SIZE)
+
+/**
+ *  Initialize the JTEST framework.
+ */
+#define JTEST_INIT()                                                    \
+    do                                                                  \
+    {                                                                   \
+        JTEST_FW.str_buffer = JTEST_FW_STR_BUFFER;                      \
+    } while (0)
+
+/* Debugger Action-triggering Macros */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Dispatch macro to trigger various actions in the Keil Debugger.
+ */
+#define JTEST_TRIGGER_ACTION(action_name)       \
+    do                                          \
+    {                                           \
+        action_name();                          \
+    } while (0)
+
+/**
+ *  Trigger the "Test Start" action in the Keil Debugger.
+ */
+#define JTEST_ACT_TEST_START()                  \
+    JTEST_TRIGGER_ACTION(test_start)
+
+/**
+ *  Trigger the "Test End" action in the Keil Debugger.
+ */
+#define JTEST_ACT_TEST_END()                    \
+    JTEST_TRIGGER_ACTION(test_end)
+
+
+/**
+ *  Trigger the "Group Start" action in the Keil Debugger.
+ */
+#define JTEST_ACT_GROUP_START()                 \
+    JTEST_TRIGGER_ACTION(group_start)
+
+/**
+ *  Trigger the "Group End" action in the Keil Debugger.
+ */
+#define JTEST_ACT_GROUP_END()                   \
+    JTEST_TRIGGER_ACTION(group_end)
+
+
+/**
+ *  Fill the buffer named buf_name with value and dump it to the Keil debugger
+ *  using action.
+ */
+#define JTEST_ACT_DUMP(action, buf_name, value) \
+    do                                          \
+    {                                           \
+        JTEST_CLEAR_BUFFER(buf_name);           \
+        strcpy(JTEST_FW.buf_name, (value));     \
+        JTEST_TRIGGER_ACTION(action);           \
+    } while (0)
+
+/**
+ *  Trigger the "Exit Framework" action in the Keil Debugger.
+ */
+#define JTEST_ACT_EXIT_FW()                     \
+    do                                          \
+    {                                           \
+        JTEST_TRIGGER_ACTION(exit_fw);          \
+    } while (0)
+
+
+/* Buffer Manipulation Macros */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Clear the JTEST_FW buffer with name buf_name.
+ */
+#define JTEST_CLEAR_BUFFER(buf_name)                    \
+    do                                                  \
+    {                                                   \
+        memset(JTEST_FW.buf_name, 0, JTEST_BUF_SIZE);   \
+    } while (0)
+
+/**
+ *  Clear the memory needed for the JTEST_FW's string buffer.
+ */
+#define JTEST_CLEAR_STR_BUFFER()                \
+        JTEST_CLEAR_BUFFER(str_buffer)
+
+/**
+ *  Clear the memory needed for the JTEST_FW's data buffer.
+ */
+#define JTEST_CLEAR_DATA_BUFFER()               \
+        JTEST_CLEAR_BUFFER(data_buffer)
+
+/**
+ *  Dump the given string to the Keil Debugger.
+ */
+#define JTEST_DUMP_STR(string)                          \
+        JTEST_ACT_DUMP(dump_str, str_buffer, string)
+
+/**
+ *  Dump a formatted string to the Keil Debugger.
+ */
+#define JTEST_DUMP_STRF(format_str, ... )                               \
+    do                                                                  \
+    {                                                                   \
+        JTEST_CLEAR_STR_BUFFER();                                       \
+        sprintf(JTEST_FW.str_buffer,format_str, __VA_ARGS__);           \
+        jtest_dump_str_segments();                                      \
+    } while (0)
+
+/* Pass/Fail Macros */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Increment the number of passed tests in #JTEST_FW.
+ */
+#define JTEST_FW_INC_PASSED(amount)             \
+        JTEST_PF_INC_PASSED(&JTEST_FW, amount)
+
+/**
+ *  Increment the number of passed tests in #JTEST_FW.
+ */
+#define JTEST_FW_INC_FAILED(amount)             \
+        JTEST_PF_INC_FAILED(&JTEST_FW, amount)
+
+/* Manipulating the Current Group */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Evaluate to the current_group_ptr in #JTEST_FW.
+ */
+#define JTEST_CURRENT_GROUP_PTR()               \
+    (JTEST_FW.current_group_ptr)
+
+#define JTEST_SET_CURRENT_GROUP(group_ptr)      \
+    do                                          \
+    {                                           \
+        JTEST_CURRENT_GROUP_PTR() = group_ptr;  \
+    } while (0)
+
+/*--------------------------------------------------------------------------------*/
+/* Declare Global Variables */
+/*--------------------------------------------------------------------------------*/
+extern char JTEST_FW_STR_BUFFER[JTEST_BUF_SIZE];
+extern volatile JTEST_FW_t JTEST_FW;
+
+/*--------------------------------------------------------------------------------*/
+/* Function Prototypes */
+/*--------------------------------------------------------------------------------*/
+void jtest_dump_str_segments(void);
+
+void test_start  (void);
+void test_end    (void);
+void group_start (void);
+void group_end   (void);
+void dump_str    (void);
+void dump_data   (void);
+void exit_fw     (void);
+
+
+#endif /* _JTEST_FW_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/jtest_group.h

@@ -0,0 +1,66 @@
+#ifndef _JTEST_GROUP_H_
+#define _JTEST_GROUP_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+
+#include "jtest_pf.h"
+#include "jtest_util.h"
+
+/*--------------------------------------------------------------------------------*/
+/* Type Definitions */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  A struct which represents a group of #JTEST_TEST_t structs. This struct is
+ *  used to run the group of tests, and report on their outcomes.
+ */
+typedef struct JTEST_GROUP_struct
+{
+    void (* group_fn_ptr) (void); /**< Pointer to the test group */
+    char * name_str;              /**< Name of the group */
+    
+    /* Extend the #JTEST_GROUP_t with Pass/Fail information.*/
+    JTEST_PF_MEMBERS;
+} JTEST_GROUP_t;
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Set the name of JTEST_GROUP_t.
+ */
+#define JTEST_GROUP_SET_NAME(group_ptr, name)     \
+    JTEST_SET_STRUCT_ATTRIBUTE(group_ptr, name_str, name)
+
+#define JTEST_GROUP_SET_FN(group_ptr, fn_ptr)     \
+    JTEST_SET_STRUCT_ATTRIBUTE(group_ptr, group_fn_ptr, fn_ptr)
+
+/**
+ *  Increment the number of tests passed in the JTEST_GROUP_t pointed to by
+ *  group_ptr.
+ */
+#define JTEST_GROUP_INC_PASSED(group_ptr, amount) \
+    JTEST_PF_INC_PASSED(group_ptr, amount)
+
+/**
+ *  Increment the number of tests failed in the JTEST_GROUP_t pointed to by
+ *  group_ptr.
+ */
+#define JTEST_GROUP_INC_FAILED(group_ptr, amount) \
+    JTEST_PF_INC_FAILED(group_ptr, amount)
+
+/**
+ *  Reset the pass/fail information of the #JTEST_GROUP_t pointed to by
+ *  group_ptr.
+ */
+#define JTEST_GROUP_RESET_PF(group_ptr)         \
+    do                                          \
+    {                                           \
+        JTEST_PF_RESET_PASSED(group_ptr);       \
+        JTEST_PF_RESET_FAILED(group_ptr);       \
+    } while (0)
+
+#endif /* _JTEST_GROUP_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/jtest_group_call.h

