Добавлены проверки на режим прерывания (пока ниче не работает)

CubeKeil Example/flash eeprom Example.ioc

@@ -11,7 +11,7 @@ Mcu.IP0=CRC
 Mcu.IP1=NVIC
 Mcu.IP2=RCC
 Mcu.IP3=RNG
-Mcu.IP4=SPI1
+Mcu.IP4=SPI2
 Mcu.IP5=SYS
 Mcu.IPNb=6
 Mcu.Name=STM32F407V(E-G)Tx
@@ -20,9 +20,9 @@ Mcu.Pin0=PH0-OSC_IN
 Mcu.Pin1=PH1-OSC_OUT
 Mcu.Pin10=VP_RNG_VS_RNG
 Mcu.Pin11=VP_SYS_VS_Systick
-Mcu.Pin2=PA5
-Mcu.Pin3=PA6
-Mcu.Pin4=PA7
+Mcu.Pin2=PB13
+Mcu.Pin3=PB14
+Mcu.Pin4=PB15
 Mcu.Pin5=PD12
 Mcu.Pin6=PD13
 Mcu.Pin7=PD14
@@ -45,12 +45,15 @@ NVIC.PriorityGroup=NVIC_PRIORITYGROUP_0
 NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:true\:false\:false
 NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:true\:true\:false
 NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:true\:false\:false
-PA5.Mode=Full_Duplex_Master
-PA5.Signal=SPI1_SCK
-PA6.Mode=Full_Duplex_Master
-PA6.Signal=SPI1_MISO
-PA7.Mode=Full_Duplex_Master
-PA7.Signal=SPI1_MOSI
+PB13.Locked=true
+PB13.Mode=Full_Duplex_Master
+PB13.Signal=SPI2_SCK
+PB14.Locked=true
+PB14.Mode=Full_Duplex_Master
+PB14.Signal=SPI2_MISO
+PB15.Locked=true
+PB15.Mode=Full_Duplex_Master
+PB15.Signal=SPI2_MOSI
 PD12.Locked=true
 PD12.Signal=GPIO_Output
 PD13.Locked=true
@@ -125,11 +128,11 @@ RCC.VCOI2SOutputFreq_Value=384000000
 RCC.VCOInputFreq_Value=2000000
 RCC.VCOOutputFreq_Value=128000000
 RCC.VcooutputI2S=192000000
-SPI1.CalculateBaudRate=4.0 MBits/s
-SPI1.Direction=SPI_DIRECTION_2LINES
-SPI1.IPParameters=VirtualType,Mode,Direction,CalculateBaudRate
-SPI1.Mode=SPI_MODE_MASTER
-SPI1.VirtualType=VM_MASTER
+SPI2.CalculateBaudRate=4.0 MBits/s
+SPI2.Direction=SPI_DIRECTION_2LINES
+SPI2.IPParameters=VirtualType,Mode,Direction,CalculateBaudRate
+SPI2.Mode=SPI_MODE_MASTER
+SPI2.VirtualType=VM_MASTER
 VP_CRC_VS_CRC.Mode=CRC_Activate
 VP_CRC_VS_CRC.Signal=CRC_VS_CRC
 VP_RNG_VS_RNG.Mode=RNG_Activate