@@ -0,0 +1,126 @@
+#ifndef _JTEST_GROUP_CALL_H_
+#define _JTEST_GROUP_CALL_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+
+#include "jtest_fw.h"
+#include <inttypes.h>
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Execute the test in the #JTEST_GROUP_t struct associated witht he identifier
+ *  group_fn.
+ */
+#define JTEST_GROUP_RUN(group_fn)                                   \
+    do                                                              \
+    {                                                               \
+        JTEST_DUMP_STR("Group Name:\n");                            \
+        JTEST_DUMP_STR(JTEST_GROUP_STRUCT_NAME(group_fn).name_str); \
+        JTEST_GROUP_STRUCT_NAME(group_fn).group_fn_ptr();           \
+    } while (0)
+
+
+/**
+ *  Update the enclosing #JTEST_GROUP_t's pass/fail information using the
+ *  current #JTEST_GROUP_t's.
+ *
+ *  @param group_ptr Pointer to the current #JTEST_GROUP_t.
+ *  @param parent_ptr Pointer to the enclosing #JTEST_GROUP_t.
+ *
+ *  @warning Only run this if the current #JTEST_GROUP_t is being called within
+ *  the context of another #JTEST_GROUP_t.
+ */
+#define JTEST_GROUP_UPDATE_PARENT_GROUP_PF(group_ptr, parent_group_ptr) \
+    do                                                                  \
+    {                                                                   \
+        JTEST_GROUP_INC_PASSED(parent_group_ptr,                        \
+                               (group_ptr)->passed);                    \
+        JTEST_GROUP_INC_FAILED(parent_group_ptr,                        \
+                               (group_ptr)->failed);                    \
+    } while (0)
+
+/**
+ *  Update the #JTEST_FW's pass/fail information using the current
+ *  #JTEST_GROUP_t's.
+ */
+#define JTEST_GROUP_UPDATE_FW_PF(group_ptr)                     \
+    do                                                          \
+    {                                                           \
+        JTEST_FW_INC_PASSED((group_ptr)->passed);               \
+        JTEST_FW_INC_FAILED((group_ptr)->failed);               \
+    } while (0)
+
+/**
+ *  Update the enclosing context with the current #JTEST_GROUP_t's pass/fail
+ *  information. If this group isn't in an enclosing group, it updates the
+ *  #JTEST_FW's pass/fail info by default.
+ */
+#define JTEST_GROUP_UPDATE_PARENT_GROUP_OR_FW_PF(group_ptr,         \
+                                                 parent_group_ptr)  \
+    do                                                              \
+    {                                                               \
+        /* Update the pass fail counts in the parent group */       \
+        if (parent_group_ptr /* Null implies Top*/)                 \
+        {                                                           \
+            JTEST_GROUP_UPDATE_PARENT_GROUP_PF(                     \
+                group_ptr,                                          \
+                parent_group_ptr);                                  \
+        } else {                                                    \
+            JTEST_GROUP_UPDATE_FW_PF(                               \
+                group_ptr);                                         \
+        }                                                           \
+    } while (0)
+
+/**
+ *  Dump the results of running the #JTEST_GROUP_t to the Keil Debugger.
+ */
+#define JTEST_GROUP_DUMP_RESULTS(group_ptr)                             \
+        do                                                              \
+        {                                                               \
+            JTEST_DUMP_STRF(                                            \
+                "Tests Run: %" PRIu32 "\n"                              \
+                "----------\n"                                          \
+                "   Passed: %" PRIu32 "\n"                              \
+                "   Failed: %" PRIu32 "\n",                             \
+                (group_ptr)->passed + (group_ptr)->failed,              \
+                (group_ptr)->passed,                                    \
+                (group_ptr)->failed);                                   \
+        } while (0)
+
+/**
+ *  Call the #JTEST_GROUP_t associated with the identifier group_fn.
+ */
+#define JTEST_GROUP_CALL(group_fn)                                      \
+        do                                                              \
+        {   /* Save the current group from JTEST_FW_t before swapping */ \
+            /* it to this group (in order to restore it later )*/       \
+            JTEST_GROUP_t * __jtest_temp_group_ptr =                    \
+                JTEST_CURRENT_GROUP_PTR();                              \
+            JTEST_SET_CURRENT_GROUP(&JTEST_GROUP_STRUCT_NAME(group_fn)); \
+                                                                        \
+            /* Reset this group's pass/fail count. Each group */        \
+            /* should only remember counts for its last execution. */   \
+            JTEST_GROUP_RESET_PF(JTEST_CURRENT_GROUP_PTR());            \
+                                                                        \
+            /* Run the current group */                                 \
+            JTEST_ACT_GROUP_START();                                    \
+            JTEST_GROUP_RUN(group_fn);                                  \
+            JTEST_ACT_GROUP_END();                                      \
+                                                                        \
+            /* Update the pass fail counts in the parent group (or FW) */ \
+            JTEST_GROUP_UPDATE_PARENT_GROUP_OR_FW_PF(                   \
+                JTEST_CURRENT_GROUP_PTR(),                              \
+                __jtest_temp_group_ptr);                                \
+                                                                        \
+            JTEST_GROUP_DUMP_RESULTS(JTEST_CURRENT_GROUP_PTR());        \
+                                                                        \
+            /* Restore the previously current group */                  \
+            JTEST_SET_CURRENT_GROUP(__jtest_temp_group_ptr);            \
+        } while (0)
+
+#endif /* _JTEST_GROUP_CALL_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/jtest_group_define.h

@@ -0,0 +1,87 @@
+#ifndef _JTEST_GROUP_DEFINE_H_
+#define _JTEST_GROUP_DEFINE_H_
+
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+
+#include "jtest_util.h"
+#include "jtest_define.h"
+#include "jtest_group.h"
+
+/* For defining macros with optional arguments */
+#include "opt_arg/opt_arg.h"
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Prefix for all #JTEST_GROUP_t structs.
+ */
+#define JTEST_GROUP_STRUCT_NAME_PREFIX G_JTEST_GROUP_STRUCT_
+
+/**
+ *  Define test template used by #JTEST_GROUP_t tests.
+ */
+#define JTEST_GROUP_FN_TEMPLATE(group_fn)    \
+    void group_fn(void)
+
+#define JTEST_GROUP_FN_PROTOTYPE JTEST_GROUP_FN_TEMPLATE /**< Alias for
+                                                            #JTEST_GROUP_FN_TEMPLATE. */
+
+/**
+ *  Evaluate to the name of the #JTEST_GROUP_t struct associated with group_fn.
+ */
+#define JTEST_GROUP_STRUCT_NAME(group_fn)    \
+    JTEST_STRUCT_NAME(JTEST_GROUP_STRUCT_NAME_PREFIX, group_fn)
+
+/**
+ *  Define a #JTEST_GROUP_t struct based on the given group_fn.
+ */
+#define JTEST_GROUP_DEFINE_STRUCT(group_fn)  \
+    JTEST_DEFINE_STRUCT(JTEST_GROUP_t,       \
+                        JTEST_GROUP_STRUCT_NAME(group_fn))
+
+/**
+ *  Declare a #JTEST_GROUP_t struct based on the given group_fn.
+ */
+#define JTEST_GROUP_DECLARE_STRUCT(group_fn) \
+    JTEST_DECLARE_STRUCT(JTEST_GROUP_DEFINE_STRUCT(group_fn))
+
+/**
+ *  Contents needed to initialize a JTEST_GROUP_t struct.
+ */
+#define JTEST_GROUP_STRUCT_INIT(group_fn)    \
+    group_fn,                                \
+        STR_NL(group_fn),                       \
+        JTEST_PF_MEMBER_INIT
+
+/**
+ *  Initialize the contents of a #JTEST_GROUP_t struct.
+ */
+#define JTEST_GROUP_INIT(group_fn)           \
+    JTEST_GROUP_DEFINE_STRUCT(group_fn) = {  \
+        JTEST_GROUP_STRUCT_INIT(group_fn)    \
+    }
+
+/* Test Definition Macro */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Define a #JTEST_GROUP_t object and a test function.
+ */
+#define JTEST_DEFINE_GROUP(group_fn)         \
+    JTEST_GROUP_FN_PROTOTYPE(group_fn);      \
+    JTEST_GROUP_INIT(group_fn);              \
+    JTEST_GROUP_FN_PROTOTYPE(group_fn) /* Notice the lacking semicolon */
+
+/**
+ *  Declare a #JTEST_GROUP_t object and a test function prototype.
+ */
+#define JTEST_DECLARE_GROUP(group_fn)        \
+    JTEST_GROUP_FN_PROTOTYPE(group_fn);      \
+    JTEST_GROUP_DECLARE_STRUCT(group_fn) /* Note the lacking semicolon */
+
+#endif /* _JTEST_GROUP_DEFINE_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/jtest_pf.h

@@ -0,0 +1,85 @@
+#ifndef _JTEST_PF_H_
+#define _JTEST_PF_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Purpose */
+/*--------------------------------------------------------------------------------*/
+/* jtest_pf.h Contains macros useful for capturing pass/fail data. */
+
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ * Members that can be added to other structs to extend them pass/fail data and
+ * corresponding functionality.
+ */
+#define JTEST_PF_MEMBERS                            \
+    uint32_t passed;                                \
+    uint32_t failed /* Note the lacking semicolon*/ \
+
+/**
+ *  Used for initializing JTEST_PF_MEMBERS in a struct declaration.
+ */
+#define JTEST_PF_MEMBER_INIT                    \
+    0,                                          \
+    0
+
+/* Member-Incrementing Macros */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Dispatch macro for incrementing #JTEST_PF_MEMBERS.
+ *
+ *  @param xxx Values: 'passed', 'failed'
+ */
+#define JTEST_PF_INC_XXX(xxx, struct_pf_ptr, amount)    \
+    do                                                  \
+    {                                                   \
+        ((struct_pf_ptr)->xxx) += (amount);             \
+    } while (0)
+
+/**
+ *  Specialization of the #JTEST_PF_INC_XXX macro to increment the passed
+ *  member.
+ */
+#define JTEST_PF_INC_PASSED(struct_pf_ptr, amount)  \
+    JTEST_PF_INC_XXX(passed, struct_pf_ptr, amount)
+
+
+/**
+ *  Specialization of the #JTEST_PF_INC_XXX macro to increment the failed
+ *  member.
+ */
+#define JTEST_PF_INC_FAILED(struct_pf_ptr, amount)  \
+    JTEST_PF_INC_XXX(failed, struct_pf_ptr, amount)
+
+
+/* Member-Resetting Macros */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Dispatch macro for setting #JTEST_PF_MEMBERS to zero.
+ *
+ *  @param xxx Values: 'passed', 'failed'
+ */
+#define JTEST_PF_RESET_XXX(xxx, struct_pf_ptr)  \
+    do                                          \
+    {                                           \
+        ((struct_pf_ptr)->xxx) = UINT32_C(0);   \
+    } while (0)
+
+/**
+ *  Specialization of #JTEST_PF_RESET_XXX for the 'passed' member.
+ */
+#define JTEST_PF_RESET_PASSED(struct_pf_ptr)    \
+    JTEST_PF_RESET_XXX(passed, struct_pf_ptr)
+
+/**
+ *  Specialization of #JTEST_PF_RESET_XXX for the 'failed' member.
+ */
+#define JTEST_PF_RESET_FAILED(struct_pf_ptr)    \
+    JTEST_PF_RESET_XXX(failed, struct_pf_ptr)
+
+#endif /* _JTEST_PF_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/jtest_systick.h

@@ -0,0 +1,93 @@
+#ifndef _JTEST_SYSTICK_H_
+#define _JTEST_SYSTICK_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+
+/* Get access to the SysTick structure. */
+#if   defined ARMCM0
+  #include "ARMCM0.h"
+#elif defined ARMCM0P
+  #include "ARMCM0plus.h"
+#elif defined ARMCM3
+  #include "ARMCM3.h"
+#elif defined ARMCM4
+  #include "ARMCM4.h"
+#elif defined ARMCM4_FP
+  #include "ARMCM4_FP.h"
+#elif defined ARMCM7
+  #include "ARMCM7.h" 
+#elif defined ARMCM7_SP
+  #include "ARMCM7_SP.h"
+#elif defined ARMCM7_DP
+  #include "ARMCM7_DP.h"
+#elif defined ARMSC000
+  #include "ARMSC000.h"
+#elif defined ARMSC300
+  #include "ARMSC300.h"
+#elif defined ARMv8MBL
+  #include "ARMv8MBL.h"
+#elif defined ARMv8MML
+  #include "ARMv8MML.h"
+#elif defined ARMv8MML_DSP
+  #include "ARMv8MML_DSP.h"
+#elif defined ARMv8MML_SP
+  #include "ARMv8MML_SP.h"
+#elif defined ARMv8MML_DSP_SP
+  #include "ARMv8MML_DSP_SP.h"
+#elif defined ARMv8MML_DP
+  #include "ARMv8MML_DP.h"
+#elif defined ARMv8MML_DSP_DP
+  #include "ARMv8MML_DSP_DP.h"
+
+#else
+  #warning "no appropriate header file found!"
+#endif
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Initial value for the SysTick module.
+ *
+ *  @note This is also the maximum value, important as SysTick is a decrementing
+ *  counter.
+ */
+#define JTEST_SYSTICK_INITIAL_VALUE 0xFFFFFF
+
+/**
+ *  Reset the SysTick, decrementing timer to it's maximum value and disable it.
+ *
+ *  This macro should leave the SysTick timer in a state that's ready for cycle
+ *  counting.
+ */
+#define JTEST_SYSTICK_RESET(systick_ptr)                    \
+    do                                                      \
+    {                                                       \
+        (systick_ptr)->LOAD = JTEST_SYSTICK_INITIAL_VALUE;  \
+        (systick_ptr)->VAL = 1;                             \
+                                                            \
+        /* Disable the SysTick module. */                   \
+        (systick_ptr)->CTRL = UINT32_C(0x000000);           \
+    } while (0)
+
+/**
+ *  Start the SysTick timer, sourced by the processor clock.
+ */
+#define JTEST_SYSTICK_START(systick_ptr)                    \
+    do                                                      \
+    {                                                       \
+        (systick_ptr)->CTRL =                               \
+            SysTick_CTRL_ENABLE_Msk |                       \
+            SysTick_CTRL_CLKSOURCE_Msk; /* Internal clk*/   \
+    } while (0)
+
+/**
+ *  Evaluate to the current value of the SysTick timer.
+ */
+#define JTEST_SYSTICK_VALUE(systick_ptr)        \
+    ((systick_ptr)->VAL)
+           
+#endif /* _JTEST_SYSTICK_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/jtest_test.h

@@ -0,0 +1,100 @@
+#ifndef _JTEST_TEST_H_
+#define _JTEST_TEST_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+
+#include <stdint.h>
+#include "jtest_util.h"
+#include "jtest_test_ret.h"
+
+/*--------------------------------------------------------------------------------*/
+/* Type Definitions */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  A struct which represents a Test in the JTEST framework.  This struct is
+ *  used to enable, run, and describe the test it represents.
+ */
+typedef struct JTEST_TEST_struct
+{
+    JTEST_TEST_RET_t ( * test_fn_ptr)(void); /**< Pointer to the test function. */
+    char   * test_fn_str;                    /**< Name of the test function */
+    char   * fut_str;           /**< Name of the function under test. */
+
+    /**
+     *  Flags that govern how the #JTEST_TEST_t behaves.
+     */
+    union {
+        struct {
+            unsigned enabled : 1;
+            unsigned unused  : 7;
+        } bits;
+        uint8_t byte;           /* Access all flags at once. */
+    } flags;
+    
+} JTEST_TEST_t;
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Assign a test function to the #JTEST_TEST_t struct.
+ */
+#define JTEST_TEST_SET_FN(jtest_test_ptr, fn_ptr)                   \
+    JTEST_SET_STRUCT_ATTRIBUTE(jtest_test_ptr, test_fn_ptr, fn_ptr)
+
+/**
+ *  Specify a function under test (FUT) for the #JTEST_TEST_t struct.
+ */
+#define JTEST_TEST_SET_FUT(jtest_test_ptr, str)                 \
+    JTEST_SET_STRUCT_ATTRIBUTE(jtest_test_ptr, fut_str, str)
+
+/* Macros concerning JTEST_TEST_t flags */
+/*--------------------------------------------------------------------------------*/
+
+#define JTEST_TEST_FLAG_SET 1 /**< Value of a set #JTEST_TEST_t flag. */
+#define JTEST_TEST_FLAG_CLR 0 /**< Value of a cleared #JTEST_TEST_t flag. */
+
+/**
+ *  Evaluate to the flag in #JTEST_TEST_t having flag_name.
+ */
+#define JTEST_TEST_FLAG(jtest_test_ptr, flag_name)  \
+    ((jtest_test_ptr)->flags.bits.flag_name)
+
+/**
+ *  Dispatch macro for setting and clearing #JTEST_TEST_t flags.
+ *
+ *  @param jtest_test_ptr Pointer to a #JTEST_TEST_t struct.
+ *  @param flag_name      Name of the flag to set in #JTEST_TEST_t.flags.bits
+ *  @param xxx            Vaid values: "SET" or "CLR"
+ *
+ *  @note This function depends on JTEST_TEST_FLAG_SET and JTEST_TEST_FLAG_CLR.
+ */
+#define JTEST_TEST_XXX_FLAG(jtest_test_ptr, flag_name, xxx)                  \
+    do                                                                       \
+    {                                                                        \
+        JTEST_TEST_FLAG(jtest_test_ptr, flag_name) = JTEST_TEST_FLAG_##xxx ; \
+    } while (0)
+
+/**
+ *  Specification of #JTEST_TEST_XXX_FLAG to set #JTEST_TEST_t flags.
+ */
+#define JTEST_TEST_SET_FLAG(jtest_test_ptr, flag_name)                       \
+    JTEST_TEST_XXX_FLAG(jtest_test_ptr, flag_name, SET)
+
+/**
+ *  Specification of #JTEST_TEST_XXX_FLAG to clear #JTEST_TEST_t flags.
+ */
+#define JTEST_TEST_CLR_FLAG(jtest_test_ptr, flag_name)                       \
+    JTEST_TEST_XXX_FLAG(jtest_test_ptr, flag_name, CLR)
+
+/**
+ *  Evaluate to true if the #JTEST_TEST_t is enabled.
+ */
+#define JTEST_TEST_IS_ENABLED(jtest_test_ptr)                           \
+    (JTEST_TEST_FLAG(jtest_test_ptr, enabled) == JTEST_TEST_FLAG_SET)
+
+#endif /* _JTEST_TEST_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/jtest_test_call.h

@@ -0,0 +1,121 @@
+#ifndef _JTEST_TEST_CALL_H_
+#define _JTEST_TEST_CALL_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+#include "jtest_test.h"
+#include "jtest_test_define.h"
+#include "jtest_fw.h"
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Exectute the test in the #JTEST_TEST_t struct associated with the identifier
+ *  test_fn and store the result in retval.
+ */
+#define JTEST_TEST_RUN(retval, test_fn)                                 \
+    do                                                                  \
+    {                                                                   \
+        JTEST_DUMP_STR("Test Name:\n");                                 \
+        JTEST_DUMP_STR(JTEST_TEST_STRUCT_NAME(test_fn).test_fn_str);    \
+        JTEST_DUMP_STR("Function Under Test:\n");                       \
+        JTEST_DUMP_STR(JTEST_TEST_STRUCT_NAME(test_fn).fut_str);        \
+        retval = JTEST_TEST_STRUCT_NAME(test_fn).test_fn_ptr();         \
+    } while (0)
+
+/**
+ *  Update the enclosing #JTEST_GROUP_t's pass/fail information based on
+ *  test_retval.
+ *
+ *  @param test_retval A #JTEST_TEST_RET_enum for the current test.
+ *
+ *  @warning Only use if #JTEST_TEST_t is called in the context of a
+ *  #JTEST_GROUP_t.
+ */
+#define JTEST_TEST_UPDATE_PARENT_GROUP_PF(test_retval)              \
+    do                                                              \
+    {                                                               \
+        /* Update enclosing JTEST_GROUP_t with pass/fail info */    \
+        if (test_retval == JTEST_TEST_PASSED)                       \
+        {                                                           \
+            JTEST_GROUP_INC_PASSED(JTEST_CURRENT_GROUP_PTR(), 1);   \
+        } else {                                                    \
+            JTEST_GROUP_INC_FAILED(JTEST_CURRENT_GROUP_PTR(), 1);   \
+        }                                                           \
+    } while (0)
+
+/**
+ *  Update the #JTEST_FW with pass/fail information based on test_retval.
+ *
+ *  @param test_retval A #JTEST_TEST_RET_enum for the current test.
+ */
+#define JTEST_TEST_UPDATE_FW_PF(test_retval)                        \
+    do                                                              \
+    {                                                               \
+        /* Update the JTEST_FW with pass/fail info */                \
+        if (test_retval == JTEST_TEST_PASSED)                       \
+        {                                                           \
+            JTEST_FW_INC_PASSED( 1);                                \
+        } else {                                                    \
+            JTEST_FW_INC_FAILED(1);                                 \
+        }                                                           \
+    } while (0)
+
+/**
+ *  Update the enclosing JTEST_GROUP_t's pass/fail information, or the
+ *  #JTEST_FW's if this test has no enclosing #JTEST_GROUP_t.
+ *
+ *  @param test_retval A #JTEST_TEST_RET_enum for the current test.
+ */
+#define JTEST_TEST_UPDATE_PARENT_GROUP_OR_FW_PF(test_retval)            \
+    do                                                                  \
+    {                                                                   \
+        /* Update pass-fail information */                              \
+        if (JTEST_CURRENT_GROUP_PTR() /* Non-null */)                    \
+        {                                                               \
+            JTEST_TEST_UPDATE_PARENT_GROUP_PF(test_retval);             \
+        } else {                                                        \
+            JTEST_TEST_UPDATE_FW_PF(test_retval);                       \
+        }                                                               \
+    } while (0)
+
+/**
+ *  Dump the results of the test to the Keil Debugger.
+ */
+#define JTEST_TEST_DUMP_RESULTS(test_retval)        \
+        do                                          \
+        {                                           \
+            if (test_retval == JTEST_TEST_PASSED)   \
+            {                                       \
+                JTEST_DUMP_STR("Test Passed\n");      \
+            } else {                                \
+                JTEST_DUMP_STR("Test Failed\n");      \
+            }                                       \
+        } while (0)
+
+/**
+ *  Call the #JTEST_TEST_t assocaited with the identifier test_fn.
+ */
+#define JTEST_TEST_CALL(test_fn)                                        \
+    do                                                                  \
+    {                                                                   \
+        if (JTEST_TEST_IS_ENABLED(&JTEST_TEST_STRUCT_NAME(test_fn)))    \
+        {                                                               \
+            /* Default to failure */                                    \
+            JTEST_TEST_RET_t __jtest_test_ret = JTEST_TEST_FAILED;      \
+                                                                        \
+            JTEST_ACT_TEST_START();                                     \
+            JTEST_TEST_RUN(__jtest_test_ret, test_fn);                  \
+                                                                        \
+            /* Update pass-fail information */                          \
+            JTEST_TEST_UPDATE_PARENT_GROUP_OR_FW_PF(__jtest_test_ret);  \
+                                                                        \
+            JTEST_TEST_DUMP_RESULTS(__jtest_test_ret);                  \
+            JTEST_ACT_TEST_END();                                       \
+        }                                                               \
+    } while (0)
+
+#endif /* _JTEST_TEST_CALL_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/jtest_test_define.h

@@ -0,0 +1,133 @@
+#ifndef _JTEST_TEST_DEFINE_H_
+#define _JTEST_TEST_DEFINE_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+
+#include "jtest_util.h"
+#include "jtest_define.h"
+#include "jtest_test.h"
+
+/* For defining macros with optional arguments */
+#include "opt_arg/opt_arg.h"
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Prefix for all #JTEST_TEST_t structs.
+ */
+#define JTEST_TEST_STRUCT_NAME_PREFIX G_JTEST_TEST_STRUCT_
+
+/**
+ *  Define test template used by #JTEST_TEST_t tests.
+ */
+#define JTEST_TEST_FN_TEMPLATE(test_fn)                         \
+    JTEST_TEST_RET_t test_fn(void)
+
+#define JTEST_TEST_FN_PROTOTYPE JTEST_TEST_FN_TEMPLATE /**< Alias for
+                                                        * #JTEST_TEST_FN_TEMPLATE. */
+
+/**
+ *  Evaluate to the name of the #JTEST_TEST_t struct associated with test_fn.
+ */
+#define JTEST_TEST_STRUCT_NAME(test_fn)                         \
+    JTEST_STRUCT_NAME(JTEST_TEST_STRUCT_NAME_PREFIX, test_fn)
+
+/**
+ *  Define a #JTEST_TEST_t struct based on the given test_fn.
+ */
+#define JTEST_TEST_DEFINE_STRUCT(test_fn)                   \
+    JTEST_DEFINE_STRUCT(JTEST_TEST_t,                       \
+                        JTEST_TEST_STRUCT_NAME(test_fn))
+
+/**
+ *  Declare a #JTEST_TEST_t struct based on the given test_fn.
+ */
+#define JTEST_TEST_DECLARE_STRUCT(test_fn)      \
+    JTEST_DECLARE_STRUCT(JTEST_TEST_DEFINE_STRUCT(test_fn))
+
+/**
+ *  Contents needed to initialize a JTEST_TEST_t struct.
+ */
+#define JTEST_TEST_STRUCT_INIT(test_fn, fut, enable)    \
+    test_fn,                                            \
+        STR_NL(test_fn),                                   \
+        STR_NL(fut),                                       \
+    {                                                   \
+        {                                               \
+            enable,                                     \
+                0                                       \
+        }                                               \
+    }                                                   \
+        
+
+/**
+ *  Initialize the contents of a #JTEST_TEST_t struct.
+ */
+#define JTEST_TEST_INIT(test_fn, fut, enable)              \
+    JTEST_TEST_DEFINE_STRUCT(test_fn) = {                  \
+        JTEST_TEST_STRUCT_INIT(test_fn, fut, enable)       \
+    }
+
+/* Test Definition Macro */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Define a #JTEST_TEST_t object and a test function.
+ */
+#define _JTEST_DEFINE_TEST(test_fn, fut, enable)           \
+    JTEST_TEST_FN_PROTOTYPE(test_fn);                      \
+    JTEST_TEST_INIT(test_fn, fut, enable);                 \
+    JTEST_TEST_FN_PROTOTYPE(test_fn) /* Notice the lacking semicolon */
+
+/**
+ *  Declare a #JTEST_TEST_t object and a test function prototype.
+ */
+#define JTEST_DECLARE_TEST(test_fn)                                     \
+    JTEST_TEST_FN_PROTOTYPE(test_fn);                                   \
+    JTEST_TEST_DECLARE_STRUCT(test_fn) /* Note the lacking semicolon */
+
+/*--------------------------------------------------------------------------------*/
+/* Macros with optional arguments */
+/*--------------------------------------------------------------------------------*/
+
+/* Top-level Interface */
+#define JTEST_DEFINE_TEST(...)                             \
+    JTEST_DEFINE_TEST_(PP_NARG(__VA_ARGS__), ##__VA_ARGS__)
+
+/* Dispatch Macro*/
+#define JTEST_DEFINE_TEST_(N, ...)                         \
+    SPLICE(JTEST_DEFINE_TEST_, N)(__VA_ARGS__)
+
+/* Default Arguments */
+#define JTEST_DEFINE_TEST_DEFAULT_FUT /* Blank */
+#define JTEST_DEFINE_TEST_DEFAULT_ENABLE                   \
+    JTEST_TRUE                                 /* Tests enabled by
+                                                * default. */ 
+
+/* Dispatch Cases*/
+#define JTEST_DEFINE_TEST_1(_1)                            \
+    _JTEST_DEFINE_TEST(                                    \
+        _1,                                                \
+        JTEST_DEFINE_TEST_DEFAULT_FUT,                     \
+        JTEST_DEFINE_TEST_DEFAULT_ENABLE                   \
+        )
+
+#define JTEST_DEFINE_TEST_2(_1, _2)                        \
+    _JTEST_DEFINE_TEST(                                    \
+        _1,                                                \
+        _2,                                                \
+        JTEST_DEFINE_TEST_DEFAULT_ENABLE                   \
+        )
+
+#define JTEST_DEFINE_TEST_3(_1, _2, _3)                    \
+    _JTEST_DEFINE_TEST(                                    \
+        _1,                                                \
+        _2,                                                \
+        _3                                                 \
+        )
+
+#endif /* _JTEST_TEST_DEFINE_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/jtest_test_ret.h

@@ -0,0 +1,17 @@
+#ifndef _JTEST_TEST_RET_H_
+#define _JTEST_TEST_RET_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Type Definitions */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Values a #JTEST_TEST_t can return.
+ */
+typedef enum JTEST_TEST_RET_enum
+{
+    JTEST_TEST_PASSED,
+    JTEST_TEST_FAILED
+} JTEST_TEST_RET_t;
+
+#endif /* _JTEST_TEST_RET_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/jtest_util.h

@@ -0,0 +1,27 @@
+#ifndef _JTEST_UTIL_H_
+#define _JTEST_UTIL_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+
+#include "util/util.h"
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+
+/* Define boolean values for the framework. */
+#define JTEST_TRUE  1           /**< Value used for TRUE in JTEST. */
+#define JTEST_FALSE 0           /**< Value used for FALSE in JTEST. */
+
+/**
+ *  Set the value of the attribute in the struct to by struct_ptr to value.
+ */
+#define JTEST_SET_STRUCT_ATTRIBUTE(struct_ptr, attribute, value)    \
+    do                                                              \
+    {                                                               \
+        (struct_ptr)->attribute = (value);                          \
+    } while (0)
+
+#endif /* _JTEST_UTIL_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/opt_arg/opt_arg.h

@@ -0,0 +1,15 @@
+#ifndef _OPT_ARG_H_
+#define _OPT_ARG_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+
+#include "pp_narg.h"
+#include "splice.h"
+
+/* If you are Joseph Jaoudi, you have a snippet which expands into an
+   example. If you are not Joseph, but possess his code, study the examples. If
+   you have no examples, turn back contact Joseph. */
+
+#endif /* _OPT_ARG_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/opt_arg/pp_narg.h

@@ -0,0 +1,25 @@
+#ifndef _PP_NARG_H_
+#define _PP_NARG_H_
+
+#define PP_NARG(...)                                      \
+    PP_NARG_(__VA_ARGS__,PP_RSEQ_N())
+#define PP_NARG_(...)                                     \
+    PP_ARG_N(__VA_ARGS__)
+#define PP_ARG_N(                                         \
+                 _1, _2, _3, _4, _5, _6, _7, _8, _9,_10,  \
+                 _11,_12,_13,_14,_15,_16,_17,_18,_19,_20, \
+                 _21,_22,_23,_24,_25,_26,_27,_28,_29,_30, \
+                 _31,_32,_33,_34,_35,_36,_37,_38,_39,_40, \
+                 _41,_42,_43,_44,_45,_46,_47,_48,_49,_50, \
+                 _51,_52,_53,_54,_55,_56,_57,_58,_59,_60, \
+                 _61,_62,_63,N,...) N
+#define PP_RSEQ_N()                                       \
+    63,62,61,60,                                          \
+        59,58,57,56,55,54,53,52,51,50,                    \
+        49,48,47,46,45,44,43,42,41,40,                    \
+        39,38,37,36,35,34,33,32,31,30,                    \
+        29,28,27,26,25,24,23,22,21,20,                    \
+        19,18,17,16,15,14,13,12,11,10,                    \
+        9,8,7,6,5,4,3,2,1,0
+
+#endif /* _PP_NARG_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/opt_arg/splice.h

@@ -0,0 +1,8 @@
+#ifndef _SPLICE_H_
+#define _SPLICE_H_
+
+#define SPLICE(a,b) SPLICE_1(a,b)
+#define SPLICE_1(a,b) SPLICE_2(a,b)
+#define SPLICE_2(a,b) a##b
+
+#endif /* _SPLICE_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/inc/util/util.h

@@ -0,0 +1,52 @@
+#ifndef _UTIL_H_
+#define _UTIL_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Convert a symbol to a string and add a 'NewLine'.
+ */
+#define STR_NL(x)  STR1_NL(x)
+#define STR1_NL(x) (STR2_NL(x)"\n")
+#define STR2_NL(x) #x
+
+/**
+ *  Convert a symbol to a string.
+ */
+#define STR(x)  STR1(x)
+#define STR1(x) STR2(x)
+#define STR2(x) #x
+
+/**
+ *  Concatenate two symbols.
+ */
+#define CONCAT(a, b)  CONCAT1(a, b)
+#define CONCAT1(a, b) CONCAT2(a, b)
+#define CONCAT2(a, b) a##b
+
+
+/**
+ *  Place curly braces around a varaible number of macro arguments.
+ */
+#define CURLY(...) {__VA_ARGS__}
+
+/**
+ *  Place parenthesis around a variable number of macro arguments.
+ */
+#define PAREN(...) (__VA_ARGS__)
+
+/* Standard min/max macros. */
+#define MIN(x,y) (((x) < (y)) ? (x) : (y) )
+#define MAX(x,y) (((x) > (y)) ? (x) : (y) )
+
+/**
+ *  Bound value using low and high limits.
+ *
+ *  Evaluate to a number in the range, endpoint inclusive.
+ */
+#define BOUND(low, high, value)                 \
+    MAX(MIN(high, value), low)
+
+#endif /* _UTIL_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/src/jtest_cycle.c

@@ -0,0 +1,9 @@
+#include "../inc/jtest_cycle.h"
+#include <inttypes.h>
+
+/*--------------------------------------------------------------------------------*/
+/* Define Module Variables */
+/*--------------------------------------------------------------------------------*/
+
+/* const char * JTEST_CYCLE_STRF = "Running: %s\nCycles: %" PRIu32 "\n"; */
+const char * JTEST_CYCLE_STRF = "Cycles: %" PRIu32 "\n"; /* function name + parameter string skipped */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/src/jtest_dump_str_segments.c

@@ -0,0 +1,36 @@
+#include "jtest_fw.h"
+
+/**
+ *  Dump the JTEST_FW.str_buffer the Keil framework in pieces.
+ *
+ *  The JTEST_FW.str_buffer contains more characters than the Keil framework can
+ *  dump at once. This function dumps them in blocks.
+ */
+void jtest_dump_str_segments(void)
+{
+    uint32_t seg_idx      = 0;
+    uint32_t memmove_idx = 0;
+    uint32_t seg_cnt  =
+        (strlen(JTEST_FW.str_buffer) / JTEST_STR_MAX_OUTPUT_SIZE) + 1;
+
+    for( seg_idx = 0; seg_idx < seg_cnt; ++seg_idx)
+    {
+        JTEST_TRIGGER_ACTION(dump_str);
+
+        if (seg_idx < JTEST_STR_MAX_OUTPUT_SEGMENTS)
+        {
+            memmove_idx = 0;
+            while (memmove_idx < (seg_cnt - seg_idx -1) )
+            {
+                memmove(
+                    JTEST_FW.str_buffer+
+                    (memmove_idx* JTEST_STR_MAX_OUTPUT_SIZE),
+                    JTEST_FW.str_buffer+
+                    ((memmove_idx+1)*JTEST_STR_MAX_OUTPUT_SIZE),
+                    JTEST_BUF_SIZE);
+                ++memmove_idx;
+            }
+        }
+    }
+    return;
+}

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/src/jtest_fw.c

@@ -0,0 +1,9 @@
+#include "../inc/jtest.h"
+
+/*--------------------------------------------------------------------------------*/
+/* Define Global Variables */
+/*--------------------------------------------------------------------------------*/
+
+char JTEST_FW_STR_BUFFER[JTEST_BUF_SIZE] = {0};
+
+volatile JTEST_FW_t JTEST_FW = {0};

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/JTest/src/jtest_trigger_action.c

@@ -0,0 +1,37 @@
+
+#include "jtest_fw.h"
+
+void test_start    (void) {
+//  ;
+  JTEST_FW.test_start++;
+}
+
+void test_end      (void) {
+//  ;
+  JTEST_FW.test_end++;
+}
+
+void group_start   (void) {
+//  ;
+  JTEST_FW.group_start++;
+}
+
+void group_end     (void) {
+//  ;
+  JTEST_FW.group_end++;
+}
+
+void dump_str      (void) {
+//  ;
+  JTEST_FW.dump_str++;
+}
+
+void dump_data     (void) {
+//  ;
+  JTEST_FW.dump_data++;
+}
+
+void exit_fw       (void) {
+//  ;
+  JTEST_FW.exit_fw++;
+}

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/inc/all_tests.h

@@ -0,0 +1,9 @@
+#ifndef _ALL_TESTS_H_
+#define _ALL_TESTS_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Declare Test Groups */
+/*--------------------------------------------------------------------------------*/
+JTEST_DECLARE_GROUP(all_tests);
+
+#endif /* _ALL_TESTS_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/inc/basic_math_tests/basic_math_templates.h

@@ -0,0 +1,267 @@
+#ifndef _BASIC_MATH_TEMPLATES_H_
+#define _BASIC_MATH_TEMPLATES_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+#include "test_templates.h"
+
+/*--------------------------------------------------------------------------------*/
+/* Group Specific Templates */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Compare the outputs used by basic math tests for the function under test and
+ *  the reference function.
+ */
+#define BASIC_MATH_COMPARE_INTERFACE(block_size, output_type)   \
+    TEST_ASSERT_BUFFERS_EQUAL(                                  \
+        basic_math_output_ref.data_ptr,                         \
+        basic_math_output_fut.data_ptr,                         \
+        block_size * sizeof(output_type))
+
+/*
+ * Comparison SNR thresholds for the data types used in basic_math_tests.
+ */
+#define BASIC_MATH_SNR_THRESHOLD_float32_t 120
+#define BASIC_MATH_SNR_THRESHOLD_q31_t 100
+#define BASIC_MATH_SNR_THRESHOLD_q15_t 75
+#define BASIC_MATH_SNR_THRESHOLD_q7_t 25
+
+/**
+ *  Compare reference and fut outputs using SNR.
+ *
+ *  @note The outputs are converted to float32_t before comparison.
+ */
+#define BASIC_MATH_SNR_COMPARE_INTERFACE(block_size, output_type)   \
+    do                                                              \
+    {                                                               \
+        TEST_CONVERT_AND_ASSERT_SNR(                                \
+            basic_math_output_f32_ref,                              \
+            basic_math_output_ref.data_ptr,                         \
+            basic_math_output_f32_fut,                              \
+            basic_math_output_fut.data_ptr,                         \
+            block_size,                                             \
+            output_type,                                            \
+            BASIC_MATH_SNR_THRESHOLD_##output_type                  \
+            );                                                      \
+    } while (0)
+
+
+/**
+ *  Compare reference and fut outputs using SNR.
+ *
+ *  @note The outputs are converted to float32_t before comparison.
+ */
+#define BASIC_MATH_SNR_ELT1_COMPARE_INTERFACE(block_size, output_type)  \
+    do                                                                  \
+    {                                                                   \
+        TEST_CONVERT_AND_ASSERT_SNR(                                    \
+            basic_math_output_f32_ref,                                  \
+            basic_math_output_ref.data_ptr,                             \
+            basic_math_output_f32_fut,                                  \
+            basic_math_output_fut.data_ptr,                             \
+            1,                                                          \
+            output_type,                                                \
+            BASIC_MATH_SNR_THRESHOLD_##output_type                      \
+            );                                                          \
+    } while (0)
+
+
+
+/*--------------------------------------------------------------------------------*/
+/* Input Interfaces */
+/*--------------------------------------------------------------------------------*/
+/*
+ *  General:
+ *  Input interfaces provide inputs to functions inside test templates.  They
+ *  ONLY provide the inputs.  The output variables should be hard coded.
+ *
+ *  The input interfaces must have the following format:
+ *
+ *  ARM_xxx_INPUT_INTERFACE() or
+ *  REF_xxx_INPUT_INTERFACE()
+ *
+ *  The xxx must be lowercase, and is intended to be the indentifying substring
+ *  in the function's name.  Acceptable values are 'sub' or 'add' from the
+ *  functions arm_add_q31.
+ */
+
+#define ARM_abs_INPUT_INTERFACE(input, block_size)              \
+    PAREN(input, basic_math_output_fut.data_ptr, block_size)
+
+#define REF_abs_INPUT_INTERFACE(input, block_size)              \
+    PAREN(input, basic_math_output_ref.data_ptr, block_size)
+
+#define ARM_add_INPUT_INTERFACE(input_a, input_b, block_size)           \
+    PAREN(input_a, input_b, basic_math_output_fut.data_ptr, block_size) \
+
+#define REF_add_INPUT_INTERFACE(input_a, input_b, block_size)           \
+    PAREN(input_a, input_b, basic_math_output_ref.data_ptr, block_size) \
+
+#define ARM_dot_prod_INPUT_INTERFACE(input_a, input_b, block_size)      \
+    PAREN(input_a, input_b, block_size, basic_math_output_fut.data_ptr) \
+
+#define REF_dot_prod_INPUT_INTERFACE(input_a, input_b, block_size)      \
+    PAREN(input_a, input_b, block_size, basic_math_output_ref.data_ptr) \
+
+#define ARM_mult_INPUT_INTERFACE(input_a, input_b, block_size)          \
+    PAREN(input_a, input_b, basic_math_output_fut.data_ptr, block_size) \
+
+#define REF_mult_INPUT_INTERFACE(input_a, input_b, block_size)          \
+    PAREN(input_a, input_b, basic_math_output_ref.data_ptr, block_size) \
+
+#define ARM_negate_INPUT_INTERFACE(input, block_size)           \
+    PAREN(input, basic_math_output_fut.data_ptr, block_size)
+
+#define REF_negate_INPUT_INTERFACE(input, block_size)           \
+    PAREN(input, basic_math_output_ref.data_ptr, block_size)
+
+#define ARM_offset_INPUT_INTERFACE(input, elt, block_size)          \
+    PAREN(input, elt, basic_math_output_fut.data_ptr, block_size)   \
+
+#define REF_offset_INPUT_INTERFACE(input, elt, block_size)          \
+    PAREN(input, elt, basic_math_output_ref.data_ptr, block_size)   \
+
+#define ARM_shift_INPUT_INTERFACE(input, elt, block_size)           \
+    PAREN(input, elt, basic_math_output_fut.data_ptr, block_size)   \
+
+#define REF_shift_INPUT_INTERFACE(input, elt, block_size)           \
+    PAREN(input, elt, basic_math_output_ref.data_ptr, block_size)   \
+
+#define ARM_scale_float_INPUT_INTERFACE(input, elt, block_size)     \
+    PAREN(input, elt, basic_math_output_fut.data_ptr, block_size)   \
+
+#define REF_scale_float_INPUT_INTERFACE(input, elt, block_size)     \
+    PAREN(input, elt, basic_math_output_ref.data_ptr, block_size)   \
+
+/* These two are for the fixed point functions */
+#define ARM_scale_INPUT_INTERFACE(input, elt1, elt2, block_size)        \
+    PAREN(input, elt1, elt2, basic_math_output_fut.data_ptr, block_size) \
+
+#define REF_scale_INPUT_INTERFACE(input, elt1, elt2, block_size)        \
+    PAREN(input, elt1, elt2, basic_math_output_ref.data_ptr, block_size) \
+
+#define ARM_sub_INPUT_INTERFACE(input_a, input_b, block_size)           \
+    PAREN(input_a, input_b, basic_math_output_fut.data_ptr, block_size) \
+
+#define REF_sub_INPUT_INTERFACE(input_a, input_b, block_size)           \
+    PAREN(input_a, input_b, basic_math_output_ref.data_ptr, block_size) \
+
+
+/*--------------------------------------------------------------------------------*/
+/* Test Templates */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Specialization of #TEST_TEMPLATE_BUF1_BLK() for basic math tests.
+ *
+ *  @note This macro relies on the existance of ARM_xxx_INPUT_INTERFACE and
+ *  REF_xxx_INPUT_INTERFACEs.
+ */
+#define BASIC_MATH_DEFINE_TEST_TEMPLATE_BUF1_BLK(fn_name,       \
+                                                 suffix,        \
+                                                 input_type,    \
+                                                 output_type)   \
+    JTEST_DEFINE_TEST(arm_##fn_name##_##suffix##_test,          \
+                      arm_##fn_name##_##suffix)                 \
+    {                                                           \
+        TEST_TEMPLATE_BUF1_BLK(                                 \
+            basic_math_f_all,                                   \
+            basic_math_block_sizes,                             \
+            input_type,                                         \
+            output_type,                                        \
+            arm_##fn_name##_##suffix,                           \
+            ARM_##fn_name##_INPUT_INTERFACE,                    \
+            ref_##fn_name##_##suffix,                           \
+            REF_##fn_name##_INPUT_INTERFACE,                    \
+            BASIC_MATH_COMPARE_INTERFACE);                      \
+    }
+
+/**
+ *  Specialization of #TEST_TEMPLATE_BUF2_BLK() for basic math tests.
+ *
+ *  @note This macro relies on the existance of ARM_xxx_INPUT_INTERFACE and
+ *  REF_xxx_INPUT_INTERFACEs.
+ */
+#define BASIC_MATH_DEFINE_TEST_TEMPLATE_BUF2_BLK(fn_name,               \
+                                                 suffix,                \
+                                                 input_type,            \
+                                                 output_type,           \
+                                                 comparison_interface)  \
+    JTEST_DEFINE_TEST(arm_##fn_name##_##suffix##_test,                  \
+                      arm_##fn_name##_##suffix)                         \
+    {                                                                   \
+        TEST_TEMPLATE_BUF2_BLK(                                         \
+            basic_math_f_all,                                           \
+            basic_math_f_all,                                           \
+            basic_math_block_sizes,                                     \
+            input_type,                                                 \
+            output_type,                                                \
+            arm_##fn_name##_##suffix,                                   \
+            ARM_##fn_name##_INPUT_INTERFACE,                            \
+            ref_##fn_name##_##suffix,                                   \
+            REF_##fn_name##_INPUT_INTERFACE,                            \
+            comparison_interface);                                      \
+    }
+
+/**
+ *  Specialization of #TEST_TEMPLATE_BUF1_ELT1_BLK() for basic math tests.
+ *
+ *  @note This macro relies on the existance of ARM_xxx_INPUT_INTERFACE and
+ *  REF_xxx_INPUT_INTERFACEs.
+ */
+#define BASIC_MATH_DEFINE_TEST_TEMPLATE_BUF1_ELT1_BLK(fn_name,      \
+                                                      suffix,       \
+                                                      input_type,   \
+                                                      elt_type,     \
+                                                      output_type)  \
+    JTEST_DEFINE_TEST(arm_##fn_name##_##suffix##_test,              \
+                      arm_##fn_name##_##suffix)                     \
+    {                                                               \
+        TEST_TEMPLATE_BUF1_ELT1_BLK(                                \
+            basic_math_f_all,                                       \
+            basic_math_elts,                                        \
+            basic_math_block_sizes,                                 \
+            input_type,                                             \
+            elt_type,                                               \
+            output_type,                                            \
+            arm_##fn_name##_##suffix,                               \
+            ARM_##fn_name##_INPUT_INTERFACE,                        \
+            ref_##fn_name##_##suffix,                               \
+            REF_##fn_name##_INPUT_INTERFACE,                        \
+            BASIC_MATH_COMPARE_INTERFACE);                          \
+    }
+
+/**
+ *  Specialization of #TEST_TEMPLATE_BUF1_ELT2_BLK() for basic math tests.
+ *
+ *  @note This macro relies on the existance of ARM_xxx_INPUT_INTERFACE and
+ *  REF_xxx_INPUT_INTERFACEs.
+ */
+#define BASIC_MATH_DEFINE_TEST_TEMPLATE_BUF1_ELT2_BLK(fn_name,      \
+                                                      suffix,       \
+                                                      input_type,   \
+                                                      elt1_type,    \
+                                                      elt2_type,    \
+                                                      output_type)  \
+    JTEST_DEFINE_TEST(arm_##fn_name##_##suffix##_test,              \
+                      arm_##fn_name##_##suffix)                     \
+    {                                                               \
+        TEST_TEMPLATE_BUF1_ELT2_BLK(                                \
+            basic_math_f_all,                                       \
+            basic_math_elts,                                        \
+            basic_math_elts2,                                       \
+            basic_math_block_sizes,                                 \
+            input_type,                                             \
+            elt1_type,                                              \
+            elt2_type,                                              \
+            output_type,                                            \
+            arm_##fn_name##_##suffix,                               \
+            ARM_##fn_name##_INPUT_INTERFACE,                        \
+            ref_##fn_name##_##suffix,                               \
+            REF_##fn_name##_INPUT_INTERFACE,                        \
+            BASIC_MATH_COMPARE_INTERFACE);                          \
+    }
+
+#endif /* _BASIC_MATH_TEMPLATES_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/inc/basic_math_tests/basic_math_test_data.h

@@ -0,0 +1,46 @@
+#ifndef ARM_BASIC_MATH_TEST_DATA_H
+#define ARM_BASIC_MATH_TEST_DATA_H
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+
+#include "arr_desc.h"
+#include "arm_math.h"
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+#define BASIC_MATH_MAX_INPUT_ELEMENTS 32
+#define BASIC_MATH_BIGGEST_INPUT_TYPE float32_t
+
+/*--------------------------------------------------------------------------------*/
+/* Declare Variables */
+/*--------------------------------------------------------------------------------*/
+
+/* Input/Output Buffers */
+ARR_DESC_DECLARE(basic_math_output_fut);
+ARR_DESC_DECLARE(basic_math_output_ref);
+
+extern BASIC_MATH_BIGGEST_INPUT_TYPE
+basic_math_output_f32_ref[BASIC_MATH_MAX_INPUT_ELEMENTS];
+
+extern BASIC_MATH_BIGGEST_INPUT_TYPE
+basic_math_output_f32_fut[BASIC_MATH_MAX_INPUT_ELEMENTS];
+
+/* Block Sizes*/
+ARR_DESC_DECLARE(basic_math_block_sizes);
+
+/* Numbers */
+ARR_DESC_DECLARE(basic_math_elts);
+ARR_DESC_DECLARE(basic_math_elts2);
+ARR_DESC_DECLARE(basic_math_eltsf);
+
+/* Float Inputs */
+ARR_DESC_DECLARE(basic_math_zeros);
+ARR_DESC_DECLARE(basic_math_f_2);
+ARR_DESC_DECLARE(basic_math_f_15);
+ARR_DESC_DECLARE(basic_math_f_32);
+ARR_DESC_DECLARE(basic_math_f_all);
+
+#endif

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/inc/basic_math_tests/basic_math_test_group.h

@@ -0,0 +1,9 @@
+#ifndef _BASIC_MATH_TEST_GROUP_H_
+#define _BASIC_MATH_TEST_GROUP_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Declare Test Groups */
+/*--------------------------------------------------------------------------------*/
+JTEST_DECLARE_GROUP(basic_math_tests);
+
+#endif /* _BASIC_MATH_TEST_GROUP_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/inc/basic_math_tests/basic_math_tests.h

@@ -0,0 +1,17 @@
+#ifndef _BASIC_MATH_TESTS_H_
+#define _BASIC_MATH_TESTS_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Test/Group Declarations */
+/*--------------------------------------------------------------------------------*/
+JTEST_DECLARE_GROUP(abs_tests);
+JTEST_DECLARE_GROUP(add_tests);
+JTEST_DECLARE_GROUP(dot_prod_tests);
+JTEST_DECLARE_GROUP(mult_tests);
+JTEST_DECLARE_GROUP(negate_tests);
+JTEST_DECLARE_GROUP(offset_tests);
+JTEST_DECLARE_GROUP(scale_tests);
+JTEST_DECLARE_GROUP(shift_tests);
+JTEST_DECLARE_GROUP(sub_tests);
+
+#endif /* _BASIC_MATH_TESTS_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/inc/complex_math_tests/complex_math_templates.h

@@ -0,0 +1,222 @@
+#ifndef _COMPLEX_MATH_TEMPLATES_H_
+#define _COMPLEX_MATH_TEMPLATES_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+#include "test_templates.h"
+
+/*--------------------------------------------------------------------------------*/
+/* Group Specific Templates */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Compare the real outputs from the function under test and the reference
+ *  function.
+ */
+#define COMPLEX_MATH_COMPARE_RE_INTERFACE(block_size, output_type)  \
+    TEST_ASSERT_BUFFERS_EQUAL(                                      \
+        complex_math_output_ref_a.data_ptr,                         \
+        complex_math_output_fut_a.data_ptr,                         \
+        block_size * sizeof(output_type))
+
+/**
+ *  Compare the real and imaginary outputs from the function under test and the
+ *  reference function.
+ */
+#define COMPLEX_MATH_COMPARE_CMPLX_INTERFACE(block_size, output_type)   \
+    do                                                                  \
+    {                                                                   \
+        COMPLEX_MATH_COMPARE_RE_INTERFACE(block_size * 2, output_type); \
+    } while (0)
+
+
+/*
+ * Comparison SNR thresholds for the data types used in complex_math_tests.
+ */
+#define COMPLEX_MATH_SNR_THRESHOLD_float32_t 120
+#define COMPLEX_MATH_SNR_THRESHOLD_q31_t 100
+#define COMPLEX_MATH_SNR_THRESHOLD_q15_t 75
+
+/**
+ *  Compare reference and fut outputs using SNR.
+ *
+ *  The output_suffix specifies which output buffers to use for the
+ *  comparison. An output_suffix of 'a' expands to the following buffers:
+ *
+ *  - complex_math_output_f32_ref_a
+ *  - complex_math_output_f32_fut_a
+ *  - complex_math_output_ref_a
+ *  - complex_math_output_fut_a
+ *
+ *  @note The outputs are converted to float32_t before comparison.
+ */
+#define COMPLEX_MATH_SNR_COMPARE_OUT_INTERFACE(block_size,      \
+                                               output_type,     \
+                                               output_suffix)   \
+    do                                                          \
+    {                                                           \
+        TEST_CONVERT_AND_ASSERT_SNR(                            \
+            complex_math_output_f32_ref_##output_suffix,        \
+            complex_math_output_ref_##output_suffix.data_ptr,   \
+            complex_math_output_f32_fut_##output_suffix,        \
+            complex_math_output_fut_##output_suffix.data_ptr,   \
+            block_size,                                         \
+            output_type,                                        \
+            COMPLEX_MATH_SNR_THRESHOLD_##output_type            \
+            );                                                  \
+    } while (0)
+
+/**
+ *  Specification of #COMPLEX_MATH_SNR_COMPARE_INTERFACE() for real outputs.
+ */
+#define COMPLEX_MATH_SNR_COMPARE_RE_INTERFACE(block_size,       \
+                                                   output_type) \
+    COMPLEX_MATH_SNR_COMPARE_OUT_INTERFACE(block_size,          \
+                                           output_type,         \
+                                           a)
+
+/**
+ *  Specification of #COMPLEX_MATH_SNR_COMPARE_INTERFACE() for complex outputs.
+ */
+#define COMPLEX_MATH_SNR_COMPARE_CMPLX_INTERFACE(block_size,    \
+                                                 output_type)   \
+        COMPLEX_MATH_SNR_COMPARE_OUT_INTERFACE(block_size * 2,  \
+                                               output_type,     \
+                                               a)
+
+/**
+ *  Compare reference and fut split outputs using SNR.
+ *
+ *  'Split' refers to two separate output buffers; one for real and one for
+ *  complex.
+ */
+#define COMPLEX_MATH_SNR_COMPARE_SPLIT_INTERFACE(block_size,    \
+                                                 output_type)   \
+        do                                                      \
+        {                                                       \
+            COMPLEX_MATH_SNR_COMPARE_OUT_INTERFACE(block_size,  \
+                                                   output_type, \
+                                                   a);          \
+            COMPLEX_MATH_SNR_COMPARE_OUT_INTERFACE(block_size,  \
+                                                   output_type, \
+                                                   b);          \
+        } while (0)
+
+
+/*--------------------------------------------------------------------------------*/
+/* Input Interfaces */
+/*--------------------------------------------------------------------------------*/
+/*
+ *  General:
+ *  Input interfaces provide inputs to functions inside test templates.  They
+ *  ONLY provide the inputs.  The output variables should be hard coded.
+ *
+ *  The input interfaces must have the following format:
+ *
+ *  ARM_xxx_INPUT_INTERFACE() or
+ *  REF_xxx_INPUT_INTERFACE()
+ *
+ *  The xxx must be lowercase, and is intended to be the indentifying substring
+ *  in the function's name.  Acceptable values are 'sub' or 'add' from the
+ *  functions arm_add_q31.
+ */
+
+#define ARM_cmplx_conj_INPUT_INTERFACE(input, block_size)           \
+    PAREN(input, complex_math_output_fut_a.data_ptr, block_size)
+
+#define REF_cmplx_conj_INPUT_INTERFACE(input, block_size)           \
+    PAREN(input, complex_math_output_ref_a.data_ptr, block_size)
+
+#define ARM_cmplx_dot_prod_INPUT_INTERFACE(input_a, input_b, block_size) \
+    PAREN(input_a, input_b, block_size,                                 \
+          complex_math_output_fut_a.data_ptr,                          \
+          complex_math_output_fut_b.data_ptr)
+
+#define REF_cmplx_dot_prod_INPUT_INTERFACE(input_a, input_b, block_size) \
+    PAREN(input_a, input_b, block_size,                                 \
+          complex_math_output_ref_a.data_ptr,                          \
+          complex_math_output_ref_b.data_ptr)
+
+#define ARM_cmplx_mag_INPUT_INTERFACE(input, block_size)            \
+    PAREN(input, complex_math_output_fut_a.data_ptr, block_size)
+
+#define REF_cmplx_mag_INPUT_INTERFACE(input, block_size)            \
+    PAREN(input, complex_math_output_ref_a.data_ptr, block_size)
+
+#define ARM_cmplx_mag_squared_INPUT_INTERFACE(input, block_size)    \
+    PAREN(input, complex_math_output_fut_a.data_ptr, block_size)
+
+#define REF_cmplx_mag_squared_INPUT_INTERFACE(input, block_size)    \
+    PAREN(input, complex_math_output_ref_a.data_ptr, block_size)
+
+#define ARM_cmplx_mult_cmplx_INPUT_INTERFACE(input_a, input_b, block_size) \
+    PAREN(input_a, input_b, complex_math_output_fut_a.data_ptr, block_size)
+
+#define REF_cmplx_mult_cmplx_INPUT_INTERFACE(input_a, input_b, block_size) \
+    PAREN(input_a, input_b, complex_math_output_ref_a.data_ptr, block_size)
+
+#define ARM_cmplx_mult_real_INPUT_INTERFACE(input_a, input_b, block_size) \
+    PAREN(input_a, input_b, complex_math_output_fut_a.data_ptr, block_size)
+
+#define REF_cmplx_mult_real_INPUT_INTERFACE(input_a, input_b, block_size) \
+    PAREN(input_a, input_b, complex_math_output_ref_a.data_ptr, block_size)
+
+/*--------------------------------------------------------------------------------*/
+/* Test Templates */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ *  Specialization of #TEST_TEMPLATE_BUF1_BLK() for complex math tests.
+ *
+ *  @note This macro relies on the existance of ARM_xxx_INPUT_INTERFACE and
+ *  REF_xxx_INPUT_INTERFACEs.
+ */
+#define COMPLEX_MATH_DEFINE_TEST_TEMPLATE_BUF1_BLK(fn_name,         \
+                                                   suffix,          \
+                                                   input_type,      \
+                                                   output_type,     \
+                                                   comparison_interface) \
+    JTEST_DEFINE_TEST(arm_##fn_name##_##suffix##_test,              \
+                      arm_##fn_name##_##suffix)                     \
+    {                                                               \
+        TEST_TEMPLATE_BUF1_BLK(                                     \
+            complex_math_f_all,                                     \
+            complex_math_block_sizes,                               \
+            input_type,                                             \
+            output_type,                                            \
+            arm_##fn_name##_##suffix,                               \
+            ARM_##fn_name##_INPUT_INTERFACE,                        \
+            ref_##fn_name##_##suffix,                               \
+            REF_##fn_name##_INPUT_INTERFACE,                        \
+            comparison_interface);                                  \
+    }
+
+/**
+ *  Specialization of #TEST_TEMPLATE_BUF2_BLK1() for complex math tests.
+ *
+ *  @note This macro relies on the existance of ARM_xxx_INPUT_INTERFACE and
+ *  REF_xxx_INPUT_INTERFACEs.
+ */
+#define COMPLEX_MATH_DEFINE_TEST_TEMPLATE_BUF2_BLK(fn_name,         \
+                                                   suffix,          \
+                                                   input_type,      \
+                                                   output_type,     \
+                                                   comparison_interface) \
+    JTEST_DEFINE_TEST(arm_##fn_name##_##suffix##_test,              \
+                      arm_##fn_name##_##suffix)                     \
+    {                                                               \
+        TEST_TEMPLATE_BUF2_BLK(                                     \
+            complex_math_f_all,                                     \
+            complex_math_f_all,                                     \
+            complex_math_block_sizes,                               \
+            input_type,                                             \
+            output_type,                                            \
+            arm_##fn_name##_##suffix,                               \
+            ARM_##fn_name##_INPUT_INTERFACE,                        \
+            ref_##fn_name##_##suffix,                               \
+            REF_##fn_name##_INPUT_INTERFACE,                        \
+            comparison_interface);                                  \
+    }
+
+#endif /* _COMPLEX_MATH_TEMPLATES_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/inc/complex_math_tests/complex_math_test_data.h

@@ -0,0 +1,50 @@
+#ifndef _COMPLEX_MATH_TEST_DATA_H_
+#define _COMPLEX_MATH_TEST_DATA_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+
+#include "arr_desc.h"
+#include "arm_math.h"
+
+/*--------------------------------------------------------------------------------*/
+/* Macros and Defines */
+/*--------------------------------------------------------------------------------*/
+#define COMPLEX_MATH_MAX_INPUT_ELEMENTS 32
+#define COMPLEX_MATH_BIGGEST_INPUT_TYPE float32_t
+
+/*--------------------------------------------------------------------------------*/
+/* Decalare Variables */
+/*--------------------------------------------------------------------------------*/
+
+/* Input/Output Buffers */
+ARR_DESC_DECLARE(complex_math_output_fut_a);
+ARR_DESC_DECLARE(complex_math_output_fut_b);
+ARR_DESC_DECLARE(complex_math_output_ref_a);
+ARR_DESC_DECLARE(complex_math_output_ref_b);
+
+extern COMPLEX_MATH_BIGGEST_INPUT_TYPE
+complex_math_output_f32_ref_a[COMPLEX_MATH_MAX_INPUT_ELEMENTS * 2];
+
+extern COMPLEX_MATH_BIGGEST_INPUT_TYPE
+complex_math_output_f32_ref_b[COMPLEX_MATH_MAX_INPUT_ELEMENTS * 2];
+
+extern COMPLEX_MATH_BIGGEST_INPUT_TYPE
+complex_math_output_f32_fut_a[COMPLEX_MATH_MAX_INPUT_ELEMENTS * 2];
+
+extern COMPLEX_MATH_BIGGEST_INPUT_TYPE
+complex_math_output_f32_fut_b[COMPLEX_MATH_MAX_INPUT_ELEMENTS * 2];
+
+/* Block Sizes*/
+ARR_DESC_DECLARE(complex_math_block_sizes);
+
+/* Float Inputs */
+ARR_DESC_DECLARE(complex_math_zeros);
+ARR_DESC_DECLARE(complex_math_f_2);
+ARR_DESC_DECLARE(complex_math_f_15);
+ARR_DESC_DECLARE(complex_math_f_32);
+ARR_DESC_DECLARE(complex_math_f_all);
+
+
+#endif /* _COMPLEX_MATH_TEST_DATA_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/inc/complex_math_tests/complex_math_test_group.h

@@ -0,0 +1,9 @@
+#ifndef _COMPLEX_MATH_TEST_GROUP_H_
+#define _COMPLEX_MATH_TEST_GROUP_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Declare Test Groups */
+/*--------------------------------------------------------------------------------*/
+JTEST_DECLARE_GROUP(complex_math_tests);
+
+#endif /* _COMPLEX_MATH_TEST_GROUP_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/inc/complex_math_tests/complex_math_tests.h

@@ -0,0 +1,14 @@
+#ifndef _COMPLEX_MATH_TESTS_H_
+#define _COMPLEX_MATH_TESTS_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Test/Group Declarations */
+/*--------------------------------------------------------------------------------*/
+JTEST_DECLARE_GROUP(cmplx_conj_tests);
+JTEST_DECLARE_GROUP(cmplx_dot_prod_tests);
+JTEST_DECLARE_GROUP(cmplx_mag_tests);
+JTEST_DECLARE_GROUP(cmplx_mag_squared_tests);
+JTEST_DECLARE_GROUP(cmplx_mult_cmplx_tests);
+JTEST_DECLARE_GROUP(cmplx_mult_real_tests);
+
+#endif /* _COMPLEX_MATH_TESTS_H_ */

Drivers/CMSIS/DSP/DSP_Lib_TestSuite/Common/inc/controller_tests/controller_templates.h

@@ -0,0 +1,46 @@
+#ifndef _CONTROLLER_TEMPLATES_H_
+#define _CONTROLLER_TEMPLATES_H_
+
+/*--------------------------------------------------------------------------------*/
+/* Includes */
+/*--------------------------------------------------------------------------------*/
+
+#include "test_templates.h"
+#include <string.h>             /* memcpy() */
+
+/*--------------------------------------------------------------------------------*/
+/* Group Specific Templates */
+/*--------------------------------------------------------------------------------*/
+
+/**
+ * Comparison SNR thresholds for the data types used in transform_tests.
+ */
+#define CONTROLLER_SNR_THRESHOLD_float32_t 110
+#define CONTROLLER_SNR_THRESHOLD_q31_t     100
+#define CONTROLLER_SNR_THRESHOLD_q15_t     45
+
+/**
+ *  Compare the outputs from the function under test and the reference
+ *  function using SNR.
+ */
+#define CONTROLLER_SNR_COMPARE_INTERFACE(block_size,    \
+                                         output_type)   \
+    do                                                  \
+    {                                                   \
+        TEST_CONVERT_AND_ASSERT_SNR(                    \
+            controller_output_f32_ref,                  \
+            (output_type *) controller_output_ref,      \
+            controller_output_f32_fut,                  \
+            (output_type *) controller_output_fut,      \
+            block_size,                                 \
+            output_type,                                \
+            CONTROLLER_SNR_THRESHOLD_##output_type      \
+            );                                          \
+    } while (0)
+
+
+/*--------------------------------------------------------------------------------*/
+/* TEST Templates */
+/*--------------------------------------------------------------------------------*/
+
+#endif /* _CONTROLLER_TEMPLATES_H_ */